Emine Sirin Karaarslan

Color stability and surface roughness of polished anterior restorative materials

The purpose of this study was to investigate the effects of different finishing-polishing techniques on the color stability and surface roughness of various anterior restorative materials after staining. A composite, a compomer, and a resin-modified glass ionomer were used to prepare 120 specimens. Specimens were divided into subgroups: polishing discs, liquid polishing material, aluminium oxidebonded discs, and control. The specimens were stained in a coffee solution. Color parameters (L*a*b*) and surface roughness before and after staining were measured. The color was affected by the material type (p<0.05) and finishing-polishing systems (p<0.05). The composite showed the highest color stability; however, the color differences of all groups were visible even to the nonskilled operator. The Ra values did not significantly change after staining for any of the restorative groups (p>0.05). The finishing-polishing systems had an effect on color after storing in staining solution.

Effects of Novel Finishing and Polishing Systems on Surface Roughness and Morphology of Nanocomposites

OBJECTIVES The purpose of this in vitro study was to evaluate the effects of different finishing/polishing techniques on the surface roughness of nanocomposites after thermocycling aging. MATERIALS AND METHODS Five contemporary resin-based composites (Clearfil Majesty ES-2, Filtek Z550, Estelite∑Quick, Zenit, Filtek Z250) were tested. For each resin-based composite, 50 disc-shaped specimens were prepared and groups were divided into five subgroups according to the finishing/polishing methods (n = 10): control, finishing/polishing brush, finishing/polishing disc, and two different finishing/polishing wheels. Before and after aging, the surface roughness of specimens was measured. For each treatment method two samples were analyzed using a scanning electron microscope. Two-way analysis of variance and paired samples t-tests were used to evaluate the data and the means were compared by Bonferroni tests (p ≤ 0.05). RESULTS Before aging, the Filtek Z250 resin with the Mylar strip group showed the lowest surface roughness (Ra) value (0.13 ± 0.03 µm, p < 0.05) and the Clearfil Majesty ES 2 resin with Occlubrush finishing/polishing system showed the highest (0.7 ± 0.13 µm, p < 0.05). After aging, the Clearfil Majesty ES 2 resin with the Mylar strip group showed the highest surface roughness (Ra) value (0.96 ± 0.4 µm) and the Clearfil Majesty ES 2 resin with the Sof-Lex aluminum oxide disc finishing/polishing system showed the lowest surface roughness (Ra) value (0.25 ± 0.06 µm, p < 0.05). CONCLUSIONS Composite type and finishing/polishing method significantly affected the surface roughness of composites before and after thermocycling aging. CLINICAL SIGNIFICANCE There were significant interactions between finishing/polishing methods and composite types for surface roughness. The results give clinicians some flexibility in choosing appropriate finishing/polishing techniques for each resin composite material. (J Esthet Restor Dent 28:247-261, 2016).

In vivo performance of two devices for occlusal caries detection.

OBJECTIVE The aim of this in vivo study was to compare the performance of light-emitting diode (LED)- and laser fluorescence (LF)-based devices with that of visual inspection (VI) in the diagnosis of occlusal caries. METHODS A total of 156 occlusal surfaces were investigated. Each occlusal surface was assessed with LED- and LF-based devices after a VI was performed. Pit and fissure opening was applied to the occlusal surfaces in which opacity or discoloration was distinctly visible after airdrying. The inter-examiner reliability of caries examination was assessed using the weighted κ statistics. The sensitivity, specificity, and accuracy of occlusal caries diagnosis using these methods were calculated according to the appropriate thresholds. RESULTS Acceptable inter-examiner agreement was found for the LED- and LF-based devices and VI (κ=0.61, κ=0.76, and κ=0.87, respectively). Higher specificity values were achieved at a T2 threshold for the LF-based device (0.76 and 0.80) and at a T1 threshold for the LED-based readings (0.60 and 0.62) and VI (0.90 and 0.93) for both observers. With regard to VI, higher sensitivity values were found at both thresholds for the two observers in comparing the three caries detection methods (0.98 at T1 and 0.96 at T2). The accuracy values for T1 were higher than those for the T2 values, for all three caries detection methods. CONCLUSIONS Caries lesions may be detected more accurately than clinically sound areas by both caries detection devices.

