Gabriele Di Blasio

Assessment of the Effect of Low Cetane Number Fuels on a Light Duty CI Engine: Preliminary Experimental Characterization in PCCI Operating Condition

The goal of this paper is to acquire insight into the influence of cetane number (CN) and fuel oxygen on overall engine performance in the Premixed Charge Compression Ignition (PCCI) combustion mode.

Assessment of Closed-Loop Combustion Control Capability for Biodiesel Blending Detection and Combustion Impact Mitigation for an Euro5 Automotive Diesel Engine

The present paper describes the results of a cooperative research project between GM Powertrain Europe and Istituto Motori - CNR aimed at studying the impact of both fresh and highly oxidized Rapeseed Methyl Ester (RME) at different levels of blending on performance, emissions and fuel consumption of modern automotive diesel engines featuring Closed-Loop Combustion Control (CLCC). In parallel, the capability of this system to detect the level of biodiesel blending through the use of specific detection algorithms was assessed. The tests were performed on the recently released 2.0L Euro5 GM diesel engine for passenger car application equipped with embedded pressure sensors in the glow plugs. Various blends of fresh and aged RME with reference diesel fuel were tested, notably 20% RME by volume (B20), 50% (B50) and pure RME (B100). The tests on the multi-cylinder engine were carried out in a wide range of engine operating points for the complete characterization of the biodiesel performance in the New European Driving Cycle (NEDC). The results highlighted that there is not appreciable difference in terms of performance and emission between fresh and oxidized biodiesel, at all levels of blending. On the other hand, the capability of the CLCC control to detect biodiesel blending with reasonable accuracy and to implement the corrective actions for avoiding emission drift and performance losses was successfully demonstrated.

Low Cetane Number Renewable Oxy-fuels for Premixed Combustion Concept Application: Experimental Investigation on a Light Duty Diesel Engine

This paper illustrates the results of an experimental study on the impact of a low cetane number (CN) oxygenated fuel on the combustion process and emissions of a light-duty (LD) single-cylinder research engine. In an earlier study, it was concluded that cyclic oxygenates consistently outperformed their straight and branched counterparts at equal oxygen content and with respect to lowering soot emissions. A clear correlation was reported linking soot and CN, with lower CN fuels leading to more favorable soot levels. It was concluded that a lower CN fuel, when realized by adding low reactive cyclic oxygenates to commercial diesel fuel, manifests in longer ignition delays and thus more premixing. Ultimately, a higher degree of premixing, in turn, was thought to suppress soot formation rates. Such compounds have the advantage to be stable in blends with fossil diesel fuel, to have a boiling point close to the diesel fuel range, and have the potential to be produced in a renewable way from lignin , which has a similar hexagonal hydrocarbon basis, albeit in polymer form. Lignin is currently a widely available second generation biomass waste stream, found in for example the paper pulp industry and cellulosic ethanol plants. In the present work, blends of diesel and cyclohexanone were tested in a LD single cylinder research diesel engine in order to evaluate its effects on the combustion process and pollutant emissions, employing both conventional (i.e. mixing-controlled) combustion (at medium/high engine loads) and premixed combustion (at medium/low loads). The results suggest that the combination of low CN and fuel oxygen appears to have a favorable impact on both fuel efficiency and overall emissions in premixed-mode. For mixing-controlled combustion, at medium/high engine loads, the negative effects of low CN (e.g. retarded combustion phasing) can be overcome with an appropriate calibration of the injection parameters. The high unburnt hydrocarbon emissions at low load, conversely, require a further development of the combustion system design, as well as the after-treatment device. Finally, to realize a more and more precise control of the in-cylinder air-fuel charge, before and during the combustion, the future PCCI fuels have to be tailored to the specific combustion process characteristics. In this framework, renewable low CN oxygenated fuels might function as an enabler for PCCI combustion engines.

