Farzaneh F. Jebrail

About mean diameter and size distributions of poly(lactide-co-glycolide) (PLG) microspheres

Despite the importance of microsphere size for controlled drug delivery, little work has been done to quantitatively predict the distribution of microspheres from manufacturing techniques. This work presents a quantitative study that describes the size distribution of poly(lactide-co-glycolide) (PLG) microspheres. A fluid mechanics based correlation for the mean microsphere diameter is formulated based on the theory of emulsification in turbulent flow under non-coalescing conditions. The correlation was constructed and validated with experimentally obtained mean microsphere diameters prepared at different stirring speeds. In addition, a Rosin Rammler distribution function was found to give an accurate representation of the microsphere distribution. The spread of the microsphere size distribution was found to decrease with stirring speed. With the validation of the mathematical correlation, it is now possible to have a good estimate of the average microsphere size prior to microsphere preparation. This is directly relevant to the pharmaceutical industry where microspheres of specified mean diameter and size distribution are desirable.

On the mechanical properties of bovine serum albumin (BSA) adhesives.

Biological adhesives, natural and synthetic, are of current active interest. These adhesives offer significant advantages over traditional sealant techniques, in particular, they are easier to use, and can play an integral part in the healing mechanism of tissue. Thus, biological adhesives can play a major role in medical applications if they possess adequate mechanical behavior and stability over time. In this work, we report on the method of preparation of bovine serum albumin (BSA) into a biological adhesive. We present quantitative measurements that show the effect of BSA concentration and cross-linker content on the bonding strength of BSA adhesive to wood. A comparison is then made with synthetic poly(glycidyl methacrylate) (PGMA) adhesive, and a commercial cyanoacrylate glue, which was used as a control adhesive. In addition, BSA samples were prepared and characterized for their water content, tensile strength, and elasticity. We show that on dry surface, BSA adhesive exhibits a high bonding strength that is comparable with non-biological commercial cyanoacrylate glues, and synthetic PGMA adhesive. Tensile testing on wet wood showed a slight increase in the bonding strength of BSA adhesive, a considerable decrease in the bonding strength of cyanoacrylate glue, and negligible adhesion of PGMA. Tests performed on BSA samples demonstrate that initial BSA concentration and final water content have a significant effect on the stress–strain behavior of the samples.

Buoyancy driven mixing of miscible fluids by volumetric energy deposition of microwaves.

Abstract An experiment that seeks to investigate buoyancy driven mixing of miscible fluids by microwave volumetric energy deposition is presented. The experiment involves the use of a light, non-polar fluid that initially rests on top of a heavier fluid which is more polar. Microwaves preferentially heat the polar fluid, and its density decreases due to thermal expansion. As the microwave heating continues, the density of the lower fluid eventually becomes less than that of the upper, and buoyancy driven Rayleigh-Taylor mixing ensues. The choice of fluids is crucial to the success of the experiment, and a description is given of numerous fluid combinations considered and characterized. After careful consideration, the miscible pair of toluene / tetrahydrofuran (THF) was determined as having the best potential for successful volumetric energy deposition buoyancy driven mixing. Various single fluid calibration experiments were performed to facilitate the development of a heating theory. Thereafter, results from two-fluid mixing experiments are presented that demonstrate the capability of this novel Rayleigh-Taylor driven experiment. Particular interest is paid to the onset of buoyancy driven mixing and unusual aspects of the experiment in the context of typical Rayleigh-Taylor driven mixing.

Fabrication and characterisation of 2NDPA-loaded poly(lactide-co-glycolide) (PLG) microspheres for explosive safety.

We demonstrate the microencapsulation of a double-base (DB) rocket propellant stabiliser, 2-nitrodiphenylamine (2-NDPA), that can potentially increase the shelf life of DB rocket propellants. Poly(lactide-co-glycolide) (PLG) microspheres loaded with 2-NDPA were prepared using the oil-in-water emulsion technique. The microsphere size was found to be inversely related to the mixing rate. It was also found that a higher theoretical loading of 2-NDPA resulted in larger microspheres. In addition, a Rosin Rammler distribution function gave an accurate representation of the microsphere size distribution, and the release rate 2-NDPA from PLG microspheres was found to be size dependent. We show that parameters such as the stirring speed and the percent loading of 2-NDPA can be varied to tailor the release of 2-NDPA from PLG microspheres. In addition, we have shown that temperature has a dramatic effect on the release of 2-NDPA from PLG microcapsules.