Egan H. Doeven

A potential-controlled switch on/off mechanism for selective excitation in mixed electrochemiluminescent systems

We demonstrate the complete, rapid, and reversible switching between the emissions from two electrogenerated chemiluminescence (ECL) systems contained within the same solution, controlled by simple modification of the applied potential. The fundamental bases of the approach are the ability to selectively ‘switch on’ luminophores at distinct oxidation potentials, and an intriguing observation that the emission from the well-known electrochemiluminescent complex, fac-Ir(ppy)3, (where ppy is 2-phenylpyridinato), can be selectively ‘switched-off’ at high overpotentials. The dependence of this phenomenon on high concentrations of the co-reactant implicates quenching of the excited [Ir(ppy)3]* state by electron transfer. Rapid spectral scanning during modulation of the applied potential reveals well resolved maxima for mixtures comprising either green and red or green and blue luminophores, illustrating the vast potential of this approach for multiplexed ECL detection.

Red–Green–Blue Electrogenerated Chemiluminescence Utilizing a Digital Camera as Detector

Exploiting the distinct excitation and emission properties of concomitant electrochemiluminophores in conjunction with the inherent color selectivity of a conventional digital camera, we create a new strategy for multiplexed electrogenerated chemiluminescence detection, suitable for the development of low-cost, portable clinical diagnostic devices. Red, green and blue emitters can be efficiently resolved over the three-dimensional space of ECL intensity versus applied potential and emission wavelength. As the relative contribution ratio of each emitter to the photographic RGB channels is constant, the RGB ECL intensity versus applied-potential curves could be effectively isolated to a single emitter at each potential.

Use of a mobile phone for potentiostatic control with low cost paper-based microfluidic sensors

By exploiting its ability to play sounds, a mobile phone with suitable software installed can serve the basic functions of a potentiostat in controlling an applied potential to oxidise ECL-active molecules, while the resultant photonic signal is monitored using the camera in video mode. In combination with paper microfluidic sensors this opens significant new possibilities for low-cost, instrument-free sensing.

Selective Excitation of Concomitant Electrochemiluminophores: Tuning Emission Color by Electrode Potential†

ECL in 3D: Selective electrogenerated chemiluminescence (ECL) of several ruthenium and iridium complexes simultaneously in solution can be controlled by electrode potential (see picture; λem=emission wavelength). These luminescent redox systems create a range of new possibilities for multi-analyte ECL detection, assessment of interdependent electrochemical/spectroscopic properties, and color tuning in light-emitting devices.

Understanding electrogenerated chemiluminescence efficiency in blue-shifted iridium(III)-complexes: an experimental and theoretical study.

Compared to tris(2-phenylpyridine)iridium(III) ([Ir(ppy)3 ]), iridium(III) complexes containing difluorophenylpyridine (df-ppy) and/or an ancillary triazolylpyridine ligand [3-phenyl-1,2,4-triazol-5-ylpyridinato (ptp) or 1-benzyl-1,2,3-triazol-4-ylpyridine (ptb)] exhibit considerable hypsochromic shifts (ca. 25-60 nm), due to the significant stabilising effect of these ligands on the HOMO energy, whilst having relatively little effect on the LUMO. Despite their lower photoluminescence quantum yields compared with [Ir(ppy)3 ] and [Ir(df-ppy)3 ], the iridium(III) complexes containing triazolylpyridine ligands gave greater electrogenerated chemiluminescence (ECL) intensities (using tri-n-propylamine (TPA) as a co-reactant), which can in part be ascribed to the more energetically favourable reactions of the oxidised complex (M(+) ) with both TPA and its neutral radical oxidation product. The calculated iridium(III) complex LUMO energies were shown to be a good predictor of the corresponding M(+) LUMO energies, and both HOMO and LUMO levels are related to ECL efficiency. The theoretical and experimental data together show that the best strategy for the design of efficient new blue-shifted electrochemiluminophores is to aim to stabilise the HOMO, while only moderately stabilising the LUMO, thereby increasing the energy gap but ensuring favourable thermodynamics and kinetics for the ECL reaction. Of the iridium(III) complexes examined, [Ir(df-ppy)2 (ptb)](+) was most attractive as a blue-emitter for ECL detection, featuring a large hypsochromic shift (λmax =454 and 484 nm), superior co-reactant ECL intensity than the archetypal homoleptic green and blue emitters: [Ir(ppy)3 ] and [Ir(df-ppy)3 ] (by over 16-fold and threefold, respectively), and greater solubility in polar solvents.

