Giancarlo R. Salazar-Banda

AFM studies and electrochemical characterization of boron-doped diamond surfaces modified with metal oxides by the Sol-Gel method

Continuing previous investigations, direct surface modifications of boron-doped diamond (BDD) electrodes with metal oxides (PtOx, RuO2, IrO2 and PbO2) and with some mixed composites were carried out by the Sol-Gel technique. The materials were studied by atomic force microscopy (AFM) to determine their surface topologies and by electrochemical techniques to establish the catalytic activity towards the oxygen evolution reaction (OER) and also, for the PtOx and PtOx-RuO2 composites, the ethanol oxidation reactions in acid media. The stability of PtOx coating covered by a Nafion® film was also tested by long-term operation. The AFM results indicated sites of heterogeneous deposition and the electrochemical studies demonstrated that the active surface area changed considerably with the proposed method of modification. The IrO2/BDD electrode showed the best performance to the OER with the onset of the oxidation current at ~1.4 V, a value 200 mV lower than for the PtOx/BDD electrode. The enhanced stability of PtOx/BDD electrodes achieved by the application of a Nafion® film and already reported in acid media was further proved using the ethanol oxidation reaction. Only a small loss of activity (6%) was observed after 4-hours electrolysis while one-thousand voltammetric cycles left the surface practically unchanged. In addition, preliminary studies for the same reaction on PtOx/BDD and PtOx-RuO2/BDD electrodes demonstrated the excellent activity of these mixed Sol-Gel coatings on the BDD surface and the possibility of further investigations for practical applications.

Sonovoltammetric determination of 4-nitrophenol on diamond electrodes

The sonovoltammetric determination of 4-nitrophenol was studied on a boron-doped diamond electrode. Significant improvements in the analytical sensibility were observed due to electrode surface cleaning and the enhancement in the transport of species to the electrode surface provided by ultrasound. Thus, for the oxidation and reduction process, the limit of detection diminished from 11.7 to 3.87 and from 6.38 to 2.57 µg L-1, respectively.

Comparing atrazine and cyanuric acid electro-oxidation on mixed oxide and boron-doped diamond electrodes

The breakdown of pesticides has been promoted by many methods for clean up of contaminated soil and wastewaters. The main goal is to decrease the toxicity of the parent compound to achieve non-toxic compounds or even, when complete mineralization occurs, carbon dioxide and water. Therefore, electrochemical degradation (potentiostatic and galvanostatic) of both the pesticide atrazine and cyanuric acid (CA) at boron-doped diamond (BDD) and Ti/Ru0.3Ti0.7O2 dimensionally stable anode (DSA®) electrodes, in different supporting electrolytes (NaCl and Na2SO4), is presented with the aim of establishing the influence of the operational parameters on the process efficiency. The results demonstrate that both the electrode material and the supporting electrolyte have a strong influence on the rate of atrazine removal. In the chloride medium, the rate of atrazine removal is always greater than in sulfate under all conditions employed. Furthermore, in the sulfate medium, atrazine degradation was significant only at the BDD electrode. The total organic carbon (TOC) load decreased by 79% and 56% at the BDD and DSA® electrodes, respectively, in the chloride medium. This trend was maintained in the sulfate medium but the TOC removal was lower (i.e. 33% and 13% at BDD and DSA® electrodes, respectively). CA, a stable atrazine degradation intermediate, was also studied and it is efficiently removed using the BDD electrode in both media, mainly when high current densities are employed. The use of the BDD electrode in the chloride medium not only degrades atrazine but also mineralized cyanuric acid leading to the higher TOC removal.

Improved stability of PtOx sol-gel-modified diamond electrodes covered with a Nafion® film

The modification of boron-doped diamond (BDD) electrodes with platinum oxide particles deposited by the Sol-gel method and using several pre- and post-treatments of the surface is described. The electrochemical stability of the resulting catalytic coatings was evaluated by cyclic voltammetry in acid medium and was much greater than those previously reported in the literature for others deposition methods. A thermal pre-treatment of the BDD surface yielded electrodes that retained 91.6% of the coated material after 1000 voltammetric cycles carried out between the water decomposition reactions. The application of a Nafion® film on top of the coating preserved integrally the deposited platinum oxide. The use of such modified electrodes for practical applications is now feasible under the present experimental conditions.