Emission reduction technologies for the future low emission rail diesel engines: EGR vs SCR

The EU emission standards for new rail Diesel engines are becoming even more stringent. EGR and SCR technologies can both be used to reduce NOx emissions; however, the use of EGR is usually accompanied by an increase in PM emissions and may require a DPF. On the other hand, the use of SCR requires on-board storage of urea. Thus, it is necessary to study these trade-offs in order to understand how these technologies can best be used in rail applications to meet new emission standards. The present study assesses the application of these technologies in Diesel railcars on a quantitative basis using one and three dimensional numerical simulation tools. In particular, the study considers a 560 kW railcar engine with the use of either EGR or SCR based solutions for NOx reduction. The NOx and PM emissions performances are evaluated over the C1 homologation cycle. The simulation results indicate that either EGR or SCR based solutions can be used to achieve Stage IIIB NOx limits for the 560 kW engine, with an acceptable trade-off regarding BSFC in the case of EGR solutions. In the case of EGR, though, a DPF is necessary to meet Stage IIIB PM limits. Furthermore, SCR based solutions have the potential to go beyond the Stage IIIB NOx limit by scaling up the size of the SCR device and the on-board urea storage. Copyright

Investigation of the combustion in both metal and optical diesel engines using high-glycerol ethers/diesel blends

In this article, a glycerol ethers mixture obtained from etherification of glycerol with tert-butyl alcohol and isobutylene has been used in blend (10% and 20% v/v) within a commercial diesel fuel to feed a single-cylinder research engine derived from a Euro5 compliant four-cylinder engine. The engine has been run in three significant operating points in the New European Driving Cycle emission homologation area. The results have shown the possibility to burn the diesel–glycerol ethers mixture blends without significant impact on combustion characteristics and efficiencies while, due to the oxygen content of the glycerol ethers mixture, important benefits are obtained in terms of NOx-particulate matter trade-offs at the exhaust. Moreover, tests have been performed on a diesel engine with optical access through the piston bowl. The injection and combustion processes of the pilot have been investigated by means of the simultaneous use of digital imaging in the visible and infrared ranges in order to have more information on the vapour distribution, the fuel motion before the ignition and the location of hot gas.

DoE Method for Operating Parameter Optimization of a Dual-Fuel BioEthanol/Diesel Light Duty Engine

In recent years, alcoholic fuels have been considered as an alternative transportation biofuel even in compression ignition engines either as blended in diesel or as premixed fuel in the case of dual-fuel configuration. Within this framework, the authors investigated the possibility to improve the combustion efficiency when ethanol is used in a dual-fuel light duty diesel engine. In particular, the study was focused on reducing the HC and CO emissions at low load conditions, acting on the most influential engine calibration parameters. Since this kind of investigation would require a significant number of runs, the statistical design of experiment methodology was adopted to reduce significantly its number. As required by the DoE approach, a set of factors (injection parameters, etc.) were selected. For each of them, two levels “high” and “low” were defined in a range of reasonable values. Combining the levels of all the factors, it was possible to evaluate the effects and the weight of each factor and of their combination on the outputs. The results identified the rail pressure, the pilot, and post-injection as the most influential emission parameters. Significant reductions of unburnt were found acting on those parameters without substantial penalties on the global engine performances.

Erratum to: Impact of Emerging Engine and After-Treatment Technologies for Improved Fuel Efficiency and Emission Reduction for the Future Rail Diesel Engines

The future stringent emission limits and fuel-saving requirements for non-road engines, in particular for the rail sector, require further research investments both on engine and after-treatment technologies. Therefore, the aim of this study is to identify, mainly on a literature data base, the most promising emerging engine technologies (waste heat recovery, turbocharging, etc.) and exhaust after-treatment systems (de-NOx catalyst systems, particulate filters, etc.) for improved fuel efficiency and emissions reduction of rail diesel engines. The considered technologies are currently from production series or under development mostly in the on-road research domain. The approach taken has been to gather available information and data from research and industry sources for the most promising emerging technologies of on-road heavy-duty (HD) engines. The collected data have been properly analyzed and elaborated in order to identify the most transferable data from road to the rail sector. The study is one of the results of a project carried out within the 7th European Framework program in which several academic and industrial partners have participated. Engine side and exhaust after-treatment system side technologies are discussed separately. The former takes into account quantitative data from the literature survey, mainly in terms of fuel efficiency benefits, and summarizes the evaluation in a return on investment calculation on the base of a reference rail engine cost. In the latter, essentially qualitative information has been collected. The analysis has been carried out by means of spider diagrams that are used to show the potential of the grouped after-treatment technologies in terms of pollutant emission reduction, size/weight reduction, technology maturity, and cost reduction. The results indicate that the emerging engine technologies are mostly about engine efficiency improvements, of which waste heat recovery shows the greatest potential in terms of fuel efficiency improvement. On the after-treatment system side, the integration of multiple after-treatment functionalities into a single device is particularly attractive for rail applications because it could significantly decrease space and weight requirements, as could the use of alternative to urea media for ammonia storage in the case of selective catalytic reduction (SCR) system functionalities.

