G. Grasa

New CO2 capture process for hydrogen production combining Ca and Cu chemical loops.

This paper presents a new solids looping process for capturing CO2 while generating hydrogen and/or electricity from natural gas. The process is based on the sorption enhanced reforming of CH4, employing CaO as a high temperature CO2 sorbent, combined with a second chemical loop of CuO/Cu. The exothermic reduction of CuO with CH4 is used to obtain the heat necessary for the decomposition of the CaCO3 formed in the reforming step. The main part of the process is completed by the oxidation of Cu to CuO, which is carried out with air diluted with a product gas recycle of this reactor at sufficiently low temperatures and high pressures to avoid the decomposition of a substantial fraction of CaCO3.

Post-combustion calcium looping process with a highly stable sorbent activity by recarbonation

This paper presents a novel sorbent regeneration technique for post-combustion calcium looping CO2 capture systems. The advantage of this technique is that it can drastically reduce the consumption of limestone in the plant without affecting its efficiency and without the need for additional reagents. The method is based on the re-carbonation of carbonated particles circulating from the carbonator using pure CO2 obtained from the gas stream generated in the calciner. The aim is to maintain the CO2 carrying capacity of the sorbent close to optimum values for CaL post-combustion systems (around 0.2). This is achieved by placing a small regeneration reactor between the carbonator and the calciner. This reactor increases slightly the conversion of CaO to carbonate so that it exceeds the so-called maximum CO2 carrying capacity of the sorbent. This increase compensates for the loss of CO2 carrying capacity that the solids undergo in the next calcination–carbonation cycle. Two series of experiments carried out in a thermogravimetric analyzer over 100 cycles of carbonation–recarbonation–calcination show that the inclusion of this recarbonation step is responsible for an increase in the residual CO2 carrying capacity from 0.07 to 0.16. A conceptual design of the resulting capture system shows that a limestone make-up flow designed specifically for a CO2 capture system can approach zero, when the solid sorbents purged from the CaL system are re-used to desulfurize the flue gas in the existing power plant.

The use of two different models to describe the axial mixing of solids in fluidised beds

Two widely used models to describe axial solid mixing in fluidised beds (the dispersion model and the countercurrent backmixing (CCBM) model) are evaluated against identical sets of experimental data. Experimental work has been obtained at different conditions (gas velocity, particle properties and two column diameters) using an image analysis technique. Previously published data by other authors are also compiled to enlarge the experimental database for model development and validation. It is shown that both models are capable to fit the majority of experiments well, in agreement with a well-known relation between the models in some extreme conditions. This relation is further explored by incorporating independent measurements of the tracer rise velocities during the mixing experiments. It is concluded that, although a simple correlation for the solid dispersion coefficients compiled in this work is useful, the CCBM model is a much more reliable idealisation in describing and scaling up axial solid mixing in fluidised beds.

Waste tyre pyrolysis: modelling of a moving bed reactor.

This paper describes the development of a new model for waste tyre pyrolysis in a moving bed reactor. This model comprises three different sub-models: a kinetic sub-model that predicts solid conversion in terms of reaction time and temperature, a heat transfer sub-model that calculates the temperature profile inside the particle and the energy flux from the surroundings to the tyre particles and, finally, a hydrodynamic model that predicts the solid flow pattern inside the reactor. These three sub-models have been integrated in order to develop a comprehensive reactor model. Experimental results were obtained in a continuous moving bed reactor and used to validate model predictions, with good approximation achieved between the experimental and simulated results. In addition, a parametric study of the model was carried out, which showed that tyre particle heating is clearly faster than average particle residence time inside the reactor. Therefore, this fast particle heating together with fast reaction kinetics enables total solid conversion to be achieved in this system in accordance with the predictive model.

Postcombustion Capture of CO2 with CaO in a Circulating Fluidized Bed Carbonator

There is an emerging postcombustion capture technology that uses CaO to capture CO2 from combustion flue gases in a circulating fluidized bed reactor. This paper summarizes recent work conducted at CSIC to understand and develop this technology. The paper includes experimental results at conditions close to those expected in the real system, carried out in continuous mode in a 30kW test facility made up of two interconnected circulating fluidized bed reactors. In one of the reactors, CO2 is captured from the gas phase by the CaO continuously circulating from a calciner. In the second reactor, the CaCO3 formed in the carbonator is regenerated to CaO and CO2 by calcination. Modeling of the system at process level, at reactor level (in particular the CFB carbonator), and at particle level (decay in capture capability of CaO) is also outlined. The work carried out so far confirms that the carbonator reactors can be designed to attain capture efficiencies between 70–90%, operating at fluid dynamic conditions close to those present in circulating fluidized bed combustors.