Giancarlo Galli

Amphiphilic block copolymer/poly(dimethylsiloxane) (PDMS) blends and nanocomposites for improved fouling-release.

Amphiphilic diblock copolymers, Sz6 and Sz12, consisting of a poly(dimethylsiloxane) block (average degree of polymerisation = 132) and a PEGylated-fluoroalkyl modified polystyrene block (Sz, average degree of polymerisation = 6, 12) were prepared by atom transfer radical polymerization (ATRP). Coatings were obtained from blends of either block copolymer (1–10 wt%) with a poly(dimethylsiloxane) (PDMS) matrix. The coating surface presented a simultaneous hydrophobic and lipophobic character, owing to the strong surface segregation of the lowest surface energy fluoroalkyl chains of the block copolymer. Surface chemical composition and wettability of the films were affected by exposure to water. Block copolymer Sz6 was also blended with PDMS and a 0.1 wt% amount of multiwall carbon nanotubes (CNT). The excellent fouling-release (FR) properties of these new coatings against the macroalga Ulva linza essentially resulted from the inclusion of the amphiphilic block copolymer, while the addition of CNT did not appear to improve the FR properties.

Fluorinated/siloxane copolymer blends for fouling release: chemical characterisation and biological evaluation with algae and barnacles.

Fouling-release coatings were prepared from blends of a fluorinated/siloxane copolymer with a poly(dimethyl siloxane) (PDMS) matrix in order to couple the low modulus character of PDMS with the low surface tension typical for fluorinated polymers. The content of the surface-active copolymer was varied in the blend over a broad range (0.15–10 wt % with respect to PDMS). X-ray photoelectron spectroscopy depth profiling analyses were performed on the coatings to establish the distribution of specific chemical constituents throughout the coatings, and proved enrichment in fluorine of the outermost layers of the coating surface. Addition of the fluorinated/siloxane copolymer to the PDMS matrix resulted in a concentration-dependent decrease in settlement of barnacle, Balanus amphitrite, cyprids. The release of young plants of Ulva, a soft fouling species, and young barnacles showed that adhesion strength on the fluorinated/siloxane copolymer was significantly lower than the siloxane control. However, differences in adhesion strength were not directly correlated with the concentration of copolymer in the blends.

Transport Properties of Modified Montmorillonite-Poly(ε-caprolactone) Nanocomposites

A series of montmorillonite-poly(e-caprolactone) nanocomposites were prepared according to a two stage procedure. In the first step Na-type silicate clay was cation exchanged with protonated 12-aminolauric acid. In the second step e-caprolactone was intercalated in the modified clay and ring-opening polymerized. The clay content was varied regulatory from 0 to 44 wt.-%, with exfoliation of the silicate layers being detected by X-ray diffraction in the nanocomposites dispersing up to at least 16 wt.-% clay. Crystallization of poly(e-caprolactone) was not prevented in the nanocomposites, although if proceeded to a lower extent/order than in a homopolymer sample. The transport properties were investigated using water or dichloromethane as vapor permeants. In each case, a dual sorption behavior was observed as a function of the vapor activity because of the occurrence of different sorption mechanisms. The permeability of the nanocomposites to either permeant decreased with increasing clay content. In particular, the permeability behavior to water was largely dominated by the diffusion parameter.

Poly(dimethyl siloxane) (PDMS) network blends of amphiphilic acrylic copolymers with poly(ethylene glycol)-fluoroalkyl side chains for fouling-release coatings. II. Laboratory assays and field immersion trials.

Amphiphilic copolymers containing different amounts of poly(ethylene glycol)-fluoroalkyl acrylate and polysiloxane methacrylate units were blended with a poly(dimethyl siloxane) (PDMS) matrix in different proportions to investigate the effect of both copolymer composition and loading on the biological performance of the coatings. Laboratory bioassays revealed optimal compositions for the release of sporelings of Ulva linza, and the settlement of cypris larvae of Balanus amphitrite. The best-performing coatings were subjected to field immersion tests. Experimental coatings containing copolymer showed significantly reduced levels of hard fouling compared to the control coatings (PDMS without copolymer), their performance being equivalent to a coating based on Intersleek 700™. XPS analysis showed that only small amounts of fluorine at the coating surface were sufficient for good antifouling/fouling-release properties. AFM analyses of coatings under immersion showed that the presence of a regular surface structure with nanosized domains correlated with biological performance.

Engineering low surface energy polymers through molecular design: synthetic routes to fluorinated polystyrene-based block copolymers

New narrow polydisperse polystyrene-based block copolymers comprising fluorinated aromatic substituents in the side chains were synthesized following two different synthetic routes: (i) TEMPO-mediated controlled radical polymerization of fluorinated styrene monomers; (ii) A sequence of polymer modification reactions on anionically formed polystyrene-block-polyisoprene block copolymers. Using the former route, AB diblock and ABA triblock copolymers were obtained in which a block of polystyrene bearing a fluorocarbon chain substituent with a range of nCF2 groups (n = 4, 6, or 8) was incorporated as B block. Following the latter route, polystyrene-block-polyisoprene AB diblock copolymers were prepared by anionic polymerization and then modification by introduction of fluorinated tails with different numbers of CF2 groups (n = 6 or 8). The thermal behavior as well as the bulk microstructure of the fluorinated block copolymers were investigated and the effect of the chemical structure on the properties was evaluated. All the samples showed a tendency to form layered mesophases in the bulk, and increasing the length of the fluorocarbon tail of the side chain enhanced the degree of order of the mesophase from a disordered smectic (n = 4 or 6) to ordered pseudohexagonal smectic (n = 8). Contact angles of block copolymer films were measured using water as the wetting medium. Values of advanced contact angles up to 130° (120° receded angles) were found which were quite constant over prolonged immersion times in water.

