G. Binnig

Tunneling through a controllable vacuum gap

We report on the first successful tunneling experiment with an externally and reproducibly adjustable vacuum gap. The observation of vacuum tunneling is established by the exponential dependence of the tunneling resistance on the width of the gap. The experimental setup allows for simultaneous investigation and treatment of the tunnel electrode surfaces.

The Millipede: more than one thousand tips for future AFM data storage

We report on a new atomic force microscope (AFM)-based data storage concept called the “Millipede” that has a potentially ultrahigh density, terabit capacity, small form factor, and high data rate. Its potential for ultrahigh storage density has been demonstrated by a new thermomechanical local-probe technique to store and read back data in very thin polymer films. With this new technique, 30–40-nm-sized bit indentations of similar pitch size have been made by a single cantilever/tip in a thin (50-nm) polymethylmethacrylate (PMMA) layer, resulting in a data storage density of 400–500 Gb/in. 2 High data rates are achieved by parallel operation of large two-dimensional (2D) AFM arrays that have been batch-fabricated by silicon surface-micromachining techniques. The very large scale integration (VLSI) of micro/nanomechanical devices (cantilevers/tips) on a single chip leads to the largest and densest 2D array of 32 × 32 (1024) AFM cantilevers with integrated write/read storage functionality ever built. Time-multiplexed electronics control the write/read storage cycles for parallel operation of the Millipede array chip. Initial areal densities of 100–200 Gb/in. 2 have been achieved with the 32 × 32 array chip, which has potential for further improvements. In addition to data storage in polymers or other media, and not excluding magnetics, we envision areas in nanoscale science and technology such as lithography, high-speed/large-scale imaging, molecular and atomic manipulation, and many others in which Millipede may open up new perspectives and opportunities.

True Atomic Resolution by Atomic Force Microscopy Through Repulsive and Attractive Forces

The (1014) cleavage plane of calcite has been investigated by atomic force microscopy in water at room temperature. True lateral atomic-scale resolution was achieved; the atomic-scale periodicities as well as the expected relative positions of the atoms within each unit cell were obtained. Along monoatomic step lines, atomic-scale kinks, representing point-like defects, were resolved. Attractive forces on the order of 10-11 newton acting between single atomic sites on the sample and the front atoms of the tip were directly measured and provided the highest, most reliable resolution on a flat, well-ordered surface.

Atomic Resolution with Atomic Force Microscope

The atomic force microscope (AFM) is a promising new method for studying the surface structure of both conductors and insulators. In mapping a graphite surface with an insulating stylus, we have achieved a resolution better than 2.5 A.

7 × 7 Reconstruction on Si(111) Resolved in Real Space

The 7× 7 reconstruction on Si(111) was observed in real space by scanning tunneling microscopy. The experiment strongly favors a modified adatom model with 12 adatoms per unit cell and an inhomogeneously relaxed underlying top layer.

Ultrahigh-density atomic force microscopy data storage with erase capability

We report a simple atomic force microscopy-based concept for a hard disk-like data storage technology. Thermomechanical writing by heating a Si cantilever in contact with a spinning polycarbonate disk has already been reported. Here the medium has been replaced with a thin polymer layer on a Si substrate, resulting in significant improvements in storage density. With this new medium, we achieve bit sizes of 10–50 nm, leading to data densities of 500 Gbit/in.2. We also demonstrate a novel high-speed and high-resolution thermal readback method, which uses the same Si cantilevers that are used in the writing process, and the capability to erase and rewrite data features repeatedly.

Millipede: a MEMS-based scanning-probe data-storage system

Ultrahigh storage densities of up to 1 Tbit/in./sup 2/ or more can be achieved by local-probe techniques to write, read back, and erase data in very thin polymer films. The thermomechanical scanning-probe-based data-storage concept called Millipede combines ultrahigh density, small form factor, and high data rate. After illustrating the principles of operation of the Millipede, we introduce system aspects related to the read-back process, multiplexing, and position-error-signal generation for tracking.

Atomic force microscope cantilevers for combined thermomechanical data writing and reading

Heat conduction governs the ultimate writing and reading capabilities of a thermomechanical data storage device. This work investigates transient heat conduction in a resistively heated atomic force microscope cantilever through measurement and simulation of cantilever thermal and electrical behavior. The time required to heat a single cantilever to bit-writing temperature is near 1 μs and the thermal data reading sensitivity ΔR/R is near 1×10−4 per vertical nm. Finite-difference thermal and electrical simulation results compare well with electrical measurements during writing and reading, indicating design tradeoffs in power requirements, data writing speed, and data reading sensitivity. We present a design for a proposed cantilever that is predicted to be faster and more sensitive than the present cantilever.

Smectic Liquid Crystal Monolayers on Graphite Observed by Scanning Tunneling Microscopy

By means of scanning tunneling microscopy, it is observed that molecules of the form n-alkylcyanobiphenyl, where n = 8 to 12, form two-dimensional crystalline domains when adsorbed onto graphite. The layer spacings measured by tunneling microscopy are 20% larger than those measured previously on bulk material by x-ray diffraction. The structure of the adsorbed molecules is quite different from that of the bulk.

Design of atomic force microscope cantilevers for combined thermomechanical writing and thermal reading in array operation

In thermomechanical data writing, a resistively-heated atomic force microscope (AFM) cantilever tip forms indentations in a thin polymer film. The same cantilever operates as a thermal proximity sensor to detect the presence of previously written data bits. This paper uses recent progress in thermal analysis of the writing and reading modes to develop new cantilever designs for increased speed, sensitivity, and reduced power consumption in both writing and reading operation. Measurements of cantilever electrical resistance during heating reveals physical limits of cantilever writing and reading, and verifies a finite-difference thermal and electrical simulation of cantilever operation. This work proposes two new cantilever designs that correspond to fabrication technology benchmarks. Simulations predict that the proposed cantilevers have a higher data rate and are more sensitive than the present cantilever. The various cantilever designs offer single-bit writing times of 0.2 /spl mu/s-25 /spl mu/s for driving voltages of 2-25 V. The thermal reading /spl Delta/R/R sensitivity is as high as 4/spl times/10/sup -4/ per vertical nm in near steady-state operation.