Gediminas Seniutinas

Black silicon: substrate for laser 3D micro/nano-polymerization

We demonstrate that black silicon (b-Si) made by dry plasma etching is a promising substrate for laser three-dimensional (3D) micro/nano-polymerization. High aspect ratio Si-needles, working as sacrificial support structures, have flexibility required to relax interface stresses between substrate and the polymerized micro-/nano- objects. Surface of b-Si can be made electrically conductive by metal deposition and, at the same time, can preserve low optical reflectivity beneficial for polymerization by direct laser writing. 3D laser polymerization usually performed at the irradiation conditions close to the dielectric breakdown is possible on non-reflective and not metallic surfaces. Here we show that low reflectivity and high metallic conductivity are not counter- exclusive properties for laser polymerization. Electrical conductivity of substrate and its permeability in liquids are promising for bio- and electroplating applications.

Antibacterial titanium nano-patterned arrays inspired by dragonfly wings

Titanium and its alloys remain the most popular choice as a medical implant material because of its desirable properties. The successful osseointegration of titanium implants is, however, adversely affected by the presence of bacterial biofilms that can form on the surface, and hence methods for preventing the formation of surface biofilms have been the subject of intensive research over the past few years. In this study, we report the response of bacteria and primary human fibroblasts to the antibacterial nanoarrays fabricated on titanium surfaces using a simple hydrothermal etching process. These fabricated titanium surfaces were shown to possess selective bactericidal activity, eliminating almost 50% of Pseudomonas aeruginosa cells and about 20% of the Staphylococcus aureus cells coming into contact with the surface. These nano-patterned surfaces were also shown to enhance the aligned attachment behavior and proliferation of primary human fibroblasts over 10 days of growth. These antibacterial surfaces, which are capable of exhibiting differential responses to bacterial and eukaryotic cells, represent surfaces that have excellent prospects for biomedical applications.

Versatile SERS sensing based on black silicon

Black Si (b-Si) with gold or silver metal coating has been shown to be an extremely effective substrate for surface-enhanced Raman scattering (SERS). Here, we demonstrate that it is also a highly versatile SERS platform, as it supports a wide range of surface functionalizations. In particular, we report the use of a molecularly imprinted polymer (MIP) coating and a hydrophobic coating on b-Si to establish two different sensing modalities. First, using a MIP layer on Au-coated b-Si, we show selective sensing of two closely related varieties of tetracycline. Second, a hydrophobic coating was used to concentrate the analyte adsorbed on gold colloidal nanoparticles, thus increasing the sensitivity of the measurement by an order of magnitude. In this experiment, Au nanoparticles and analyte were mixed just before SERS measurements and were concentrated by drop-drying on the super-hydrophobic b-Si. These approaches are promising for SERS measurements that are sensitive to the aging of bare plasmonic metal-coated substrates.

Au-Ag-Cu nano-alloys: tailoring of permittivity

Precious metal alloys enables new possibilities to tailor materials for specific optical functions. Here we present a systematic study of the effects of a nanoscale alloying on the permittivity of Au-Ag-Cu metals at 38 different atomic mixing ratios. The permittivity was measured and analyzed numerically by applying the Drude model. X-ray diffraction (XRD) revealed the face centered cubic lattice of the alloys. Both, optical spectra and XRD results point towards an equivalent composition-dependent electron scattering behavior. Correlation between the fundamental structural parameters of alloys and the resulting optical properties is elucidated. Plasmonic properties of the Au-Ag-Cu alloy nanoparticles were investigated by numerical simulations. Guidelines for designing plasmonic response of nano- structures and their patterns are presented from the material science perspective.

3D nano-structures for laser nano-manipulation

Summary The resputtering of gold films from nano-holes defined in a sacrificial PMMA mask, which was made by electron beam lithography, was carried out with a dry plasma etching tool in order to form well-like structures with a high aspect ratio (height/width ≈ 3–4) at the rims of the nano-holes. The extraordinary transmission through the patterns of such nano-wells was investigated experimentally and numerically. By doing numerical simulations of 50-nm and 100-nm diameter polystyrene beads in water and air, we show the potential of such patterns for self-induced back-action (SIBA) trapping. The best trapping conditions were found to be a trapping force of 2 pN/W/μm2 (numerical result) exerted on a 50-nm diameter bead in water. The simulations were based on the analytical Lorentz force model.

