Fred Lisdat

Light-Controlled Bioelectrochemical Sensor Based on CdSe/ZnS Quantum Dots

This study reports on the oxygen sensitivity of quantum dot electrodes modified with CdSe/ZnS nanocrystals. The photocurrent behavior is analyzed for dependence on pH and applied potential by potentiostatic and potentiodynamic measurements. On the basis of the influence of the oxygen content in solution on the photocurrent generation, the enzymatic activity of glucose oxidase is evaluated in solution. In order to construct a photobioelectrochemical sensor which can be read out by illuminating the respective electrode area, two different immobilization methods for the fixation of the biocatalyst have been investigated. Both covalent cross-linking and layer-by-layer deposition of GOD by means of the polyelectrolyte polyallylamine hydrochloride show that a sensor construction is possible. The sensing properties of this type of electrode are drastically influenced by the amount and density of the enzyme on top of the quantum dot layer, which can be advantageously adjusted by the layer-by-layer technique. By depositing four bilayers [GOD/PAH](4) on the CdSe/ZnS electrode, a fast-responding sensor for the concentration range of 0.1-5 mM glucose can be prepared. This study opens the door to multianalyte detection with a nonstructured sensing electrode, localized enzymes, and spatial read-out by light.

Quantum-Dot-Modified Electrode in Combination with NADH-Dependent Dehydrogenase Reactions for Substrate Analysis

A quantum dot-electrode system was developed which allows the sensitive detection of NADH (nicotinamide adenine dinucleotide). The colloidal semiconductive CdSe/ZnS nanocrystals (quantum dots) are attached to gold by chemisorption via a dithiol compound. The current signal can be triggered by illumination of the quantum-dot-modified electrode surface. Because of photoexcitation, electron-hole pairs are generated in the quantum dots, which can be detected as anodic or cathodic photocurrent. The immobilization of the nanocrystals is verified by amperometric photocurrent and quartz crystal microbalance (QCM) measurements. This study shows that CdSe/ZnS quantum dot-modified electrodes allow concentration dependent NADH detection in the range of 20 microM to 2 mM already at rather low potentials (around 0 V vs. Ag/AgCl, 1 M KCl). Therefore such electrodes can be used in combination with NADH-producing enzyme reactions for the light-triggered analysis of the respective substrates of the biocatalyst. It can be shown that glucose detection is feasible with such an electrode system and photocurrent measurements.

Immobilization of Quantum Dots via Conjugated Self-Assembled Monolayers and Their Application as a Light-Controlled Sensor for the Detection of Hydrogen Peroxide

A light-addressable gold electrode modified with CdS and FePt or with CdS@FePt nanoparticles via an interfacial dithiol linker layer is presented. XPS measurements reveal that trans-stilbenedithiol provides high-quality self-assembled monolayers compared to benzenedithiol and biphenyldithiol, in case they are formed at elevated temperatures. The CdS nanoparticles in good electrical contact with the electrode allow for current generation under illumination and appropriate polarization. FePt nanoparticles serve as catalytic sites for the reduction of hydrogen peroxide to water. Advantageously, both properties can be combined by the use of hybrid nanoparticles fixed on the electrode by means of the optimized stilbenedithiol layer. This allows a light-controlled analysis of different hydrogen peroxide concentrations.

Light triggered detection of aminophenyl phosphate with a quantum dot based enzyme electrode

An electrochemical sensor for p-aminophenyl phosphate (p APP) is reported. It is based on the electrochemical conversion of 4-aminophenol (4AP) at a quantum dot (QD) modified electrode under illumination. Without illumination no electron transfer and thus no oxidation of 4AP can occur. p APP as substrate is converted by the enzyme alkaline phosphatase (ALP) to generate 4AP as a product. The QDs are coupled via 1,4-benzenedithiol (BDT) linkage to the surface of a gold electrode and thus allow potential-controlled photocurrent generation. The photocurrent is modified by the enzyme reaction providing access to the substrate detection. In order to develop a photobioelectrochemical sensor the enzyme is immobilized on top of the photo-switchable layer of the QDs. Immobilization of ALP is required for the potential possibility of spatially resolved measurements. Geometries with immobilized ALP are compared versus having the ALP in solution. Data indicate that functional immobilization with layer-by-layer assembly is possible. Enzymatic activity of ALP and thus the photocurrent can be described by Michaelis- Menten kinetics. p APP is detected as proof of principle investigation within the range of 25 μM - 1 mM.

