G. Verstraete

PH-degradable imidazoquinoline-ligated nanogels for lymph node-focused immune activation

Significance The newest generation of small-molecule vaccine adjuvants aims at triggering specific receptors expressed by dendritic cells, the working horses of our immune system. Unfortunately, owing to their small size, upon administration these molecules rapidly enter systemic circulation and cause systemic inflammation. We report on a nanotechnology-based solution for this issue by covalent ligation of a potent immunostimulatory small molecule to hydrogel nanoparticles. This approach allows for lymph node-restricted immune activation and avoids systemic dissemination. Importantly, relative to soluble immunostimulatory compound, nanoparticle ligation yields increased immune activation in the draining lymph nodes and results in strongly increased antibody titers and T-cell responses against an admixed vaccine antigen. Agonists of Toll-like receptors (TLRs) are potent activators of the innate immune system and hold promise as vaccine adjuvant and for anticancer immunotherapy. Unfortunately, in soluble form they readily enter systemic circulation and cause systemic inflammatory toxicity. Here we demonstrate that by covalent ligation of a small-molecule imidazoquinoline-based TLR7/8 agonist to 50-nm-sized degradable polymeric nanogels the potency of the agonist to activate TLR7/8 in in vitro cultured dendritic cells is largely retained. Importantly, imidazoquinoline-ligated nanogels focused the in vivo immune activation on the draining lymph nodes while dramatically reducing systemic inflammation. Mechanistic studies revealed a prevalent passive diffusion of the nanogels to the draining lymph node. Moreover, immunization studies in mice have shown that relative to soluble TLR7/8 agonist, imidazoquinoline-ligated nanogels induce superior antibody and T-cell responses against a tuberculosis antigen. This approach opens possibilities to enhance the therapeutic benefit of small-molecule TLR agonist for a variety of applications.

Hydrophilic thermoplastic polyurethanes for the manufacturing of highly dosed oral sustained release matrices via hot melt extrusion and injection molding

Hydrophilic aliphatic thermoplastic polyurethane (Tecophilic™ grades) matrices for high drug loaded oral sustained release dosage forms were formulated via hot melt extrusion/injection molding (HME/IM). Drugs with different aqueous solubility (diprophylline, theophylline and acetaminophen) were processed and their influence on the release kinetics was investigated. Moreover, the effect of Tecophilic™ grade, HME/IM process temperature, extrusion speed, drug load, injection pressure and post-injection pressure on in vitro release kinetics was evaluated for all model drugs. (1)H NMR spectroscopy indicated that all grades have different soft segment/hard segment ratios, allowing different water uptake capacities and thus different release kinetics. Processing temperature of the different Tecophilic™ grades was successfully predicted by using SEC and rheology. Tecophilic™ grades SP60D60, SP93A100 and TG2000 had a lower processing temperature than other grades and were further evaluated for the production of IM tablets. During HME/IM drug loads up to 70% (w/w) were achieved. In addition, Raman mapping and (M)DSC results confirmed the homogenous distribution of mainly crystalline API in all polymer matrices. Besides, hydrophilic TPU based formulations allowed complete and sustained release kinetics without using release modifiers. As release kinetics were mainly affected by drug load and the length of the PEO soft segment, this polymer platform offers a versatile formulation strategy to adjust the release rate of drugs with different aqueous solubility.

Evaluation of combination therapy for Burkholderia cenocepacia lung infection in different in vitro and in vivo models