Clinical evaluation of direct composite restorations and inlays: Results at 12 months

Background: The purpose of this study was to compare the clinical performance of Class II direct and indirect composite restorations according to the United States Public Health Service criteria (USPHS). Materials and Methods: Seventy patients were included and four different composite resins, P60 (FP), SureFil Posterior (SP), Gradia Posterior (GP), and Bisco Aelite LS Packable (BAP) were used as direct restorative material. All of the composite resins except BAP were used as indirect restorative material. Instead of BAP, Tescera Laboratory composites were polymerized in Tescera inlay oven. All restorations were evaluated according to USPHS criteria during a one-year period. Results: There were no statistically significant differences between direct and indirect composite restorations according to the retention, marginal discoloration, surface staining, proximal contact continuity, and secondary caries. Indirect restorations have less surface roughness, postoperative sensitivity (P < 0.05), and soft tissue irritation (P < 0.1) than direct ones. Conclusion: The clinical performances of the indirect restorations were more satisfactory than the direct restorations.

Temperature Increase Beneath Etched Dentin Discs During Composite Polymerization

OBJECTIVE The purpose of this in vitro study was to measure the temperature increase during the polymerization of a composite resin beneath acid-etched or laser-etched dentin discs. BACKGROUND DATA The irradiation of dentin with an Er:YAG laser may have a positive effect on the thermal conductivity of dentin. This technique has not been studied extensively. MATERIALS AND METHODS Forty dentin discs (5 mm in diameter and 0.5 or 1 mm in height) were prepared from extracted permanent third molars. These dentin discs were etched with 20% orthophosphoric acid or an Er:YAG laser, and were then placed on an apparatus developed to measure temperature increases. The composite resin was polymerized with a high-intensity quartz tungsten halogen (HQTH) or light-emitting diode unit (LED). The temperature increase was measured under the dentin disc with a J-type thermocouple wire that was connected to a data logger. Five measurements were made for each dentin disc, curing unit, and etching system combination. Differences between the initial and the highest temperature readings were taken, and the five calculated temperature changes were averaged to determine the value of the temperature increase. Statistical analysis was performed with a three-way ANOVA and Tukey HSD tests at a 0.05 level of significance. Further SEM examinations were performed. RESULTS The temperature increase values varied significantly, depending on etching systems (p < 0.05), dentin thicknesses (p < 0.05), and curing units (p < 0.05). Temperature increases measured beneath laser-etched discs were significantly higher than those for acid-etched dentin discs (p < 0.05). The HQTH unit induced significantly higher temperature increases than the LED unit (p < 0.05). The LED unit induced the lowest temperature change (5.2°C) in the 1-mm, acid-etched dentin group. The HQTH unit induced the highest temperature change (10.4°C) for the 0.5-mm, laser-etched dentin group. CONCLUSION The risk of heat-induced pulpal damage should be taken into consideration during the polymerization of composite resin after laser etching when the dentin thickness is less than 0.5 mm.

Effect of caries removal techniques on bond strength to caries affected dentin on gingival wall: AFM observation of dentinal surface

Abstract Objective: The purpose of this study was to evaluate the effect of different caries removal techniques on the bond strength of two adhesive systems. Materials and Methods: Seventy human molar teeth that had proximal carious lesions were randomly divided into four groups according to the technique used to remove the caries: a conventional steel bur, an Er:YAG laser, a chemomechanical Carisolv® gel, and air polishing. The groups were then divided into two subgroups according to the adhesives used: Clearfil S3 (Kuraray Co., Ltd, Tokyo, Japan) and Adper SE Plus (3 M ESPE, St Paul, MN, USA). The enamel and superficial dentin of the crown was flattened and caries were removed using different methods. Teeth were restored with composite and three 1 mm2 stick-shaped microtensile specimens were prepared from each tooth. For each removal technique, the surface roughness of one dentin sample was analyzed using atomic force microscopy (AFM). The microtensile bond strength data were then analyzed using a two-way ANOVA, Kruskal–Wallis and Mann–Whitney U tests, and multiple comparison tests (p = 0.05). Results: The two-way ANOVA showed that the effects of the cavity preparation techniques and adhesive systems and their interaction were statistically significant (p < 0.05). The μTBS values were highest when bonding with Adper SE Plus to cavities prepared with the steel bur (37.20 ± 11.65 MPa) and lowest when bonding with Clearfil S3 Bond to cavities prepared with the Er:YAG laser (16.74 ± 6.95 MPa). Conclusion: The caries removal techniques affected the bond strength values of the self-etch adhesive systems.

