Frank P. Nothdurft

Zirconium Dioxide Implant Abutments for Posterior Single-Tooth Replacement: First Results

BACKGROUND Prefabricated implant abutments made of zirconium dioxide (yttria-stabilized polycrystalline tetragonal zirconia; Y-TZP) have proved to be useful in the esthetically demanding anterior region and may also be useful for premolar and molar replacement because of their obvious positive impact on the health of peri-implant soft tissues. METHODS Forty screw implants were inserted in the posterior region of 24 patients and provided with prefabricated all-ceramic abutments made of zirconium dioxide Y-TZP. Zirconia-based crowns were used as superstructures. The following parameters were used to document the state of soft tissue: the modified plaque index (mPI), sulcus fluid flow rate (SFFR), modified sulcus bleeding index (mSBI), and probing depth (PD). Additionally, implant stability was measured using an electronic mobility testing device. RESULTS All implants (N = 40) followed up after 6 months in function were osseointegrated and showed good stability. In the presence of good oral hygiene (mPI: 0.3), the parameters SFFR (16) and mSBI (0.7) were indicative of stable and healthy soft tissue. The mean PD was highest at the distal points of measurement (2.4 mm) and was generally at a low level. Neither implant loss nor crown fractures occurred. Chipping of parts of the veneering ceramic was registered in three cases (7.5%). CONCLUSIONS After 6 months in function, no mechanical failure was registered in any of the all-ceramic abutments. On clinical investigation, the peri-implant soft tissues were largely healthy and devoid of inflammation.

Prefabricated zirconium dioxide implant abutments for single‐tooth replacement in the posterior region: evaluation of peri‐implant tissues and superstructures after 12 months of function

AIM In the present study, prefabricated abutments made of zirconium dioxide Y-TZP (tetragonal zirconia polycrystals) were inserted into the posterior region under controlled clinical conditions. The aim was to test whether abutments made of zirconium dioxide are suitable for this indication. Investigation parameters included reactions of peri-implant tissue and the structural integrity of the all-ceramic superstructures on the implants. Results after 12 months in function are reported in this article. MATERIAL AND METHODS Forty implants of the XiVE S plus screw-type implants (DENTSPLY Friadent) were inserted into the posterior region of 24 patients. After the healing period, the implants were provided with all-ceramic abutments made of zirconium dioxide Y-TZP (FRIADENT CERCON Abutment; DENTSPLY Friadent). All-ceramic crowns (CERCON smart ceramics; DENTSPLY DeguDent) were used as superstructures and cemented using the conventional method. The following parameters were used to document the state of soft tissue: modified plaque index (mPI), sulcus fluid flow rate (SFFR, Periotron; Oraflow Inc), modified sulcus bleeding index (mSBI) and pocket depth (ST). Mesial and distal bone levels were determined on radiographs during the prosthetic treatment and at the 12-month recall. The Periotest (Medizintechnik Gulden) was used to determine implant stability. RESULTS All implants could be followed up after 12 months in function. In the presence of good oral hygiene (mPI: 0.5), the parameters SFFR (18) and mSBI (0.5) were indicative of stable and healthy soft tissue. ST was highest at the distal points of measurement (2.3 mm) and was generally at a low level. Compared with the baseline situation, proximal bone defects were reduced from -1.1 to -1 mm during the 12-month period of functioning. The mean Periost values at the 12-month recall were -1.9 in the maxilla and -3.8 in the mandible. Neither implant loss nor crown fractures occurred. Chipping of parts of the veneering ceramic was registered in four cases (10%). CONCLUSION After 12 months of wear, no mechanical failure was registered in any of the all-ceramic abutments. On clinical investigation, the peri-implant hard and soft tissues were largely healthy and devoid of inflammation.

The fracture behavior of premolar teeth with class II cavities restored by both direct composite restorations and endodontic post systems

PURPOSE The aim of the study was to evaluate the influence of different posts on the fracture load and fracture mode of endodontically treated premolars with class II cavities and direct composite restorations in an ex vivo setting. METHODS Forty-eight single-rooted human premolars were endodontically treated and prepared with standardized MO (mesio-occlusal) cavities. Eight teeth each received either no posts or were restored with titanium screws (BKS), glass fiber posts (DentinPost), or quartz fiber posts (DT Light SL). Sixteen teeth were restored with zirconium dioxide posts (CeraPost). BKS-screws and eight zirconium dioxide posts were cemented conventionally with glass ionomer cement; Panavia F resin cement was used for all others. The specimens were restored with direct composite restorations. Eight sound premolars served as the controls. After thermomechanical fatigue testing, the samples were loaded until fracture occurred at an angle of 45 degrees . All specimens were evaluated for fracture lines. RESULTS The sound teeth showed the significant highest fracture load (792.50+/-210.01 N). The group restored with quartz fiber posts differed not significantly from the control. In the groups with fiber posts and titanium screws significant higher fracture load values occurred as in the group with direct composite restorations without posts. The groups with fiber posts did not show a more favorable fracture mode than the other groups. CLINICAL SIGNIFICANCE The use of an intraradicular post in premolars with class II cavities can significantly increase the resistance towards extra-axial forces.