Burkholderia cenocepacia is an opportunistic pathogen responsible for life-threatening infections in cystic fibrosis patients. B. cenocepacia is extremely resistant towards antibiotics and therapy is complicated by its ability to form biofilms. We investigated the efficacy of an alternative antimicrobial strategy for B. cenocepacia lung infections using in vitro and in vivo models. A screening of the NIH Clinical Collection 1&2 was performed against B. cenocepacia biofilms formed in 96-well microtiter plates in the presence of tobramycin to identify repurposing candidates with potentiator activity. The efficacy of selected hits was evaluated in a three-dimensional (3D) organotypic human lung epithelial cell culture model. The in vivo effect was evaluated in the invertebrate Galleria mellonella and in a murine B. cenocepacia lung infection model. The screening resulted in 60 hits that potentiated the activity of tobramycin against B. cenocepacia biofilms, including four imidazoles of which econazole and miconazole were selected for further investigation. However, a potentiator effect was not observed in the 3D organotypic human lung epithelial cell culture model. Combination treatment was also not able to increase survival of infected G. mellonella. Also in mice, there was no added value for the combination treatment. Although potentiators of tobramycin with activity against biofilms of B. cenocepacia were identified in a repurposing screen, the in vitro activity could not be confirmed nor in a more sophisticated in vitro model, neither in vivo. This stresses the importance of validating hits resulting from in vitro studies in physiologically relevant model systems.

3D printing of high drug loaded dosage forms using thermoplastic polyurethanes

It was the aim of this study to develop high drug loaded (>30%, w/w), thermoplastic polyurethane (TPU)-based dosage forms via fused deposition modelling (FDM). Model drugs with different particle size and aqueous solubility were pre-processed in combination with diverse TPU grades via hot melt extrusion (HME) into filaments with a diameter of 1.75 ± 0.05 mm. Subsequently, TPU-based filaments which featured acceptable quality attributes (i.e. consistent filament diameter, smooth surface morphology and good mechanical properties) were printed into tablets. The sustained release potential of the 3D printed dosage forms was tested in vitro. Moreover, the impact of printing parameters on the in vitro drug release was investigated. TPU-based filaments could be loaded with 60% (w/w) fine drug powder without observing severe shark skinning or inconsistent filament diameter. During 3D printing experiments, HME filaments based on hard TPU grades were successfully converted into personalized dosage forms containing a high concentration of crystalline drug (up to 60%, w/w). In vitro release kinetics were mainly affected by the matrix composition and tablet infill degree. Therefore, this study clearly demonstrated that TPU-based FDM feedstock material offers a lot of formulation freedom for the development of personalized dosage forms.

A comparative study between melt granulation/compression and hot melt extrusion/injection molding for the manufacturing of oral sustained release thermoplastic polyurethane matrices

During this project 3 techniques (twin screw melt granulation/compression (TSMG), hot melt extrusion (HME) and injection molding (IM)) were evaluated for the manufacturing of thermoplastic polyurethane (TPU)-based oral sustained release matrices, containing a high dose of the highly soluble metformin hydrochloride. Whereas formulations with a drug load between 0 and 70% (w/w) could be processed via HME/(IM), the drug content of granules prepared via melt granulation could only be varied between 85 and 90% (w/w) as these formulations contained the proper concentration of binder (i.e. TPU) to obtain a good size distribution of the granules. While release from HME matrices and IM tablets could be sustained over 24h, release from the TPU-based TSMG tablets was too fast (complete release within about 6h) linked to their higher drug load and porosity. By mixing hydrophilic and hydrophobic TPUs the in vitro release kinetics of both formulations could be adjusted: a higher content of hydrophobic TPU was correlated with a slower release rate. Although mini-matrices showed faster release kinetics than IM tablets, this observation was successfully countered by changing the hydrophobic/hydrophilic TPU ratio. In vivo experiments via oral administration to dogs confirmed the versatile potential of the TPU platform as intermediate-strong and low-intermediate sustained characteristics were obtained for the IM tablets and HME mini-matrices, respectively.