Comparison of homoleptic and heteroleptic 2,2′-bipyridine and 1,10-phenanthroline ruthenium complexes as chemiluminescence and electrochemiluminescence reagents in aqueous solution

We have conducted a comprehensive comparative study of Ru(bipy)(3)(2+), Ru(bipy)(2)(phen)(2+), Ru(bipy)(phen)(2)(2+), and Ru(phen)(3)(2+) as chemiluminescence and electrochemiluminescence (ECL) reagents, to address several previous conflicting observations and gain a greater insight into their potential for chemical analysis. Clear trends were observed in many of their spectroscopic and electrochemical properties, but the relative chemiluminescence or ECL intensity with a range of analytes/co-reactants is complicated by the contribution of numerous (sometimes opposing) factors. Significantly, the reversibility of cyclic voltammetric responses for the complexes decreased as the number of phenanthroline ligands was increased, due to the lower stability of their ruthenium(III) form in the aqueous solvent. This trend was also evident over a longer timescale when the ruthenium(III) form was spectrophotometrically monitored after chemical oxidation of the ruthenium(II) complexes. In general, the greater stability of Ru(bipy)(3)(3+) resulted in lower blank signals, although this effect was less pronounced with ECL, where the reagent is oxidised in the presence of the co-reactants. Nevertheless, this shows the need to compare signal-to-blank ratios or detection limits, rather than the more common comparisons of overall signal intensity for different ruthenium complexes. Furthermore, our results support previous observations that, compared to Ru(bipy)(3)(2+), Ru(phen)(3)(2+) provides greater ECL and chemiluminescence intensities with oxalate, which in some circumstances translates to superior detection limits, but they do not support the subsequent generalised notion that Ru(phen)(3)(2+) is a more sensitive reagent than Ru(bipy)(3)(2+) for all analytes.

3D-printed and CNC milled flow-cells for chemiluminescence detection

Herein we explore modern fabrication techniques for the development of chemiluminescence detection flow-cells with features not attainable using the traditional coiled tubing approach. This includes the first 3D-printed chemiluminescence flow-cells, and a milled flow-cell designed to split the analyte stream into two separate detection zones within the same polymer chip. The flow-cells are compared to conventional detection systems using flow injection analysis (FIA) and high performance liquid chromatography (HPLC), with the fast chemiluminescence reactions of an acidic potassium permanganate reagent with morphine and a series of adrenergic phenolic amines.

Tailoring the fibre-to-matrix interface using click chemistry on carbon fibre surfaces

A convenient and effective strategy to control the surface chemistry of carbon fibres is presented, comprising electro-chemical reduction of aryl diazonium salts onto the surface, followed by ‘click chemistry’ to tether the desired surface characteristic of choice. The power of this approach was demonstrated by engineering a small-molecule interface between carbon fibre and an epoxy matrix improving interfacial shear strength by up to 220%, relative to unmodified control fibres. The techniques used in this work do not impede the fibre performance in tensile strength or Youngs modulus. This work provides a platform upon which any carbon fibre-to-resin interface can be easily and rapidly designed and implemented.

Reprint of: Use of a mobile phone for potentiostatic control with low cost paper-based microfluidic sensors.

By exploiting its ability to play sounds, a mobile phone with suitable software installed can serve the basic functions of a potentiostat in controlling an applied potential to oxidise ECL-active molecules, while the resultant photonic signal is monitored using the camera in video mode. In combination with paper microfluidic sensors this opens significant new possibilities for low-cost, instrument-free sensing.

Photoredox Catalysis of Intramolecular Cyclizations with a Reusable Silica‐Bound Ruthenium Complex

Photoredox catalysis with the use of a stable, reusable silica‐bound chromophore was applied to the intramolecular cyclization of a series of 2‐benzylidenehydrazinecarbothioamides to give 5‐phenyl‐1,3,4‐thiadiazol‐2‐amines. The catalyst was readily prepared by carbodiimide‐mediated coupling of commercially available amine‐functionalized silica beads to a carboxylic acid functionalized ruthenium complex. The immobilized catalyst was readily removed from the reaction product by filtration and was used eight times without loss of catalytic activity. This simple, safe, and practical method is an attractive alternative to conventional procedures.