Emmanuelle Bichon

A new reliable sample preparation for high throughput focused steroid profiling by gas chromatography–mass spectrometry

The use of steroid hormones as growth promoters in cattle has been banned within the European Union since 1988 but can still be fraudulently employed in animal breeding farms for anabolic purposes. If an efficient monitoring of synthetic compounds (screening and confirmation) is ensured today by many laboratories, pointing out suspicious samples from a natural steroids abuse remains a tricky challenge due to the difficulty to set relevant threshold levels for these endogenous compounds. The development of focused profiling or untargeted metabolomic approaches is then emerging in this context, with the objective to reveal potential biomarkers signing an exogenous administration of such natural steroids. This study aimed to assess sample preparation procedures based on microextraction and adapt them to high throughput urinary profiling or metabolomic analyses based on gas chromatography-mass spectrometry measurement. Two techniques have been tested and optimised, namely solid phase microextraction (SPME) and microextraction by packed sorbent (MEPS), using five model steroid metabolites (16α-hydroxyandrosterone, 2α-hydroxytestosterone, 11-keto,5β-androstanedione, 6α-hydroxyestradiol and 7β-hydroxypregnenolone). The considered performance criteria included not only the absolute response of the targeted compounds but also the robustness of the materials, and the global aspect of the diagnostic ion chromatograms obtained. After only five successive urinary extractions, a clear degradation of the SPME fiber was observed which led to discard this method as a relevant technique for profiling, whereas no degradation was observed on MEPS sorbent. Repeatability and recovery yields were calculated from urine samples fortified at 500 μg L⁻¹ and extracted by MEPS. They were found respectively below 11% and above 60% for all model compounds. Detection limits were in the 5-15 μg L⁻¹ range depending on the compounds, and a good linearity was observed on the 10-75 μg L⁻¹ range (R² > 0.99). This methodology was applied on urine samples collected from control versus androstenedione-treated bovines, revealing a significant concentration increase for several well-known metabolites such as etiocholanolone, 5α-androstane-3β,17α-diol, 5β-androstane-3α,17α-diol and 5-androstene-3β,17α-diol. Finally, these results allowed to confirm the suitability of the developed strategy and give to this new MEPS application a promising interest in the field of GC-MS based steroid profiling and metabolomic.

Use of isotope ratio mass spectrometry to differentiate between endogenous steroids and synthetic homologues in cattle: a review.

Although substantial technical advances have been achieved during the past decades to extend and facilitate the analysis of growth promoters in cattle, the detection of abuse of synthetic analogs of naturally occurring hormones has remained a challenging issue. When it became clear that the exogenous origin of steroid hormones could be traced based on the (13)C/(12)C isotope ratio of the substances, GC/C/IRMS has been successfully implemented to this aim since the end of the past century. However, due to the costly character of the instrumental setup, the susceptibility of the equipment to errors and the complex and time consuming sample preparation, this method is up until now only applied by a limited number of laboratories. In this review, the general principles as well as the practical application of GC/C/IRMS to differentiate between endogenous steroids and exogenously synthesized homologous compounds in cattle will be discussed in detail, and will be placed next to other existing and to be developed methods based on isotope ratio mass spectrometry. Finally, the link will be made with the field of sports doping, where GC/C/IRMS has been established within the World Anti-Doping Agency (WADA) approved methods as the official technique to differentiate between exogenous and endogenous steroids over the past few years.

Measurement of phthalates diesters in food using gas chromatography–tandem mass spectrometry

An analytical strategy dedicated to 4 major phthalate diesters (DiBP, DnBP, BBzP and DEHP) monitoring in food items has been developed and validated according to normalized guidelines. The method has been applied to a wide range of foodstuffs (n=54) to generate first-ever occurrence data at the French level. This method involves separation and detection using gas chromatography coupled to tandem mass spectrometry, in electron ionisation with highly specific selected reaction monitoring, quantification being performed according to the isotope dilution principle. A particular attention has been paid to background contamination management at any stage of the analytical process, from the sampling to the expression of the results. Limits of reporting, defined as statistically different from background contamination, were found to be 2.7, 0.53, 0.18 and 3.4 μg kg(-1), and relative combined uncertainties were finally found to be 7.6%, 12.2%, 12.0% and 14.1%, for DiBP, DnBP, BBzP and DEHP, respectively.