Fracture resistance of a selection of full-contour all-ceramic crowns: an in vitro study.

This study aimed to evaluate the fracture resistance of monolithic single crowns made from zirconia (ZI), lithium disilicate (LS2), or feldspar ceramic (FC). Five groups of crowns representing a maxillary first molar were made with the appropriate dimensions according to the manufacturers instructions. The ZI and LS2 crowns were luted adhesively or cemented conventionally on a metal abutment tooth analog. The feldspar ceramic crowns were luted adhesively. All specimens underwent axial loading until fracture. The crowns in the ZI groups possessed the highest fracture resistance independent of the mode of fixation.

Differential Behavior of Fibroblasts and Epithelial Cells on Structured Implant Abutment Materials: A Comparison of Materials and Surface Topographies

PURPOSE The aim of this study was to compare the proliferation and attachment behavior of fibroblasts and epithelial cells on differently structured abutment materials. MATERIALS AND METHODS Three different surface topographies were prepared on zirconia and titanium alloy specimens and defined as follows: machined (as delivered without further surface modification), smooth (polished), and rough (sandblasted). Energy-dispersive X-ray spectroscopy, topographical analysis, and water contact angle measurements were used to analyze the surface properties. Fibroblasts (HGF1) and epithelial cells (HNEpC) grown on the specimens were investigated 24 hours and 72 hours after seeding and counted using fluorescence imaging. To investigate adhesion, the abundance and arrangement of the focal adhesion protein vinculin were evaluated by immunocytochemistry. RESULTS Similar surface topographies were created on both materials. Fibroblasts exhibited significant higher proliferation rates on comparable surface topographies of zirconia compared with the titanium alloy. The proliferation of fibroblasts and epithelial cells was optimal on different substrate/topography combinations. Cell spreading was generally higher on polished and machined surfaces than on sandblasted surfaces. Rough surfaces provided favorable properties in terms of cellular adhesion of fibroblasts but not of epithelial cells. CONCLUSIONS Our data support complex soft tissue cell-substrate interactions: the fibroblast and epithelial cell response is influenced by both the material and surface topography.

Pre-fabricated zirconium dioxide implant abutments for single-tooth replacement in the posterior region: success and failure after 3 years of function

Abstract Objective. Zirconia implant abutments have gained a much broader clinical use over the past few years. The aim of the present study was to assess the clinical performance of a pre-fabricated zirconium dioxide implant abutment for single-tooth replacement in the posterior region. Materials and methods. Forty implants of the XiVE® S plus screw type (DENTSPLY Friadent, Mannheim, Germany) were inserted in the posterior region of 24 patients and provided with zirconium dioxide abutments (FRIADENT® CERCON® Abutment, DENTSPLY Friadent). The following parameters were used to document the state of soft tissue: modified plaque index, modified sulcus bleeding index and pocket depth. Mesial and distal bone levels were determined on radiographs during the prosthetic treatment and at the 36-month recall. Results. Thirty-seven implants could be followed up after 36 months in function. One patient wearing two abutments was lost to follow-up. One abutment exhibited a rotational misfit after 2 years in function. A further abutment showed the same failure at the 36-months recall appointment. In the remaining 36 implants the soft and hard tissue parameters were indicative of a low inflammatory status. Compared to the baseline situation, a partly significant bone apposition could be observed. Chipping of parts of the veneering ceramic was registered in 22% of the remaining implant restorations. Conclusions. The use of zirconia abutments in this study lead to mainly healthy peri-implant hard and soft tissue conditions but, considering the observed failures after 3 years in function, clinical long-term results should be awaited before recommending full zirconia implant abutments in a posterior indication.

