Enrique Antonio-Lopez

Hole-Assisted Few-Mode Multicore Fiber for High-Density Space-Division Multiplexing

A seven-core few-mode multicore fiber in which each core supports both the LP01 mode and the two degenerate LP11 modes has been designed and fabricated for the first time, to the best of our knowledge. The hole-assisted structure enables low inter-core crosstalk and high mode density at the same time. LP01 inter-core crosstalk has been measured to be lower than -60 dB/km. LP11 inter-core crosstalk has been measured to be around -40 dB/km using a different setup. The LP11 free-space excitation-induced crosstalk is simulated and analyzed. This fiber allows multiplexed transmission of 21 spatial modes per polarization per wavelength. Data transmission in LP01/LP11 mode over 1 km of this fiber has been demonstrated with negligible penalty.

Optimization of multicore fiber for high-temperature sensing.

We demonstrate a novel high-temperature sensor using multicore fiber (MCF) spliced between two single-mode fibers. Launching light into such fiber chains creates a supermode interference pattern in the MCF that translates into a periodic modulation in the transmission spectrum. The spectrum shifts with changes in temperature and can be easily monitored in real time. This device is simple to fabricate and has been experimentally shown to operate at temperatures up to 1000°C in a very stable manner. Through simulation, we have optimized the multicore fiber design for sharp spectral features and high overall transmission in the optical communications window. Comparison between the experiment and the simulation has also allowed determination of the thermo-optic coefficient of the MCF as a function of temperature.

Ultrasensitive vector bending sensor based on multicore optical fiber

In this Letter, we demonstrate a compellingly simple directional bending sensor based on multicore optical fibers (MCF). The device operates in reflection mode and consists of a short segment of a three-core MCF that is fusion spliced at the distal end of a standard single mode optical fiber. The asymmetry of our MCF along with the high sensitivity of the supermodes of the MCF make the small bending on the MCF induce drastic changes in the supermodes, their excitation, and, consequently, on the reflected spectrum. Our MCF bending sensor was found to be highly sensitive (4094  pm/deg) to small bending angles. Moreover, it is capable of distinguishing multiple bending orientations.

10 Spatial mode transmission using low differential mode delay 6-LP fiber using all-fiber photonic lanterns.

To unlock the cost benefits of space division multiplexing transmission systems, higher spatial multiplicity is required. Here, we investigate a potential route to increasing the number of spatial mode channels within a single core few-mode fiber. Key for longer transmission distances and low computational complexity is the fabrication of fibers with low differential mode group delays. As such in this work, we combine wavelength and mode-division multiplexed transmission over a 4.45 km low-DMGD 6-LP-mode fiber by employing low-loss all-fiber 10-port photonic lanterns to couple light in and out of the fiber. Hence, a minimum DMGD of 0.2 ns (maximum 0.357 ns) is measured after 4.45 km. Instrumental to the multi-mode transmission system is the employed time-domain-SDM receiver, allowing 10 spatial mode channels (over both polarizations) to be captured using only 3 coherent receivers and real-time oscilloscopes in comparison with 10 for conventional methods. The spatial channels were unraveled using 20 × 20 multiple-input multiple-output digital signal processing. By employing a novel round-robin encoding technique, stable performance over a long measurement period demonstrates the feasibility of 10x increase in single-core multi-mode transmission.

Strong Bragg Gratings in Highly Photosensitive Photo-Thermo-Refractive-Glass Optical Fiber

A new type of photosensitive fiber is demonstrated. Long lengths (>;100 m) of coreless optical fiber are fabricated from highly photosensitive photo-thermo-refractive glass. A minimum loss of <;2 dB/m is measured. A holographic technique using low power near-UV two-beam interference patterns is applied to record strong and robust Bragg gratings inside the fiber. The gratings show no degradation when heated up to 425 °C for several hours.

1 km hole-assisted few-mode multi-core fiber 32QAM WDM transmission

24.3GBaud 32QAM WDM transmission over a novel 1km hole-assisted few-mode multi-core fiber is demonstrated, resulting in 5.1Tbit/s spatial supercarriers (4Tbit/s net) with a gross spectral efficiency of 102bits/s/Hz, and a gross aggregate transmission rate of 255 Tbit/s (200 Tbit/s net).

Accurate Strain Sensing Based On Super-Mode Interference In Strongly Coupled Multi-Core Optical Fibres

We report on the use of a multi-core fibre (MCF) comprising strongly-coupled cores for accurate strain sensing. Our MCF is designed to mode match a standard single mode optical fibre. This allows us to fabricate simple MCF interferometers whose interrogation is carried out with light sources, detectors and fibre components readily available from the optical communications tool box. Our MCF interferometers were used for sensing strain. The sensor calibration was carried out in a high-fidelity aerospace test laboratory. In addition, a packaged MCF interferometer was transferred into field trials to validate its performance under deployment conditions, specifically the sensors were installed in a historical iron bridge. Our results suggest that the MCF strain sensors here proposed are likely to reach the readiness level to compete with other mature sensor technologies, hence to find commercial application. An important advantage of our MCF interferometers is their capability to operate at very high temperatures.

Miniature multicore optical fiber vibration sensor

We demonstrate a compact and versatile interferometric vibration sensor that operates in reflection mode. To build the device, a short segment of symmetric strongly coupled multicore optical fiber (MCF) is fusion spliced to a single-mode optical fiber (SMF). One end of the MCF segment is cleaved and placed in a cantilever position. Due to the SMF-MCF configuration, only two supermodes are excited in the MCF. Vibrations induce cyclic bending of the MCF cantilever which results in periodic oscillations of the reflected interference spectrum. In our device, the MCF itself is the inertial mass. The frequency range where our device is sensitive can be easily tailored from a few hertz to several kilohertz through the cantilever dimensions.

Interferometer based on strongly coupled multi-core optical fiber for accurate vibration sensing

We report on the use of a simple interferometer built with strongly-coupled core optical fiber for accurate vibration sensing. Our multi-core fiber (MCF) is designed to mode match a standard single-mode optical fiber (SMF). The interferometer consists of a low insertion loss SMF-MCF-SMF structure where only two super-modes interfere. The polymer coating of the MCF was structured and the interferometer was sandwiched between a flat piece and a V-groove. In this manner our device is highly sensitive to force with sensitivity reaching -4225 pm/N. To make the MCF interferometer sensitive to vibrations the flat piece was allowed to move, thus, its periodic movements exert cyclic localized pressure on the MCF which makes the interference pattern to shift periodically. Our sensors can be used to monitor vibrations in a broad frequency range with the advantage that the measurements are unaffected by temperature changes.

16QAM SDM-WDM Transmission over a Novel Hole-Assisted Few-Mode Multi-Core Fiber

A gross transmission rate of 204 Tbit/s is demonstrated over a novel 1 km hole-assisted step-index few-mode multi-core fiber with 7 cores, where each core allows the co-propagation of 3 spatial modes.