Molecularly imprinted polymer applied to the selective isolation of urinary steroid hormones: An efficient tool in the control of natural steroid hormones abuse in cattle

The use of anabolic substances to promote growth in livestock is prohibited within the European Union as laid down in Directive 96/22/EC. Nowadays, efficient methods such as steroid profiling or isotopic deviation measurements allow to control natural steroid hormones abuse. In both cases, urine is often selected as the most relevant matrix and, due to its relatively high content of potential interferents, its preparation before analysis is considered as a key step. In this context, the use of a selective sorbent such as molecularly imprinted polymer (MIP) was investigated. A MIP was synthesized based on 17β-estradiol, methacrylic acid and acetonitrile as template, monomer and porogen, respectively. Two approaches were then tested for non-conjugated (aglycons and glucuronides deconjugated) steroid purification: (i) molecularly imprinted solid phase extraction (MISPE) and (ii) semi-preparative supercritical fluid chromatography with a commercial MIP as stationary phase (SFC-MIP). Parameters for both approaches were optimized based on the main bovine metabolites of testosterone, estradiol, nandrolone and boldenone. The MISPE protocol developed for screening purposes allowed satisfactory recoveries (upper 65% for the 12 target steroids) with sufficient purification for gas chromatography-mass spectrometry (GC-MS) analysis. For confirmatory purposes, the use of isotopic ratio mass spectrometry (IRMS) requires a higher degree of purity of the target compounds, which can be reached by the SFC-MIP protocol with three steps less compared to the official and current method. Purity, concentration and absence of isotopic fractionation of target steroids extracted from urine of treated cattle (treated with testosterone, estradiol, androstenedione, and boldenone) allowed the measurement of (13)C/(12)C isotopic ratios of corresponding metabolites and endogenous reference compounds (ERC) and proved the relevance of the strategy.

Chlorination of bisphenol A: Non-targeted screening for the identification of transformation products and assessment of estrogenicity in generated water

Besides the performance of water treatments on the removal of micropollutants, concern about the generation of potential biologically active transformation products has been growing. Thus, the detection and structural elucidation of micropollutants transformation products have turned out to be major issues to evaluate comprehensively the efficiency of the processes implemented for drinking water treatment. However, most of existing water treatment studies are carried out at the bench scale with high concentrations and simplified conditions and thus do not reflect realistic conditions. Conversely, this study describes a non-targeted profiling approach borrowed from metabolomic science, using liquid chromatography coupled to high-resolution mass spectrometry, in order to reveal potential chlorination products of bisphenol A (BPA) in real water samples spiked at 50μgL(-1). Targeted measurements first evidenced a fast removal of BPA (>99%) by chlorination with sodium hypochlorite (0.8mgL(-1)) within 10min. Then, the developed differential global profiling approach enabled to reveal 21 chlorination products of BPA. Among them, 17 were brominated compounds, described for the first time, demonstrating the potential interest of this innovative methodology applied to environmental sciences. In parallel to the significant removal of BPA, the estrogenic activity of water samples, evaluated by ER-CALUX assay, was found to significantly decrease after 10min of chlorination. These results confirm that chlorination is effective at removing BPA in drinking water and they may indicate that the generated compounds have significantly lower estrogenic activity.

Ultra-trace quantification method for chlordecone in human fluids and tissues.

Chlordecone is an organochlorine pesticide (OCP) considered as a Persistent Organic Pollutant (POP) as it persists in the environment, bio-accumulates through the food web, causes adverse effects to human health and the environment and transports across international boundaries far from its sources. The atypical physico-chemical properties of chlordecone make its inclusion in classical analytical approaches non applicable. The aim of our work was to include chlordecone in a multi organochlorine residue method preventing any degradation during the analytical process and thus allowing quantification at ppt (ngkg(-1) or ngL(-1)) levels for a wide range of OCPs in breast milk, human serum and adipose tissue. After GC-HRMS vs. MS/MS and EI vs. APCI comparisons, the major improvement in terms of sensitivity was found in decreasing the length and film thickness of the gas chromatography column. Thanks to a linear correlation between relative response and quantity of chlordecone injected, LC-(ESI-)-MS/MS was finally preferred. An acetonitrile based gradient optimized on a C30 coreshell HPLC column has led to reaching limits of quantification as low as 8ngL(-1), 25pgmL(-1) and 0.2ngg(-1) fat for breast milk, serum and adipose tissue, respectively, allowing multiresidue OCP quantification at concentration levels compatible with biomonitoring purposes and pre-requisites.

Differential chemical profiling to identify ozonation by-products of estrone-sulfate and first characterization of estrogenicity in generated drinking water

For a few years, the concern of water treatment companies is not only focused on the removal of target micropollutants but has been extended to the investigation of potential biologically active by-products generated during the treatment processes. Therefore, some methods dedicated to the detection and structural characterization of such by-products have emerged. However, most of these studies are usually carried out under simplified conditions (e.g. high concentration levels of micropollutants, drastic treatment conditions, use of deionized or ultrapure water) and somewhat unrealistic conditions compared to that implemented in water treatment plants. In the present study, a real field water sample was fortified at the part-per-billion level (50 μg L(-1)) with estrone-3-sulfate (E1-3S) before being ozonated (at 1 mg L(-1)) for 10 min. In a first step, targeted measurements evidenced a degradation of the parent compound (>80%) in 10 min. Secondly, a non-targeted chemical profiling approach derived from metabolomic profiling studies allowed to reveal 11 ozonation by-products, among which 4 were found predominant. The estrogenic activity of these water samples spiked with E1-3S before and after treatment was assessed by the ER-CALUX assay and was found to decrease significantly after 10 min of ozonation. Therefore, this innovative methodological strategy demonstrated its suitability and relevancy for revealing unknown compounds generated from water treatment, and permitted to generate new results regarding specifically the impact of ozonation on estrone-3-sulfate. These results confirm that ozonation is effective at removing E1-3S in drinking water and indicate that the by-products generated have significantly lower estrogenic activity.

