Fabrizio Memola Capece Minutolo

Selective Laser Post-Treatment on Titanium Cold Spray Coatings

The aim of the present work is to investigate the feasibility and effects of a selective postdeposition laser treatment on titanium coatings. Commercially pure titanium grade 2 powders were deposited by means of a cold spray process on aluminum alloy AA2024-T3 sheets. The surface treatment of the coating was realized using a 220 W diode laser. The influence of heat input and dimensional features of coating layer and substrate was assessed by an experimental campaign conducted following a design of experiments approach. Optical and scanning electron microscopy analysis of the microstructure of the deposited and treated material as well as microhardness measurements showed the formation of a compact layer of titanium oxide on the coating surface and the preservation of the temper state of the aluminum substrate.

Ti-6Al-4V Cutting by 100W Fibre Laser in Both CW and Modulated Regime

Titanium and its alloys are nowadays widely used in many sectors: in the medical field (orthopedic and dental ones), in the architectural field, in the chemical plants field and in aeronautic [1]. In this last field it is more and more used both for its contribution to make lightweight and time durable structures and for its compatibility with new materials, first of all Carbon Fiber Reinforced Plastics (CFRP). Cutting of titanium sheets is one of the primary requirements in the fabrication of most of the components. Laser cutting offers several advantages over conventional cutting methods. It includes narrow kerf width (minimum material lost), straight cut edges, low roughness of cut surfaces, minimum metallurgical and surface distortions, easy integration with computer numerically controlled (CNC) machines for cutting complex profiles and importantly non-contact nature of the process (suitable for cutting in hostile environments and in areas with limited access) [2]. However, due to very limited literature available on laser cutting of titanium, it is very difficult to predict the cut surface quality and optimum process parameters for laser cutting, especially when dross-free cuts are required. Laser cutting of titanium and titanium alloys needs to be carried out with an inert gas, this due to the high reactivity of the titanium with the oxygen at high temperatures [3]. However when the available power is limited, as in the present case, the use of a reactive gas (air) can help to achieve cutting speed value reasonable for industrial applications. The aim of this work is to study the cutting of Ti-6Al-4V rolled sheets 1 mm in thickness, by means of a 100 W fibre laser, (SPI-Red Power) working at wavelength  = 1090 nm. The maximum cutting speed were measured in both CW and pulsed regime at different mean power and different duration. Furthermore, the kerf geometry and the heat affected zone (HAZ) were studied decreasing the cutting speed from the maximum to the 80 % of this values. The results obtained showed that both the power and the cutting speed influence the cutting kerf geometry and HAZ. In particular the synergy of power and speed, resulting roughly into the heat input, seems to rule the whole cutting process.

Laser Cutting of Aluminium Sheets with a Superficial Cold Spray Titanium Coating

In the manufacturing of metal components both wear and corrosion have to be considered. In particular, corrosion is a primary problem in the aeronautic field, where the aluminium alloys are affected by several corrosion typologies. Furthermore, nowadays carbon fibre reinforced plastics (CFRP) are finding an increasing use, but they can induce galvanic corrosion phenomena when coupled with aluminium alloys. To overcome this problem, corrosion resistant coatings are used on aluminium components. On these premises, the realization of a titanium coating on aluminium components could allow the coupling of CFRP and aluminium alloys, improving the corrosion resistance. Cold Spray Deposition is a recent technology to realize these coatings. This technology allows the production of near fully dense coatings on metallic surfaces. In many applications the coated aluminium sheets have to be machined (cut or drilled). Machining with conventional cutting methods leads to both tool wear and damages in the coating. Laser cutting represents a promising alternative: it does not involve any mechanical cutting force or tool wear and, thanks to the small laser beam spot, it allows to realize complex shapes. In this paper, laser cutting of an Al alloy sheet (0.6 mm thick) coated with Ti Alloy, was studied. The adopted laser source was a 150 W, lamp pumped Nd:YAG, specifically developed for micro-machining operations on metals. During the tests, the process parameters (cutting speed, pulse duration and entrance side) were changed and the kerf geometry was analysed as a function of the process parameters.