Evaluation of quantum dots applied as switchable layer in a light-controlled electrochemical sensor

AbstractGold electrodes with switchable conductance are created by coating the gold surface with different colloidal quantum dots. For the quantum dot immobilization, a dithiol compound was used. By polarizing the electrode and applying a light pointer, local photocurrents were generated. The performance of this setup was characterized for a variety of different nanoparticle materials regarding drift and signal-to-noise ratio. We varied the following parameters: quantum dot materials and immobilization protocol. The results indicate that the performance of the sensor strongly depends on how the quantum dots are bound to the gold electrode. The best results were obtained by inclusion of an additional polyelectrolyte film, which had been fabricated using layer-by-layer assembly. FigureGold electrode with switchable conductance created by the coating the gold surface with different colloidal quantum dots

Photo-electrochemical Bioanalysis of Guanosine Monophosphate Using Coupled Enzymatic Reactions at a CdS/ZnS Quantum Dot Electrode.

A photo-electrochemical sensor for the specific detection of guanosine monophosphate (GMP) is demonstrated, based on three enzymes combined in a coupled reaction assay. The first reaction involves the adenosine triphosphate (ATP)-dependent conversion of GMP to guanosine diphosphate (GDP) by guanylate kinase, which warrants substrate specificity. The reaction products ADP and GDPare co-substrates for the enzymatic conversion of phosphoenolpyruvate to pyruvate in a second reaction mediated by pyruvate kinase. Pyruvate in turn is the co-substrate for lactate dehydrogenase that generates lactate via oxidation of nicotinamide adenine dinucleotide (reduced form) NADH to NAD(+). This third enzymatic reaction is electrochemically detected. For this purpose a CdS/ZnS quantum dot (QD) electrode is illuminated and the photocurrent response under fixed potential conditions is evaluated. The sequential enzyme reactions are first evaluated in solution. Subsequently, a sensor for GMP is constructed using polyelectrolytes for enzyme immobilization.

Light-addressable amperometric electrodes for enzyme sensors based on direct quantum dot-electrode contacts

Quantum dots allow the generation of charge carriers upon illumination. When these particles are attached to an electrode a photocurrent can be generated. This allows their use as a light-switchable layer on the surface. The QDs can not only exchange electronics with the electrode, but can also interact with donor or acceptor compounds in solution providing access to the construction of signal chains starting from an analytic molecule. The magnitude and the direction of the photocurrent depend on several factors such as electrode polarization, solution pH and composition. These defined dependencies have been evaluated with respect to the combination of QD-electrodes with enzyme reactions for sensorial purpose. CdSe/ZnS-QD-modified electrodes can be used to follow enzymatic reactions in solution based on the oxygen sensitivity. In order to develop a photoelectrochemical biosensor, e.g. glucose oxidase is immobilized on the CdSe/ZnS-electrode. One immobilization strategy applies the layer-by-layer-technique of GOD and a polyelectrolyte. Photocurrent measurements of such a sensor show a clear concentration dependent behavior. The principle of combing QD oxidase. The sensitivity of quantum dot electrodes can be influenced by additional nanoparticles, but also by multiple layers of the QDs. In another direction of research it can be influenced by additional nanoparticles, but also by multiple layers of the QDs. In another direction of research it can be demonstrated that direct electron transfer from excited quantum dots can be achieved with the redox protein cytochrome c. This allows the detection of the protein, but also interaction partners such as a enzymes or superoxide.