Thermoplastic polyurethane-based intravaginal rings for prophylaxis and treatment of (recurrent) bacterial vaginosis

The aim of the present study was to develop thermoplastic polyurethane (TPU)-based intravaginal rings (IVRs) for prophylaxis and treatment of bacterial vaginosis via hot melt extrusion/injection molding. Therefore, different TPU grades were processed in combination with lactic acid or metronidazole, targeting a sustained lactic acid release over a 28day-period and sustained metronidazole release over 4-7days. Hot melt extrusion of lactic acid/TPU combinations required a lower extrusion temperature due to the plasticizing properties of lactic acid, evidenced by the lower glass transition temperature (Tg) and cross-over point (Ttanδ=1) values. NIR-chemical imaging data showed a homogenous distribution of lactic acid in TPU matrices at drug loads up to 30% (w/w). The addition of metronidazole did not lower processing temperatures, as the active pharmaceutical ingredient remained crystalline in the TPU matrix. Hydrophobic TPUs with a low ratio between the soft and hard segments (SS/HS ratio) in the polymer structure were suitable carriers for the lactic acid-eluting device over a 28-day period, while hydrophilic TPUs were needed to achieve the required release rate of metronidazole-eluting IVRs. IVRs manufactured with a TPU grade having a higher SS/HS ratio and lactic acid/TPU ratio exhibited a more elastic behavior. The addition of 25% (w/w) metronidazole did not affect the mechanical properties of the IVRs. Hydrophilic TPUs were most prone to biofilm formation by Candida albicans and Staphylococcus aureus, but the incorporation of metronidazole in the device prevented biofilm formation. Based on the drug eluting performance and mechanical tests, a mixture of lactic acid and Tecoflex™ EG-93A (20/80, w/w) and a combination of metronidazole and Tecophilic™ SP-93A-100 (25/75, w/w) were selected to design IVRs for the prophylaxis and treatment of bacterial vaginosis, respectively. Slug mucosal irritation tests predicted low irritation potency for both devices.

Downstream processing from hot-melt extrusion towards tablets: A quality by design approach

Since the concept of continuous processing is gaining momentum in pharmaceutical manufacturing, a thorough understanding on how process and formulation parameters can impact the critical quality attributes (CQA) of the end product is more than ever required. This study was designed to screen the influence of process parameters and drug load during HME on both extrudate properties and tableting behaviour of an amorphous solid dispersion formulation using a quality-by-design (QbD) approach. A full factorial experimental design with 19 experiments was used to evaluate the effect of several process variables (barrel temperature: 160-200°C, screw speed: 50-200rpm, throughput: 0.2-0.5kg/h) and drug load (0-20%) as formulation parameter on the hot-melt extrusion (HME) process, extrudate and tablet quality of Soluplus®-Celecoxib amorphous solid dispersions. A prominent impact of the formulation parameter on the CQA of the extrudates (i.e. solid state properties, moisture content, particle size distribution) and tablets (i.e. tabletability, compactibility, fragmentary behaviour, elastic recovery) was discovered. The resistance of the polymer matrix to thermo-mechanical stress during HME was confirmed throughout the experimental design space. In addition, the suitability of Raman spectroscopy as verification method for the active pharmaceutical ingredient (API) concentration in solid dispersions was evaluated. Incorporation of the Raman spectroscopy data in a PLS model enabled API quantification in the extrudate powders with none of the DOE-experiments resulting in extrudates with a CEL content deviating>3% of the label claim. This research paper emphasized that HME is a robust process throughout the experimental design space for obtaining amorphous glassy solutions and for tabletting of such formulations since only minimal impact of the process parameters was detected on the extrudate and tablet properties. However, the quality of extrudates and tablets can be optimized by adjusting specific formulations parameters (e.g. drug load).

The use of partially hydrolysed polyvinyl alcohol for the production of high drug-loaded sustained release pellets via extrusion-spheronisation and coating: In vitro and in vivo evaluation