Evaluation of the effects of different remineralizing agents on Streptococcus mutans biofilm adhesion

Abstract The aim of the study was to compare the effects of different remineralization methods that are well established in clinical and daily use on S. mutans biofilm adhesion. In this study 72 human third molars were used. From each tooth two pieces of 4 mm x 7 mm enamel blocks were acquired. The samples were divided into 6 groups in which include 10 samples per time period (24h and 48 h) and for each remineralization method; control, flouride, ozone, CPP-ACP, arginine, novamin. After remineralization procedures, enamel surfaces were covered with saliva. 105 CFU/mL of active S. mutans culture were inoculated onto the samples. S. mutans colonies were counted with Plate Count Agar (PCA) decimal dilution method. Micromorphologic effects of different remineralization methods were observed by Scanning Electron Microscopy (SEM). The most S. mutans biofilm formation for both time periods was observed in the control group whereas the less biofilm adhesion was showed in the arginine group. There were no statistically significant differences among remineralization agents (p > 0.05). In the control group there was statistical difference between 24 h and 48 h (p < 0.005) but in the other study groups there were no significant difference between the time periods (p > 0.05). Remineralization agents did not significant differ on S. mutans biofilm adhesion.

Effect of laser etching on the fracture strength of the monolithic zirconia and fiber-reinforced composite inlay-retained fixed partial dentures

Abstract Aim: The aim of this study was to evaluate the fracture strength of monolithic zirconia and fiber-reinforced composite (FRC) inlay-retained FPDs, both of which are cemented to the laser-etched cavity surfaces. Materials and Methods: Eighty freshly extracted sound human teeth were used. A premolar and a molar tooth were embedded in an autopolymerizing acrylic resin. Forty acrylic resin models were randomly divided into two groups including monolithic zirconia and FRC inlay-retained FPDs (n = 20). Then, these groups were divided into two subgroups according to conditioning of the cavity surfaces with or without Er:YAG laser etching. Monolithic zirconia inlay-retained FPDs were produced by an inLab MC XL milling device using monolithic zirconia blocks. Tescera™ Fiber Reinforcement Materials were used for the FRC inlay-retained FPDs. After 10.000 thermal cycles, fracture strength test was applied to the specimens. Results: The monolithic zirconia inlay-retained FPDs exhibited the highest fracture strength than the FRC inlay-retained FPDs. Fracture strength was increased with laser etching for both restorative materials (p < 0.05). Conclusion: Laser etching had positively effect on the fracture strength of the inlay-retained FDPs.

Bond strength of repaired composite resins: surface treatments, adhesive systems, and composite type

Abstract The aim of the present study was to investigate the effects of three different surface treatments and two different adhesives on the microtensile bond strength (μTBS) of repaired composites using the same or different type of resin. Twenty-four nano-hybrid (Ceram X mono-C) and 24 nanofilled (Filtek Ultimate-F) composite discs were prepared. The specimens were aged with 5000 thermocycles and randomly divided into groups according to the surface treatment methods: (a) phosphoric acid (b) Er:YAG laser and (c) aluminum trioxide particle (air abrasion). Fresh composite resins (C and F) were added to the treated surfaces with two different adhesives (two-step and one-step self-etch adhesives). Then, the specimens were aged again. The stick-shaped specimens were prepared from the discs (n = 25) and the sticks were subjected to the μTBS test. Results indicated that significant differences were found in μTBS values among the surface treatment methods. In the C groups, the highest μTBS value (41.3 ± 8.3 MPa) was recorded in the air abrasion and one-step self-etch adhesive group, which were repaired with the same kind of composite. In the F groups, the highest μTBS value was observed in the air abrasion and one-step self-etch adhesive (37.6 ± 12.3 MPa) group. The treatment with air abrasion is more effective than the others, and it may be suggested for composite repair.

In vitro evaluation of temperature rise during different post space preparations

Objective: The aim of this study was to evaluate temperature alterations on the outer root surface during post space preparation with six different post drills by using an infrared thermometer. Materials and Methods: Sixty extracted single-rooted human mandibular incisor teeth were used. After root canal obturation, the specimens were divided into six groups (n = 10). During post space preparation, the temperature rises were measured in the middle third of the roots using a noncontact infrared thermometer with a sensitivity of 0.1°C. The temperature data were transferred from the thermometer to the computer and were observed graphically. Results: The maximum temperature rise was observed in Snowpost 2 (29.95 ± 10.2°C) (P < 0.001), but there were no significant differences among Snowpost 2 (29.95 ± 10.2°C), Snowpost 1 (24.6 ± 8.0°C), and Relyx 2 (17.68 ± 9.1°C) (P > 0.05). Conclusions: Although water coolant used, the critical temperature rise was observed on the outer root surface in all post drill systems.