Geert Morthier

Athermal Silicon-on-insulator ring resonators by overlaying a polymer cladding on narrowed waveguides

Athermal silicon ring resonators are experimentally demonstrated by overlaying a polymer cladding on narrowed silicon wires. The ideal width to achieve athermal condition for the TE mode of 220 nm-height SOI waveguides is found to be around 350 nm. After overlaying a polymer layer, the wavelength temperature dependence of the silicon ring resonator is reduced to less than 5 pm/degrees C, almost eleven times less than that of normal silicon waveguides. The optical loss of a 350-nm bent waveguide (with a radius of 15 microm) is extracted from the ring transmission spectrum. The scattering loss is reduced to an acceptable level of about 50 dB/cm after overlaying a polymer cladding.

Gain-coupled DFB lasers versus index-coupled and phase shifted DFB lasers: a comparison based on spatial hole burning corrected yield

A statistical yield analysis is presented for gain- and index-coupled distributed feedback (DFB) laser structures, allowing a comparison of their single longitudinal mode (SLM) yield capabilities. For the yield calculations, the threshold gain difference and the longitudinal spatial hole burning (SHB) are taken into account. By comparing the experimental and theoretical yield of index-coupled DFB lasers, the significance of SHB for correct yield predictions is illustrated. For the purpose of comparison, yield calculations for various lambda /4-shifted DFB lasers (with low facet reflectivities) are presented. The most emphasis, however, is on partly gain-coupled DFB lasers. Estimations of practical gain coupling coefficient values for gain and for loss gratings are discussed. >

CLADISS-a longitudinal multimode model for the analysis of the static, dynamic, and stochastic behavior of diode lasers with distributed feedback

A computer model called CLADISS is presented for the analysis of multisection diode lasers. The model allows for the analysis of a wide variety of multisection devices with discrete or distributed internal reflections. The simulator can carry out a threshold, DC, AC, and a noise analysis. The threshold analysis determines the threshold of the various longitudinal modes of the laser. The power versus current and the wavelength versus current characteristics are found with the self-consistent DC analysis. CLADISS includes all of the longitudinal variations by dividing each laser section in many short segments. Both the optical field and carrier density are discretized according to this segmentation. To demonstrate the capabilities of CLADISS some nonlinear effects in DFB lasers are treated. Instabilities induced in the side-mode suppression ratio by spatial hole burning are considered. The effects of spatial hole burning and side modes on the FM response on the linewidth are discussed. >

Experimental demonstration of reservoir computing on a silicon photonics chip

In todays age, companies employ machine learning to extract information from large quantities of data. One of those techniques, reservoir computing (RC), is a decade old and has achieved state-of-the-art performance for processing sequential data. Dedicated hardware realizations of RC could enable speed gains and power savings. Here we propose the first integrated passive silicon photonics reservoir. We demonstrate experimentally and through simulations that, thanks to the RC paradigm, this generic chip can be used to perform arbitrary Boolean logic operations with memory as well as 5-bit header recognition up to 12.5 Gbit s(-1), without power consumption in the reservoir. It can also perform isolated spoken digit recognition. Our realization exploits optical phase for computing. It is scalable to larger networks and much higher bitrates, up to speeds >100 Gbit s(-1). These results pave the way for the application of integrated photonic RC for a wide range of applications.

Nonlinear properties of and nonlinear processing in hydrogenated amorphous silicon waveguides

We propose hydrogenated amorphous silicon nanowires as a platform for nonlinear optics in the telecommunication wavelength range. Extraction of the nonlinear parameter of these photonic nanowires reveals a figure of merit larger than 2. It is observed that the nonlinear optical properties of these waveguides degrade with time, but that this degradation can be reversed by annealing the samples. A four wave mixing conversion efficiency of + 12 dB is demonstrated in a 320 Gbit/s serial optical waveform data sampling experiment in a 4 mm long photonic nanowire.

Optical bistability and pulsating behaviour in Silicon-On-Insulator ring resonator structures

We demonstrate optical bistability in a Silicon-On-Insulator two-bus ring resonator with input powers as low as 0.3mW. We evaluate the importance of the different nonlinear contributions and derive time constants for carrier and thermal relaxation effects. In some cases, we also observe pulsation due to interaction between the dominant nonlinear effects. Such a behaviour may be problematic for possible memory and switching operations. Alternatively, it could be used for (tunable) pulse generation.

Nanophotonic Devices for Optical Interconnect

We review recent progress in nanophotonic devices for compact optical interconnect networks. We focus on microdisk-laser-based transmitters and discuss improved design and advanced functionality including all-optical wavelength conversion and flip-flops. Next we discuss the fabrication uniformity of the passive routing circuits and their thermal tuning. Finally, we discuss the performance of a wavelength selective detector.

Optical packet routing in IP-over-WDM networks deploying two-level optical labeling

Assigning a wavelength label as well as a label in a DPSK modulation format orthogonal to the data payload significantly increases the forwarding and routing capabilities of optical packet routers in IP-over-WDM networks.

Control of widely tunable SSG-DBR lasers for dense wavelength division multiplexing

This paper presents a general discussion on the control of widely tunable super structure grating distributed Bragg reflector (SSG-DBR) lasers. A feedback control scheme is presented that ensures frequency stability and accuracy (better than /spl plusmn/0.5 GHz), as well as high side mode suppression ratio (>35 dB). The active section voltage is monitored to maintain mode stability and a highly stable Fabry-Perot etalon is used as a reference to lock the laser frequency to a specific ITU channel. It is shown that stability can even be maintained when directly modulating the laser at 1.244 Gb/s. Furthermore, a characterization scheme is demonstrated that uses the voltage monitoring to generate a look-up table of operation points very efficiently and accurately. For all operation points, the frequency accuracy is better than /spl plusmn/0.5 GHz and the side mode suppression ratio is above 35 dB.

Improved performance of AR-coated DFB lasers for the introduction of gain coupling

Antireflection (AR)-coated distributed-feedback (DFB) lasers with both gain- and index-coupled distributed feedback are studied numerically with respect to mode losses, mode suppression, and spatial hole burning. The mode losses and the spatial hole burning decrease with increasing gain coupling, while the mode suppression increases. It is shown that a large improvement in performance can already be obtained for small fractions of gain coupling.<<ETX>>