Farasat Iqbal

Evaluation of electrical, dielectric and magnetic characteristics of Al–La doped nickel spinel ferrites

The paper reports the effects of lanthanum and aluminum ions, on the structural, electrical and magnetic properties of NiFe2O4 spinel ferrite nanoparticles. The precursors have been synthesized via a hydrothermal route in the presence of ascorbic acid (AA) using urea as a reducing agent and fuel for maintaining the uniform morphology and equal particle size distribution. In order to find out the optimum temperature (1023 K) for the formation of the spinel phase of the doped nickel ferrite, thermogravimetric analysis (TGA) for the un-annealed samples was performed. The X-ray diffraction patterns show that NiFe2−2xAlxLaxO4 have been well crystallized to spinel ferrite crystal structure with the Fd3m space group. The average crystallite size obtained is in the range of 9–19 nm, a size useful for attaining a suitable signal-to-noise ratio in high-density recording media and in electrical devices. In order to render the synthesized samples for diminishing eddy current losses, we were able to enhance the room temperature resistivity through proper selection of dopant used. The dielectric constant and dielectric loss decreased with applied frequency for all the samples showing normal behavior of ferrites. The calculated magnetic parameters such as saturation magnetization (Ms), remanence (Mr) and coercivity (Hc), showed increased values for some Al–La doped samples.

Chitosan/hydroxyapatite (HA)/hydroxypropylmethyl cellulose (HPMC) spongy scaffolds-synthesis and evaluation as potential alveolar bone substitutes

Alveolar bone loss is associated with infections and its augmentation is a pre-requisite for the success of dental implants. In present study, we aim to develop and evaluate novel freeze dried doxycycline loaded chitosan (CS)/hydroxyapatite (HA) spongy scaffolds where hydroxypropylmethyl cellulose (HPMC) was added as a crosslinker. Scaffolds displayed compressive strength of 14MPa/cm3 and 0.34 as elastic response. The interconnected pore diameter was 41-273μm, favorably provided the template supporting cells and transport. An overall 10% degradation was seen after 14days studies at pH 7.4 in PBS. Doxycycline hyclate, a frequently used drug to counter oral infections, demonstrated an initial burst release (6-8h), followed by a sustain release profile for the remaining 64h. CS/HA/HPMC scaffolds were nontoxic and promoted pre-osteoblast cell viability as seen with live/dead calcein staining after 24h where scaffolds with 10% and 25% HPMC by weight of scaffold had more viable cells. Scaffolds with 10%, 20% and 25% HPMC by weight of scaffold showed efficient cellular adhesion as seen in scanning electron microscopy images (day 8) indicating that pre-osteoblast cells were able to adhere well on the surface and into the porous structure via cytoplasmic extensions. Hoechst 33258 nuclear staining at day 2 and 8 indicated cell proliferation which was further supported byMTT assay at day 2, 4 and 8. Although all scaffolds supported pre-osteoblast cell viability, alkaline phosphatase (ALP) staining demonstrated that upon induction, differentiation was pronounced in case of scaffolds with 10% HMPC scaffolds. Conclusively, these materials having all the required mechanical and biological properties are potential candidates for alveolar bone regeneration.

Effect of calcium hydroxide on mechanical strength and biological properties of bioactive glass.

In this manuscript for the first time calcium hydroxide (Ca(OH)2) has been used for preparation of bioactive glass (BG-2) by co-precipitation method and compared with glass prepared using calcium nitrate tetrahydrate Ca(NO3)2·4H2O (BG-1), which is a conventional source of calcium. The new source positively affected physical, biological and mechanical properties of BG-2. The glasses were characterized by Fourier transform infrared (FTIR), X-Ray Diffractometer (XRD), Scanning Electron Microscopy (SEM), Thermogravimetric Analysis/Differential Scanning Calorimetry (TGA-DSC), BET surface area analysis and Knoop hardness. The results showed that BG-2 possessed relatively larger surface properties (100m(2)g(-1) surface area) as compared to BG-1 (78m(2)g(-1)), spherical morphology and crystalline phases (wollastonite and apatite) after sintering at lower than conventional temperature. These properties contribute critical role in both mechanical and biological properties of glasses. The Knoop hardness measurements revealed that BG-2 possessed much better hardness (0.43±0.06GPa at 680°C and 2.16±0.46GPa at 980°C) than BG-1 (0.24±0.01 at 680°C and 0.57±0.07GPA at 980°C) under same conditions. Alamar blue Assay and confocal microscopy revealed that BG-2 exhibited better attachment and proliferation of MG63 cells. Based on the improved biological properties of BG-2 as a consequent of novel calcium source selection, BG-2 is proposed as a bioactive ceramic for hard tissue repair and regeneration applications.

Hydroxypropylmethyl cellulose (HPMC) crosslinked chitosan (CH) based scaffolds containing bioactive glass (BG) and zinc oxide (ZnO) for alveolar bone repair

The success of a dental implant relies on the presence of an optimal alveolar ridge. The aim of this study was to fabricate HPMC crosslinked chitosan based scaffolds for alveolar bone repair. Our results indicated that HPMC crosslinked CH/BG foams presented better morphological structure (132-90.5 μm) and mechanical responses (0.451 MPa with 100 mg BG) as confirmed by SEM analysis and fatigue testing respectively. Cytotoxicity analysis at day 2, 4 and 8 demonstrated that all composites were non-toxic and supported cellular viability. Calcein AM/propidium iodide staining, Hoechst nuclear staining and cell adhesion assay reiterated that scaffolds supported pre-osteoblast cell growth, adhesion and proliferation. Differentiation potential of pre-osteoblast cells was enhanced as confirmed by alkaline phosphate assay. Furthermore, loss of S. aureus viability as low as 35% was attributed to synergistic effects of components. Overall, our results suggest that HPMC crosslinked scaffolds are potential candidates for alveolar bone repair.

Ionic liquid as a potential solvent for preparation of collagen-alginate-hydroxyapatite beads as bone filler

Abstract In this study, collagen/alginate/hydroxyapatite beads having different proportions were prepared as bone fillers for the restoration of osteological defects. Ionic liquid was used to dissolve the collagen and subsequently the solution was mixed with sodium alginate solution. Hydroxyapatite was added in different proportions, with the rationale to enhance mechanical as well as biological properties. The prepared solutions were given characteristic bead shapes by dropwise addition into calcium chloride solution. The prepared beads were characterized using FTIR, XRD, TGA and SEM analysis. Microhardness testing was used to evaluate the mechanical properties. The prepared beads were investigated for water adsorption behavior to ascertain its ability for body fluid uptake and adjusted accordingly to the bone cavity. Drug loading and subsequently the antibacterial activity was investigated for the prepared beads. The biocompatibility was assessed using the hemolysis testing and cell proliferation assay. The prepared collagen-alginate-HA beads, having biocompatibility and good mechanical properties, have showed an option of promising biologically active bone fillers for bone regeneration.