The surface-segregated nanostructure of fluorinated copolymer-poly(dimethylsiloxane) blend films.

Two fluorinated/siloxane copolymers, O5/19 and D5/3, carrying 6 and 8 CF(2) groups in the fluoroalkyl tail, respectively, were used as the surface-active components of cured poly(dimethylsiloxane) (PDMS) blends at different loadings (0.3-5.0 wt % with respect to PDMS). The surface chemical composition was determined by angle-resolved X-ray photoelectron spectroscopy at the takeoff angles theta of 0 degrees, 60 degrees, and 75 degrees. It was found that the fluorinated copolymer was surface-segregated, and in-depth segregation (approximately 5 nm) depended upon the chemical structure of the copolymer. The surface fluorine atomic percentage of the blends with D5/3 was up to 3 orders of magnitude higher than the theoretical value expected for ideal homogeneous samples. Moreover, small amounts of the copolymer in the blends were sufficient to saturate the outermost surface in fluorine content. The chemical composition of the surface-segregated nanostructure of the films was also proven to be affected by external environment, namely, exposure to water.

Vehicle effects in ophthalmic bioavailability: an evaluation of polymeric inserts containing pilocarpine

A series of polymeric ophthalmic inserts containing pilocarpine were formulated with four different types of polyvinyl alcohol, PVA, and two types of hydroxypropylcellulose. Pilocarpine was present as the nitrate, or as the salt with polyacrylic acid, PAA. In‐vivo miosis vs time experiments on albino rabbits, showed that all inserts increased significantly the bioavailability of pilocarpine, with respect to a standard solution of pilocarpine nitrate. Two PVA inserts, containing the PAA‐salt of pilocarpine, were particularly effective. The preparations were also submitted to in‐vitro release tests and to differential scanning calorimetry, to ascertain the release mechanism, and to verify, via the thermal behaviour, possible interactions between drug and polymers. The chemical and physicochemical factors, most likely to influence the ophthalmic bioavailability of pilocarpine from the present preparations, are briefly reviewed.

A comparison between different fouling-release elastomer coatings containing surface-active polymers

Surface-active polymers derived from styrene monomers containing siloxane (S), fluoroalkyl (F) and/or ethoxylated (E) side chains were blended with an elastomer matrix, either poly(dimethyl siloxane) (PDMS) or poly(styrene-b-(ethylene-co-butylene)-b-styrene) (SEBS), and spray-coated on top of PDMS or SEBS preformed films. By contact angle and X-ray photoelectron spectroscopy measurements, it was found that the surface-active polymer preferentially populated the outermost layers of the coating, despite its low content in the blend. However, the self-segregation process and the response to the external environment strongly depended on both the chemistry of the polymer and the type of matrix used for the blend. Additionally, mechanical testing showed that the elastic modulus of SEBS-based coatings was one order of magnitude higher than that of the corresponding PDMS-based coatings. The coatings were subjected to laboratory bioassays with the marine alga Ulva linza. PDMS-based coatings had superior fouling-release properties compared to the SEBS-based coatings.

Ester type banana-shaped liquid crystalline monomers: synthesis and physical properties

New ester-type banana (bent-shaped) monomers, 1,3-phenylene bis[4′-(alken-1-yloxy)-biphenyl-4-carboxylate]s Ia–Vb, with different substituent(s) on the central phenyl ring (H, CH3, Cl or NO2) and alkenyl tails in the side arms (decenyl or undecenyl) were prepared. The analogues IIIa–IVb with 4-chloro- or 4,6-dichloro-substituents exhibited a nematic phase, while Va,Vb with 2-nitro-substituent showed a B7 phase at relatively low temperature. All the compounds were stable, no degradation or polymerization was observed under applied electric fields or heat treatments. Electro-hydrodynamic instabilities were observed in the nematic phase of each sample. In the B7 phase of Vb there was an electro-optical switching in the range 112–114.5 °C with a switching time of about 150 µs at 20 V µm−1 field. At lower temperatures no electro-optical switching occurred, but a ferroelectric-type spontaneous polarization of 22 nC cm−2 could be detected. The bend angle was calculated by the semiempirical CAChe/MOPAC/PM5 method.

Linear viscoelasticity of side chain liquid crystal polymer

Abstract Small amplitude oscillatory shear has been used to study thermotropic liquid-crystalline polymers that have mesogenic groups pendant to flexible backbones. The polymers studied form nematic and smectic glasses, enabling viscoelastic response to be studied over a wide range of frequencies using time-temperature superposition. In contrast to main chain liquid-crystalline polymers, the nematic side chain polymers exhibit linear viscoelastic response over a wide range of strain amplitudes that is independent of thermal and shear histories. Viscoelastic response is very sensitive to smectic-nematic and smectic-isotropic transitions, but insensitive to the nematic-isotropic transition, as time-temperature superposition applies across this transition. We compare viscoelastic data with diffusion data by calculating the time τ that it takes a polymer to diffuse a distance equal to its coil size R (τ=R2/D). At frequencies lower than 1/τ side chain polymers in their nematic show the terminal response charac...