Partially hydrolysed polyvinyl alcohol (PVA) was evaluated as a pelletisation aid for the production of pellets with a high acetaminophen and metformin hydrochloride concentration (>70%, w/w). Mixtures with varying drug concentration and PVA/microcrystalline cellulose (MCC) ratios were processed via extrusion-spheronisation, either after addition of PVA as a dry powder or as an aqueous solution. Finally, high drug- loaded metformin pellets were coated with a methacrylic acid copolymer (Eudragit™ NM 30D) and evaluated for their sustained release potency in vitro and in vivo. The plasticity index of the wet mass increased by the addition of PVA to the formulation, which resulted in enhanced extrusion-spheronisation properties, even at a high drug load. Although the MCC concentration was successfully lowered by adding PVA, the inclusion of MCC in the formulation was essential to overcome problems related to the tackiness effect of PVA during extrusion. Overall, wet addition of PVA was superior to dry addition, as pellets with a higher mechanical strength and narrower particle size distribution were obtained. Pellets containing 87% (w/w) metformin hydrochloride were successfully layered with 20% (w/w) coating material, yielding sustained release pellets with a final drug load of 70% (w/w). In addition, the sustained release characteristics of the PVA-based pellets with a high drug content were confirmed in vivo as no difference with the Glucophage™ SR reference formulation was observed.

The impact of the injection mold temperature upon polymer crystallization and resulting drug release from immediate and sustained release tablets

It was the aim of this study to elucidate the impact of the injection mold temperature upon the polymer crystallinity, its microstructure and the resulting drug release from immediate and sustained release tablets containing semi-crystalline polymers. The immediate release formulation contained 20% (w/w) ketoprofen (KETO) in poly (ethylene oxide) (PEO) and the sustained release formulation contained 20-40% (w/w) metoprolol tartrate (MPT) in polycaprolactone (PCL). Physical mixtures of drug-polymer were characterized via isothermal crystallization experiments using DSC and rheological measurements to elucidate the impact of the drug solid-state upon the crystallization kinetics. Tablets were prepared using various thermal histories (extrusion barrel temperature and injection mold temperatures). Polymer crystallinity and microstructure in the tablets was characterized via DSC and polarized optical microscopy. The polymer microstructure was altered by the various applied thermal histories. The differences in PEO crystallinity induced by the various mold temperatures did not affect the KETO dissolution from the tablets. On the other hand, MPT (20-40% w/w) dissolution from the PCL matrix when extruded at 80 °C and injection molded at 25 and 35 °C was significantly different due to the changes in the polymer microstructure. More perfect polymer crystals are obtained with higher mold temperatures, decreasing the drug diffusion rate through the PCL matrix. The results presented in this study imply that the injection mold temperature should be carefully controlled for sustained release formulations containing hydrophobic semi-crystalline polymers.

A single dose of intravenous combretastatin A4-phosphate is reasonably well tolerated and significantly reduces tumour vascularization in canine spontaneous cancers

Combretastatin A4-phosphate (CA4P) is an anti-tumour vascular targeting agent which selectively blocks tumour blood flow. Research on CA4P in rodent tumour models is extensive; however, knowledge of its effect on spontaneous cancer is scarce. This study was conducted in canine patients with spontaneous solid tumours. The goal was to assess the toxicity and efficacy of CA4P in various spontaneous tumour types. Eight dogs with spontaneous tumours were enrolled and treated with a single dose of 75 mg m-2 intravenous CA4P. The dogs were screened and monitored before and after injection. Pre- and post-treatment tumour blood flow was analysed in vivo by power Doppler ultrasound (PDUS) and contrast-enhanced ultrasound (CEUS). Vessel destruction and tumour necrosis were evaluated by histopathology. Clinically relevant toxicity was limited to one case of temporary tetraparesis; other adverse events were mild. Significant cardiovascular changes were mostly confined to changes in heart rate and cTnI levels. Macroscopic tumour size reduction was evident in 2 dogs. Based on PDUS and CEUS, CA4P induced a significant decrease in vascular index and tumour blood flow. Post-treatment, histopathology revealed a significant increase of necrotic tumoural tissue and a significant reduction in microvessel density in tumoural tissue. Anti-vascular and necrotizing effects of CA4P were documented in a variety of canine spontaneous cancers with only minimal side effects. This is the first study reporting the administration of CA4P to canine cancer patients with in vivo and ex vivo assessment, and a first step toward implementing CA4P in combination therapies in veterinary oncology patients. The use of CA4P in canine patients was approved and registered by the Belgian Federal Agency for Medicines and Health Products (FAMHP) (approval number 0002588, registration number 6518 ID 2F12).