Experimental Study on the Incremental Forming of Coated Aluminum Alloy Sheets

Superficial coatings are widely used in industrial applications in order to improve the superficial properties of metallic components. In particular, in the aeronautic field, all the components are coated in order to prevent both corrosion and wear. In this field, heat treatable aluminum alloys, in age hardened condition, are used; consequently, superficial coatings must be carried out through “cold” processes, i.e. coating processes in which the component to be coated remains at low temperatures, below 100°C. Cold gas dynamic spray technique (CGDS) is a process of deposition that consists in the realization of surface coatings with high-velocity metal particles sprayed on the substrate at temperature significantly lower than the melting one of the substrate itself and at relatively low temperatures if compared to other spray techniques. When processing conditions are optimized, the process can produce near fully dense coatings. This technique could be particularly useful in the coating of rolled sheets, needing of successive cold plastic deformations. One of the cold plastic processes is incremental forming, a high flexible process for rapid manufacturing of complex sheet metal part shapes; it presents the potential to be easy to automate and particularly attractive for small batches and customized parts. In this process, a simple tool describes a path that allows to locally deform the sheet clamped along its periphery. The aim of this paper is to study the evolution and behaviour of aluminum coating deposed by CGDS on AA 2024-T3 sheets carried out by an incremental forming process. This evaluation is carried out by characterizing the cold sprayed coating after the forming process for different wall angles of simples geometries.

Formability and Surface Quality of Incrementally Formed Grade 1 Titanium Thin Sheets

The incremental forming of titanium alloy sheets combines the advantages of this advanced flexible manufacturing process, that allows to produce complex components without using dedicated tools, with the interesting properties of the material under consideration. In this study, thin sheets of grade 1 titanium were incrementally formed to evaluate their formability and surface quality by varying the tool-sheet contact conditions. Experimental tests and surface analyses highlight dependence on the contact conditions of the surface quality rather than of the formability. Moreover, they emphasize that the tool-sheet contact conditions mainly affect the repeatability of the process due to the occurrence of galling.

Effect of the process parameters on the geometrical defects of Ti-6Al-4V hot rolled sheets laser beam welded

Ti-6Al-4V is an alloy that is increasingly used in aeronautics due to its high mechanical properties coupled with the lightness. An effective technology used to manufacture titanium components with a reduced buy to fly ratio is the laser beam welding. Previous studies showed that the key factor that rules the mechanical properties and the fatigue life of the joint is its morphology. The aim of this paper was to investigate the influence of the main process parameters, such as welding speed and laser power, on the geometrical features of the joint, in terms of undercut, underfill, reinforcement and so on. 3.0 mm thick Ti-6Al-4V rolled sheets were welded in butt joint configuration by using a Nd-YAG laser source. The joint performances were studied in terms of weld morphology, microstructure and Vickers microhardness. Then, defects such as underfill and reinforcement, controlling the whole weld morphology, were observed, and the relationship between the occurrence, the entity of these defects and the process parameters was studied.

Wear Behavior of WC-Co Carbides with Addition of Cr3C2 and Ni

Cemented carbides present some characteristics that ensure high performances for cutting and wear-resistant tools. The aim of the work is to evaluate the influence of Chromium Carbide and Nickel on the properties (wear and friction) of a cemented carbide constituted by a hard phase of tungsten carbide and a binder phase of cobalt. Different tests were carried out by varying the percentage of Cr3C2 and, for one only case, also Nickel was added. The tests were carried out by a pin-on-disk apparatus and diamond abrasive sheet. The experimental campaign provided tests for different values of load and relative velocity. Friction coefficient was directly evaluated by the apparatus and data on the wear were obtained by measuring the loss of weight of the samples (parallelepipeds with hemispherical head). The tests allowed to determine the percentage of Cr3C2 that ensure an improvement of the aforementioned properties and to highlight the irrelevance of Nickel.