Florian Bruckner

3D print of polymer bonded rare-earth magnets, and 3D magnetic field scanning with an end-user 3D printer

3D print is a recently developed technique, for single-unit production, and for structures that have been impossible to build previously. The current work presents a method to 3D print polymer bonded isotropic hard magnets with a low-cost, end-user 3D printer. Commercially available isotropic NdFeB powder inside a PA11 matrix is characterized, and prepared for the printing process. An example of a printed magnet with a complex shape that was designed to generate a specific stray field is presented, and compared with finite element simulation solving the macroscopic Maxwell equations. For magnetic characterization, and comparing 3D printed structures with injection molded parts, hysteresis measurements are performed. To measure the stray field outside the magnet, the printer is upgraded to a 3D magnetic flux density measurement system. To skip an elaborate adjusting of the sensor, a simulation is used to calibrate the angles, sensitivity, and the offset of the sensor. With this setup, a measurement resolut...

Heat-assisted magnetic recording of bit-patterned media beyond 10 Tb/in2

The limits of areal storage density that is achievable with heat-assisted magnetic recording are unknown. We addressed this central question and investigated the areal density of bit-patterned media. We analyzed the detailed switching behavior of a recording bit under various external conditions, allowing us to compute the bit error rate of a write process (shingled and conventional) for various grain spacings, write head positions, and write temperatures. Hence, we were able to optimize the areal density yielding values beyond 10 Tb/in2. Our model is based on the Landau-Lifshitz-Bloch equation and uses hard magnetic recording grains with a 5-nm diameter and 10-nm height. It assumes a realistic distribution of the Curie temperature of the underlying material, grain size, as well as grain and head position.

Magnetoelastic resonance sensor for remote strain measurements

A low cost passive wireless strain sensor is proposed. The basis of the sensor is formed by two softmagnetic magnetostrictive ribbons. The first magnetostrictive ribbon transforms mechanical stress into a stress dependent magnetic field. The second ribbon senses this field by magnetoacoustic oscillations. The resonance frequency directly depends on the applied mechanical stress. For the proposed sensor, a gauge factor Gf, which is defined as the relative change of the resonance frequency divided by the strain ɛ, of Gf = 380 is obtained. This is significantly higher than the gauge factor of standard metal foil strain gages.

Calculation of coercivity of magnetic nanostructures at finite temperatures

We report a finite temperature micromagnetic method (FTM) that allows for the calculation of the coercive field of arbitrary shaped magnetic nanostructures at time scales of nanoseconds to years. Instead of directly solving the Landau-Lifshitz-Gilbert equation, the coercive field is obtained without any free parameter by solving a non linear equation, which arises from the transition state theory. The method is applicable to magnetic structures where coercivity is determined by one thermally activated reversal or nucleation process. The method shows excellent agreement with experimentally obtained coercive fields of magnetic nanostructures and provides a deeper understanding of the mechanism of coercivity.

Multiscale modeling in micromagnetics: Existence of solutions and numerical integration

Various applications ranging from spintronic devices, giant magnetoresistance sensors, and magnetic storage devices, include magnetic parts on very different length scales. Since the consideration of the Landau–Lifshitz–Gilbert equation (LLG) constrains the maximum element size to the exchange length within the media, it is numerically not attractive to simulate macroscopic parts with this approach. On the other hand, the magnetostatic Maxwell equations do not constrain the element size, but cannot describe the short-range exchange interaction accurately. A combination of both methods allows one to describe magnetic domains within the micromagnetic regime by use of LLG and also considers the macroscopic parts by a nonlinear material law using the Maxwell equations. In our work, we prove that under certain assumptions on the nonlinear material law, this multiscale version of LLG admits weak solutions. Our proof is constructive in the sense that we provide a linear-implicit numerical integrator for the multiscale model such that the numerically computable finite element solutions admit weak H1-convergence (at least for a subsequence) towards a weak solution.

magnum.fe: A micromagnetic finite-element simulation code based on FEniCS

We have developed a finite-element micromagnetic simulation code based on the FEniCS package called magnum.fe. Here we describe the numerical methods that are applied as well as their implementation with FEniCS. We apply a transformation method for the solution of the demagnetization-field problem. A semi-implicit weak formulation is used for the integration of the Landau–Lifshitz–Gilbert equation. Numerical experiments show the validity of simulation results. magnum.fe is open source and well documented. The broad feature range of the FEniCS package makes magnum.fe a good choice for the implementation of novel micromagnetic finite-element algorithms.

Landau-Lifshitz-Bloch equation for exchange-coupled grains

Heat assisted recording is a promising technique to further increase the storage density in hard disks. Multilayer recording grains with graded Curie temperature is discussed to further assist the write process. Describing the correct magnetization dynamics of these grains, from room temperature to far above the Curie point, during a write process is required for the calculation of bit error rates. We present a coarse grained approach based on the Landau-Lifshitz-Bloch (LLB) equation to model exchange coupled grains with low computational effort. The required temperature dependent material properties such as the zero-field equilibrium magnetization as well as the parallel and normal susceptibilities are obtained by atomistic Landau-Lifshitz-Gilbert (LLG) simulations. Each grain is described with one magnetization vector. In order to mimic the atomistic exchange interaction between the grains a special treatment of the exchange field in the coarse grained approach is presented.

A three-dimensional spin-diffusion model for micromagnetics.

We solve a time-dependent three-dimensional spin-diffusion model coupled to the Landau-Lifshitz-Gilbert equation numerically. The presented model is validated by comparison to two established spin-torque models: The model of Slonzewski that describes spin-torque in multi-layer structures in the presence of a fixed layer and the model of Zhang and Li that describes current driven domain-wall motion. It is shown that both models are incorporated by the spin-diffusion description, i.e., the nonlocal effects of the Slonzewski model are captured as well as the spin-accumulation due to magnetization gradients as described by the model of Zhang and Li. Moreover, the presented method is able to resolve the time dependency of the spin-accumulation.

A self-consistent spin-diffusion model for micromagnetics.

We propose a three-dimensional micromagnetic model that dynamically solves the Landau-Lifshitz-Gilbert equation coupled to the full spin-diffusion equation. In contrast to previous methods, we solve for the magnetization dynamics and the electric potential in a self-consistent fashion. This treatment allows for an accurate description of magnetization dependent resistance changes. Moreover, the presented algorithm describes both spin accumulation due to smooth magnetization transitions and due to material interfaces as in multilayer structures. The model and its finite-element implementation are validated by current driven motion of a magnetic vortex structure. In a second experiment, the resistivity of a magnetic multilayer structure in dependence of the tilting angle of the magnetization in the different layers is investigated. Both examples show good agreement with reference simulations and experiments respectively.

Areal density optimizations for heat-assisted magnetic recording of high-density media

Heat-assisted magnetic recording (HAMR) is hoped to be the future recording technique for high-density storage devices. Nevertheless, there exist several realization strategies. With a coarse-grained Landau-Lifshitz-Bloch model, we investigate in detail the benefits and disadvantages of a continuous and pulsed laser spot recording of shingled and conventional bit-patterned media. Additionally, we compare single-phase grains and bits having a bilayer structure with graded Curie temperature, consisting of a hard magnetic layer with high TC and a soft magnetic one with low TC, respectively. To describe the whole write process as realistically as possible, a distribution of the grain sizes and Curie temperatures, a displacement jitter of the head, and the bit positions are considered. For all these cases, we calculate bit error rates of various grain patterns, temperatures, and write head positions to optimize the achievable areal storage density. Within our analysis, shingled HAMR with a continuous laser pul...