Francisco Cruz-Gandarilla

Influence of the growth conditions in the properties of the CdTe thin films deposited by CSVT

We present in the results of this work, the influence of oxygen and the gradient of temperature in the processing of CdTe thin films, by using the close space vapor transport (CSVT) technique. In general the kinetic process is strongly influenced by these parameters; where a reduction in the growth rate, grain size; an increase in the intergrain barrier height; and structural changes are present.

Hydrogen Storage in Nanostructured Mg-Base Alloys

Powders of elemental Mg, Zn, Al and Ag were milled in order to produce nanocrystalline alloys with nominal composition Mg98M2 (M=Zn, Al and Ag). Pure Mg was also mechanically milled without any additions. Single-phase nanocrystalline (crystal size 24-26 nm) Mg98M2 alloys were produced after 216 ks of milling. A passivity procedure was followed immediately after milling, by gradually exposing the alloy powders to air (~ 12 hrs). After this procedure, the mechanically alloyed powders were kept under argon atmosphere before being hydrided at 200 and 300 °C under 0.5 and 3 MPa P for 10 min. Previously milled (~ 1.5 years before) and passivated powder alloys (stored in air and referred to as “AE” samples) were also hydrided under the same conditions. No hydriding was observed in the as-received Mg powders (crystal size >> 100 nm), but the as-milled, passivated nanocrystalline alloys were partially hydrided (even the AE samples). The amounts of the MgH2 phase in the hydrided samples were larger in the Ar-stored than in the AE samples under all hydriding conditions. The possible role of MgO and Mg hydroxides, as well as of the alloying elements, on the hydriding behavior of the nanostructured, mechanically alloyed powder alloys is discussed.

EBSD characterization of an IF steel processed by Accumulative Roll Bonding

The objective of this work is to study the texture and microstructure evolution of an IF steel deformed by Accumulative Roll Bonding (ARB) using Electron Backscatter Diffraction. Texture changes occur with increasing number of ARB cycles. For the early cycles, the main components are the α and γ fiber components characteristic of steels. With increasing the number of ARB cycles a tendency towards a random texture is obtained. In the initial state, the mean grain size is 30 μm and after 5 cycles it decreases to 1.2 μm. For the first ARB cycles, the fraction of high angle grain boundary is low but it increases with the number of cycles to about 80% for 5 cycles. The Kernel Average Misorientation (KAM) has no appreciable changes with the number of ARB cycles for all the texture components.

Study of Local Microstructure and Texture Heterogeneities in Hot Rolled CGO Fe-3%Si Sheets

After secondary recrystallization, the Fe-3%Si alloys, grade Conventional Grain Oriented (C.G.O.), exhibit a Goss texture that is sought for minimizing watt losses in transformer cores. The mechanisms of Goss grain formation and their evolution during the processing route from hot rolling to decarburizing such as the early first steps of abnormal growth are not still well cleared up. This work deals with the influence of local microstructure and texture heterogeneities observed by X-ray diffraction (XRD) and Electron Back Scattered Diffraction (EBSD) at the hot rolling step. The present results complete those previously obtained by neutron diffraction [1]. Presence of Goss grain colonies at about the quarter of the hot rolled sheet is probably, as it has already been suggested, at the origin of the Goss grain presence at the primary recrystallized state.

Generalized Pole Figures and Stored Energy Distribution Function Obtained by X-Ray Diffraction

Abstract. Anisotropy of physical and mechanical properties of textured polycrystalline materials strongly depends on microstructural characteristics, such as subgrain sizes, lattice deformations, etc. Generalized Pole Figures (GPF) are an attempt to estimate the anisotropy of these properties; so, the energy stored during plastic deformation is a key parameter in primary recrystallization. In this work, the technique to measure GPF (measurements and software) was implemented for X-Ray diffraction and applied to study of property anisotropy of a Fe50%Ni alloy. GPF’s of texture, crystallite size, stored energy and diffraction peak shift, (among others) have been characterized. The Full Width at Half Maximum (FWHM) of obtained instrumental functions shows that defocusing is significant for polar angle higher than 50°. The mixing parameter of the pseudo-Voigt function using in fitting, presents important dispersions.

Characterization of Global and Local Textures in Hot Rolled CGO Fe3%Si

The present work is an attempt to understand the recrystallisation mechanisms in Fe-3% Si alloys used in transformer cores. After secondary recrystallisation silicon steels exhibit a Goss texture with a more or less important spread depending on the details of the processing route, namely, Conventional Grain Orientation CGO or High Permeability Hi-B. The mechanisms of Goss grain formation during hot rolling and primary recrystallisation, as well as those controlling the first steps of abnormal growth, are not yet well understood. The present work mainly deals with texture characterization of the hot rolled state. Surface, quarter and half thickness samples are prepared from hot-rolled sheet. Global and local textures are characterized by neutron diffraction and electron backscattered diffraction, respectively. The Orientation Distribution Functions and the volume fraction of the different texture components are calculated. The components from global texture measurements are (001)[1-10], (112)[1-10] (α fiber ), (011)[100] (Goss) and (111)[1-21] (111) [1-10](γ fiber). EBSD measurements have shown large variations of texture from the surface to the half thickness of the sheet. These local measurements are related to the global results by rotation about the transverse direction. Moreover, the grain size appears to be inhomogeneous.

The Transformation of Co-Rich Alloys Produced by Mechanical Alloying

Elemental powder mixtures of Co and Ti were subjected to high-energy ball milling in order to produce mechanically alloyed powders with nominal compositions Co64Ti36, Co67Ti33, Co70Ti30, Co73Ti27, Co76Ti24 and Co85Ti15. The mechanically alloyed powders were treated during 30 minutes in inert atmosphere at temperatures in the range 300 – 700 °C. Both the as-milled powders as well as those subjected to heat treatments have been characterized by x-ray diffraction, scanning electron microscopy, energy-dispersive x-ray spectrometry and differential thermal analysis. As-milled products consist mostly of agglomerated powders with a size between 10 and 80 µm which give an amorphous-like diffraction pattern, except for the Co85Ti15 sample whose pattern presents the characteristic peaks of the Co3Ti intermetallic phase. The transformation of the asmilled powders occurs at temperatures in the range of about 530 – 670 °C with clearly observed exothermic events. The Co3Ti phase is found in all heat treated samples, together with fcc-Co (in Co76Ti24 and Co85Ti15) or the hexagonal Co2Ti intermetallic phase (in Co64Ti36, Co67Ti33 and Co70Ti30); the Co73Ti27 sample was essentially single-phase Co3Ti after heating to 700 °C. Our results suggest the occurrence of crystallization of an amorphous phase in two overlapping stages during heating of the mechanically alloyed powders.