Simultaneous determination of 16 brominated flame retardants in food and feed of animal origin by fast gas chromatography coupled to tandem mass spectrometry using atmospheric pressure chemical ionisation

A gas chromatography tandem mass spectrometry method using atmospheric pressure chemical ionisation was developed for the monitoring of 16 brominated flame retardants (7 usually monitored polybromodiphenylethers (PBDEs) and BDE #209 and 8 additional emerging and novel BFRs) in food and feed of animal origin. The developed analytical method has decreased the run time by three compared to conventional strategies, using a 2.5m column length (5% phenyl stationary phase, 0.1mm i.d., 0.1μmf.t.), a pulsed split injection (1:5) with carrier gas helium flow rate at 0.48mLmin(-1) in one run of 20 min. For most BFRs, analytical data were compared with the current analytical strategy relying on GC/EI/HRMS (double sector, R=10000 at 10% valley). Performances in terms of sensitivity were found to meet the Commission recommendation (118/2014/EC) for nBFRs. GC/APCI/MS/MS represents a promising alternative for multi-BFRs analysis in complex matrices, in that it allows the monitoring of a wider list of contaminants in a single injection and a shorter run time.

Simultaneous analysis of historical, emerging and novel brominated flame retardants in food and feed using a common extraction and purification method

Brominated Flame Retardants (BFRs) are still widely used for industrial purposes. These contaminants may enter the food chain where they mainly occur in food of animal origin. The aim of our work was to provide a unique method able to quantify the widest range of BFRs in feed and food items. After freeze-drying and grinding, a pressurized liquid extraction was carried out. The extract was purified on acidified silica, Florisil® and carbon columns, the four separated fractions were analyzed by gas and liquid chromatography coupled to high resolution and tandem mass spectrometry. Isotopic dilution was preferentially used when commercial labelled compounds were available. Analytical sensitivity was in accordance with the expectations of Recommendation 2014/118/EU for PBDEs, HBCDDs, TBBPA, TBBPA-bME, EHTBB, BEHTEBP and TBBPA-bME. Additional BFRs were included in this analytical method with the same level of performances (LOQs below 0.01 ng g-1 ww). These are PBBs, pTBX, TBCT, PBBz, PBT, PBEB, HBBz, BTBPE, OBIND and T23BPIC. However, some of the BFRs listed in Recommendation 2014/118/EU are not yet covered by our analytical method, i.e. TBBPA-bOHEE, TBBPA-bAE, TBBPA-bGE, TBBPA-bDiBPrE, TBBPS, TBBPS-bME, TDBPP, EBTEBPI, HBCYD and DBNPG. The uncertainty measurement was fully calculated for 21 of the 31 analytes monitored in the method. Reproducibility uncertainty was below 23% in isotopic dilution. Certified reference materials are now required to better characterize the trueness of this method, which was applied in the French National Control Plans.

Past and recent state of sediment contamination by persistent organic pollutants (POPs) in the Rhône River: Overview of ecotoxicological implications

Twenty-one sediment samples were taken from five dated sediment cores collected along the Rhône River from 2008 to 2011. A total of 17 polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), 7 polychlorinated biphenyls (PCBs), 8 polybrominated diphenyl ethers (PBDEs), 3 polybrominated biphenyls (PBBs), 3 hexabromocyclododecanes (HBCD) and 31 organochlorine pesticides (OCPs) were investigated to provide information on deposition dynamics in time and space, but also regarding the ecotoxicological risks associated with these contaminants. Median concentrations of total PBDEs are nine times lower than the levels of total PCBs along the entire studied stretch of the Rhône River. The results show that total PBDEs concentrations range from 0.06 to 239 μg·kg-1 DW with a median value of 3.81 μg·kg-1 DW and a maximum concentration measured in the years 2000s. These maximum concentrations are identical to those measured for total PCBs at the end of the 1990s, but show a different pattern of distribution. Abnormal dichlorodiphenyltrichloroethane (DDT) levels were also detected in the downstream section of the river, with a peak concentration of 147.5 μg·kg-1 DW measured at the GEC site from 2005 onwards. Analyses of the enantiomeric fractions reveal a fresh input resulting from a technical formulation. Sediments from the core sampled at the most downstream site (GEC) are found to be highly toxic to organisms living nearby, particularly because of the total PCDD/Fs, DDE and DDT levels. In addition, based on available sediment quality guidelines, there may be a potential bioaccumulation risk for humans not only for these three compounds of concern but also for total PCBs and 7 out of the 8 analysed PBDEs.