Diesel exhaust particles induce autophagy and citrullination in Normal Human Bronchial Epithelial cells

A variety of environmental agents has been found to influence the development of autoimmune diseases; in particular, the studies investigating the potential association of systemic autoimmune rheumatic diseases with environmental micro and nano-particulate matter are very few and contradictory. In this study, the role of diesel exhaust particles (DEPs), one of the most important components of environment particulate matter, emitted from Euro 4 and Euro 5 engines in altering the Normal Human Bronchial Epithelial (NHBE) cell biological activity was evaluated. NHBE cells were exposed in vitro to Euro 4 and Euro 5 particle carbon core, sampled upstream of the typical emission after-treatment systems (diesel oxidation catalyst and diesel particulate filter), whose surfaces have been washed from well-assessed harmful species, as polycyclic aromatic hydrocarbons (PAHs) to: (1) investigate their specific capacity to affect cell viability (flow cytometry); (2) stimulate the production of the pro-inflammatory cytokine IL-18 (Enzyme-Linked ImmunoSorbent Assay -ELISA-); (3) verify their specific ability to induce autophagy and elicit protein citrullination and peptidyl arginine deiminase (PAD) activity (confocal laser scanning microscopy, immunoprecipitation, Sodium Dodecyl Sulphate-PolyAcrylamide Gel Electrophoresis -SDS-PAGE- and Western blot, ELISA). In this study we demonstrated, for the first time, that both Euro 4 and Euro 5 carbon particles, deprived of PAHs possibly adsorbed on the soot surface, were able to: (1) significantly affect cell viability, inducing autophagy, apoptosis and necrosis; (2) stimulate the release of the pro-inflammatory cytokine IL-18; (3) elicit protein citrullination and PAD activity in NHBE cells. In particular, Euro 5 DEPs seem to have a more marked effect with respect to Euro 4 DEPs.

Parametric Analysis of the Effect of Pilot Quantity, Combustion Phasing and EGR on Efficiencies of a Gasoline PPC Light-Duty Engine

In this paper, a parametric analysis on the main engine calibration parameters applied on gasoline Partially Premixed Combustion (PPC) is performed. Theoretically, the PPC concept permits to improve both the engine efficiencies and the NOx-soot trade-off simultaneously compared to the conventional diesel combustion. This work is based on the design of experiments (DoE), statistical approach, and investigates on the engine calibration parameters that might affect the efficiencies and the emissions of a gasoline PPC. The full factorial DoE analysis based on three levels and three factors (33 factorial design) is performed at three engine operating conditions of the Worldwide harmonized Light vehicles Test Cycles (WLTC). The pilot quantity (Qpil), the crank angle position when 50% of the total heat is released (CA50), and the exhaust gas recirculation (EGR) factors are considered. The goal is to identify an engine calibration with high efficiency and low emissions. The experiments are conducted on a 2l Volvo Euro 6 diesel engine. The fuels tested are Gasoline RON75 and MK1 diesel. Gasoline RON75 permits operation from low to high engine load conditions. A pilot/main injection strategy is adopted, necessary to control the peak pressure rise rate (PRRmax) to acceptable values and to extend the maximum engine load operating area in PPC. The experimental results show that increasing the EGR rate from 0 to 30%, the net efficiency improves approximately of 1.5% units, due to the shorter combustion duration. For all the conditions examined in PPC, the soot levels are about two times lower than diesel combustion. With a high level of EGR, combined with optimized pilot quantity and combustion phasing, high-efficiency PPC combustion can be achieved without penalties in terms of NOx emissions compared to diesel combustion. (Less)