Fracture behavior of metal-ceramic fixed dental prostheses with frameworks from cast or a newly developed sintered cobalt-chromium alloy

ObjectivesThe aim of this study was to investigate the fracture behavior of metal-ceramic bridges with frameworks from cobalt-chromium-molybdenum (CoCrMo), which are manufactured using conventional casting or a new computer-aided design/computer-aided manufacturing (CAD/CAM) milling and sintering technique.Materials and methodsA total of 32 metal-ceramic fixed dental prostheses (FDPs), which are based on a nonprecious metal framework, was produced using a conventional casting process (n = 16) or a new CAD/CAM milling and sintering process (n = 16). Eight unveneered frameworks were manufactured using each of the techniques. After thermal and mechanical aging of half of the restorations, all samples were subjected to a static loading test in a universal testing machine, in which acoustic emission monitoring was performed. Three different critical forces were revealed: the fracture force (Fmax), the force at the first reduction in force (Fdecr1), and the force at the critical acoustic event (Facoust1).ResultsWith the exception of the veneered restorations with cast or sintered metal frameworks without artificial aging, which presented a statistically significant but slightly different Fmax, no statistically significant differences between cast and CAD/CAM sintered and milled FDPs were detected. Thermal and mechanical loading did not significantly affect the resulting forces.ConclusionsCast and CAD/CAM milled and sintered metal-ceramic bridges were determined to be comparable with respect to the fracture behavior.Clinical significanceFDPs based on CAD/CAM milled and sintered frameworks may be an applicable and less technique-sensitive alternative to frameworks that are based on conventionally cast frameworks.

In vitro investigation of the performance of different restorative materials under cast circumferential clasps for removable dental prostheses

ObjectivesThe objective of this in vitro study was to investigate the behavior of different composite restorative materials under the load of cast circumferential clasps for removable dental prostheses (RDPs).MethodsIn 60 human molars, standardized mesial–occlusal–distal cavities were prepared. The cavities were restored with the following materials: Definite, Tetric Ceram, SureFil, Heliomolar RO, Ariston pHc, and Oralloy, and provided with a rest seat. The rest seats were subjected to 5,000 cycles of thermal cycling and 1,200,000 masticatory cycles in a mastication simulator via cobalt–chromium circumferential clasps cast to standardized frameworks in a laboratory model designed to simulate the biomechanics of a free-end denture base. Fracture analysis of the restorations was performed by light microscopy. Before and after loading, material wear was measured with a 3D-laser scanner, and an analysis of the marginal quality was performed in an SEM at ×200 applying the replica technique.ResultsNo significant differences in the fracture behavior among the composite materials were found; the amalgam control group showed a significantly higher fracture resistance. Regarding the wear of the materials, the composites Definite and SureFil exhibited a behavior similar to that of amalgam. The other composites demonstrated higher wear rates. The initial marginal quality was significantly worse for Ariston pHc. The marginal adaptation decreased significantly after thermal and mechanical loading for Definite and Ariston pHc.ConclusionsIn terms of the investigated aspects of mechanical performance, the tested composites seemed to be inferior to amalgam. Further clinical studies are needed to evaluate the ability of composite restorations to provide support for RDP clasps.Clinical relevanceThe use of composites as direct restoration materials should be avoided in teeth, which serve as abutments for clasp-retained RDPs.

Impact of shortened dental arch on oral health-related quality of life over a period of 10 years – a randomized controlled trial

OBJECTIVES To compare oral health-related quality of life (OHRQoL) in patients with either molar replacement by partial removable dental prostheses (PRDP) or with restored shortened dental arches (SDA) over a period of 10 years. METHODS In this multi-center RCT, a consecutive sample of 215 patients with bilateral molar loss in at least one jaw was initially recruited in 14 prosthodontic departments. Of those patients, 150 could be randomly allocated to the treatment groups (SDA: n = 71; PRDP: n = 79), received the allocated treatment, and were available for follow-up assessments. OHRQoL was assessed using the 49-item version of the Oral Health Impact Profile (OHIP) before treatment (baseline) and at follow-ups after treatment (4-8 weeks and 6, 12, 24, 36, 48, 60, 96, and 120 months). To investigate the course of OHRQoL over time, we longitudinally modelled treatment and time effects using mixed-effects models. RESULTS OHRQoL substantially improved from baseline to first follow-up in both groups indicated by a mean decrease in OHIP scores of 20.0 points (95%-CI: 12.5-27.5). When compared to the SDA group, OHRQoL in the PRDP group was not significantly different (-0.6 OHIP points; 95%-CI: -7.1 to 5.9) during the study period when assuming a constant time effect. OHRQoL remained stable over the 10 years with a statistically insignificant time effect (p = 0.848). CONCLUSIONS For patients requesting prosthodontic treatment for their lost molars, treatments with SDA or PRDP improve clinically relevantly OHRQoL and maintain it over a period of 10 years with no option being superior to the other. CLINICAL SIGNIFICANCE Since there was no significant difference between the two treatment options over the observation period of 10 years, and since results have stayed stable over time, patients can be informed that both treatment concepts are equivalent concerning OHRQoL.