Silk fibroin as a water-soluble bio-resist and its thermal properties

Thermal diffusivity of silk fibroin films, α = (1.6 ± 0.24) × 10−7 m2 s−1, was measured by a direct contact method. It was shown to be reduced down to ∼1 × 10−7 m2 s−1 in the crystallized phase, consistent with the multi-domain composition of β-sheet assemblies. Crystalline silk with β-sheets was made by dipping into alcohol and was used as a positive electron beam lithography (EBL) resist. It is shown by direct IR imaging of the 1619 cm−1 amide-I CO spectral signature and 3290 cm−1 amide-A N–H stretching band that an e-beam is responsible for unzipping β-sheets, which subsequently results in exposed areas returning to a water soluble state. This makes it possible to develop a water-based biocompatible silk resist and use it in lithography applications. The general principles of protein crystallization, traceable to spectral changes in IR amide bands of silk, can be used as a guide for the creation of new protein EBL resists and to quantify the electron dose required for solubility. Foam formation and laser treatments of silk can provide new approaches in surface functionalization and fabrication of 3D bio-scaffolds.

Anti-reflective surfaces: Cascading nano/microstructuring

The creation of anti-reflective surfaces is reliant on the engineering of the surface textures and patterns to enable efficient trapping or transmission of light. Here we demonstrate anti-reflective layers composed of hierarchical nano/microscale features that are prepared on Si using a combination of wet and dry etching processes, and which are both scalable and affordable. The performance of the structured surfaces was tested through optical measurements of the reflectance, transmittance, and scattering spectra from the visible to mid-infrared wavelength regions, and the results were verified using numerical simulations to identify the performance of the textured anti-reflective layers. The anti-reflective properties of the layers were shown to be dramatically improved by the composite nanostructured surfaces over a broad spectral range, which thus provides a basis for the design rules that are essential for the progress towards effective anti-reflector fabrication. At normal incidence, the hierarchical...

Nanostructured Antireflective and Thermoisolative Cicada Wings

Inter-related mechanical, thermal, and optical macroscopic properties of biomaterials are defined at the nanoscale by their constituent structures and patterns, which underpin complex functions of an entire bio-object. Here, the temperature diffusivity of a cicada (Cyclochila australasiae) wing with nanotextured surfaces was measured using two complementary techniques: a direct contact method and IR imaging. The 4-6-μm-thick wing section was shown to have a thermal diffusivity of α⊥ = (0.71 ± 0.15) × 10(-7) m(2)/s, as measured by the contact temperature wave method along the thickness of the wing; it corresponds to the inherent thermal property of the cuticle. The in-plane thermal diffusivity value of the wing was determined by IR imaging and was considerably larger at α∥ = (3.6 ± 0.2) × 10(-7) m(2)/s as a result of heat transport via air. Optical properties of wings covered with nanospikes were numerically simulated using an accurate 3D model of the wing pattern and showed that light is concentrated between spikes where intensity is enhanced by up to 3- to 4-fold. The closely packed pattern of nanospikes reduces the reflectivity of the wing throughout the visible light spectrum and over a wide range of incident angles, hence acting as an antireflection coating.

Tipping solutions: emerging 3D nano-fabrication/ -imaging technologies

Abstract The evolution of optical microscopy from an imaging technique into a tool for materials modification and fabrication is now being repeated with other characterization techniques, including scanning electron microscopy (SEM), focused ion beam (FIB) milling/imaging, and atomic force microscopy (AFM). Fabrication and in situ imaging of materials undergoing a three-dimensional (3D) nano-structuring within a 1−100 nm resolution window is required for future manufacturing of devices. This level of precision is critically in enabling the cross-over between different device platforms (e.g. from electronics to micro-/nano-fluidics and/or photonics) within future devices that will be interfacing with biological and molecular systems in a 3D fashion. Prospective trends in electron, ion, and nano-tip based fabrication techniques are presented.

Photoluminescence from voids created by femtosecond-laser pulses inside cubic-BN.

Photoluminescence (PL) from femtosecond-laser-modified regions inside cubic-boron nitride (c-BN) was measured under UV and visible light excitation. Bright PL at the red spectral range was observed, with a typical excited state lifetime of ∼4  ns. Sharp emission lines are consistent with PL of intrinsic vibronic defects linked to the nitrogen vacancy formation (via Frenkel pair) observed earlier in high-energy electron-irradiated and ion-implanted c-BN. These, formerly known as the radiation centers, RC1, RC2, and RC3, have been identified at the locus of the voids formed by a single femtosecond-laser pulse. The method is promising to engineer color centers in c-BN for photonic applications.