Erica Block

Simultaneous spatial and temporal focusing for tissue ablation

Simultaneous spatial and temporal focusing (SSTF) of femtosecond pulses was originally conceived as a novel method for increasing the field-of-view in multiphoton imaging applications. Multiphoton imaging with SSTF deviated from traditional nonlinear systems in that it enabled the use of low numerical aperture beams to be used to increase the field-of-view, but retain the axial sectioning of a high numerical aperture beam. In this manner efficiency gains in the imaging process were achieved without compromising axial resolution [1,2].

INTEGRATED SINGLE GRATING COMPRESSOR FOR VARIABLE PULSE-FRONT TILT IN SIMULTANEOUSLY SPATIALLY AND TEMPORALLY FOCUSED SYSTEMS

A Ti:Al(3)O(2) multipass chirped pulse amplification system is outfitted with a single-grating, simultaneous spatial and temporal focusing (SSTF) compressor platform. For the first time, this novel design has the ability to easily vary the beam aspect ratio of an SSTF beam, and thus the degree of pulse-front tilt at focus, while maintaining a net zero-dispersion system. Accessible variation of pulse front tilt gives full spatiotemporal control over the intensity distribution at the focus and could lead to better understanding of effects such as nonreciprocal writing and SSTF-material interactions.

Simultaneously spatially and temporally focusing light for tailored ultrafast micro-machining

Simultaneous spatially and temporally focussing (SSTF) of ultrashort pulses allows for an unprecedented control of the intensity distribution of light. It has therefore a great potential for widespread applications ranging from nonlinear microscopy, ophthalmology to micro-machining. SSTF also allows to overcome many bottlenecks of ultrashort pulse micro-machining, especially non-linear effects like filamentation and self-focussing. Here, we describe and demonstrate in detail how SSTF offers an additional degree of freedom for shaping the focal volume. In order to obtain a SSTF beam, the output of an ultrafast laser is usually split by a grating into an array of copies of the original beam, which we refer to as beamlets. The ratio of the beamlet array width to the width of the invidual beamlet is the beam aspect ratio. The focal volume of the SSTF beam can now be tailored transversally by shaping the cross-section of the beamlets and axially by choosing the right beam aspect ratio. We will discuss the requirements of the setup for a successful implementation of this approach: Firstly, the group velocity dispersion and the third order dispersion have to be compensated in order to obtain a high axial confinement. Secondly, the beamlet size and their orientation should not vary too much spectrally. Thirdly, beamlet and SSTF focus should match. We will hence demonstrate how SSTF allows to inscribe tailored three-dimensional structures with fine control over their aspect ratio. We also show how the SSTF focus can be adapted for various glasses and crystals.

Spatial–spectral characterization of focused spatially chirped broadband laser beams

Proper alignment is critical to obtain the desired performance from focused spatially chirped beams, for example in simultaneous spatial and temporal focusing (SSTF). We present a simple technique for inspecting the beam paths and focusing conditions for the spectral components of a broadband beam. We spectrally resolve the light transmitted past a knife edge as it was scanned across the beam at several axial positions. The measurement yields information about spot size, M2, and the propagation paths of different frequency components. We also present calculations to illustrate the effects of defocus aberration on SSTF beams.

Simultaneous spatial frequency modulation imaging and micromachining with a femtosecond laser.

A Ti:Al2O3 chirped-pulse amplification system is used to simultaneously image and machine. By combining simultaneous spatial and temporal focusing (SSTF) with spatial frequency modulation for imaging (SPIFI), we are able to decouple the imaging and cutting beams to attain a resolution and a field-of-view that is independent of the cutting beam, while maintaining single-element detection. This setup allows for real-time feedback with the potential for simultaneous nonlinear imaging and imaging through scattering media. The novel SSTF machining platform uses refractive optics that, in general, are prohibitive for energetic, amplified pulses that might otherwise compromise the integrity of the focus as a result of nonlinear effects.

Highly localized plasma formation in air using space-time cusing of mJ ultrafast pulses

Space-time focusing of spatially-chirped Ti:Sapphire laser pulses is used to generate a plasma in air axially localized to 28× less than the confocal parameter, suppressing filamentation on the way to the focus.

High-speed two-dimensional multiphoton microscope using spatial modulation

We demonstrate, for the first time, a multimodal multiphoton microscope using chirped intensity modulation to construct line images from a single element detector.

Intuitive analysis of space-time focusing with double-ABCD calculation

We analyze the structure of space-time focusing of spatially-chirped pulses using a technique where each frequency component of the beam follows its own Gaussian beamlet that in turn travels as a ray through the system.