A simple and sensitive detection of diquat herbicide using a dental amalgam electrode: A comparison using the chromatographic technique

This paper describes the use of a dental amalgam electrode (DAE) to evaluate the electrochemical behaviour and to develop an electroanalytical procedure for determination of diquat herbicide in natural water and potato samples. The work was based on the square wave voltammetry responses of diquat, which presented two well-defined and reversible reduction peaks, at -0.56 V (peak 1) and -1.00 V (peak 2). The experimental and voltammetric parameters were optimised, and the analytical curves were constructed and compared to similar curves performed by high performance liquid chromatography coupled to ultraviolet-visible spectrophotometric detector (HPLC/UV-vis). The responses were directly proportional to diquat concentration in a large interval of concentration, and the calculated detection limits were very similar, around 10 microg L(-1) (10 ppb) for voltammetric and chromatographic experiments. These values were lower than the maximum residue limit established for natural water by the Brazilian Environmental Agency. The recovery percentages in pure electrolyte, natural water and potato samples showed values from 70% to 130%, demonstrating that the voltammetric methodology proposed is suitable for determining any contamination by diquat in different samples, minimising the toxic residues due to the use of liquid mercury or the adsorptive process relative to use of other solid surfaces.

Electrochemical oxidation and electroanalytical determination of xylitol at a boron-doped diamond electrode

Xylitol is a reduced sugar with anticariogenic properties used by insulin-dependent diabetics, and which has attracted great attention of the pharmaceutical, cosmetics, food and dental industries. The detection of xylitol in different matrices is generally based on separation techniques. Alternatively, in this paper, the application of a boron-doped diamond (BDD) electrode allied to differing voltammetric techniques is presented to study the electrochemical behavior of xylitol, and to develop an analytical methodology for its determination in mouthwash. Xylitol undergoes two oxidation steps in an irreversible diffusion-controlled process (D=5.05 × 10(-5)cm(2)s(-1)). Differential pulse voltammetry studies revealed that the oxidation mechanism for peaks P1 (3.4 ≤ pH ≤ 8.0), and P2 (6.0 ≤ pH ≤ 9.0) involves transfer of 1H(+)/1e(-), and 1e(-) alone, respectively. The oxidation process P1 is mediated by the (•)OH generated at the BDD hydrogen-terminated surface. The maximum peak current was obtained at a pH of 7.0, and the electroanalytical method developed, (employing square wave voltammetry) yielded low detection (1.3 × 10(-6) mol L(-1)), and quantification (4.5 × 10(-6) mol L(-1)) limits, associated with good levels of repeatability (4.7%), and reproducibility (5.3%); thus demonstrating the viability of the methodology for detection of xylitol in biological samples containing low concentrations.

Sequence-specific electrochemical detection of Alicyclobacillus acidoterrestris DNA using electroconductive polymer-modified fluorine tin oxide electrodes

This study outlines the quantification of low levels of Alicyclobacillus acidoterrestris in pure cultures, since this bacterium is not inactivated by pasteurization and may remain in industrialized foods and beverages. Electroconductive polymer-modified fluorine tin oxide (FTO) electrodes and multiple nanoparticle labels were used for biosensing. The detection of A. acidoterrestris in pure cultures was performed by reverse transcription polymerase chain reaction (RT-PCR) and the sensitivity was further increased by asymmetric nested RT-PCR using electrochemical detection for quantification of the amplicon. The quantification of nested RT-PCR products by Ag/Au-based electrochemical detection was able to detect 2 colony forming units per mL (CFU mL(-1)) of spores in pure culture and low detection and quantification limits (7.07 and 23.6 nM, respectively) were obtained for the target A. acidoterrestris on the electrochemical detection bioassay.

Aplicação do ultra-som em sistemas eletroquímicos: considerações teóricas e experimentais

The aim of this review is to present and discuss the applications of ultrasound in electrochemical systems such as in sonoelectroanalysis and sonoelectrolysis for the electrochemical combustion of organic compounds. Initially, theoretical and experimental aspects are discussed, particularly those related to the enhancement of mass transport and the surface cleaning effects. Some results are included to illustrate alternative geometries for the experimental measurements and the working electrodes used in these systems. In the sequence, the available publications are presented and discussed to demonstrate that ultrasound combined with electrochemical techniques is a powerful set-up for the detection of analytes such as metals and/or organic compounds in hostile media and for the effective destruction of toxic organic substances. At the end, a table summarizes the results already published in the literature.

Determination of 5-aminosalicylic acid in pharmaceutical formulations by square wave voltammetry at pencil graphite electrodes

An analytical method for the determination of the anti-inflammatory drug 5-aminosalicylic acid (5-ASA) in pharmaceutical formulations using square wave voltammetry at pencil graphite electrodes was developed. After the optimization of the experimental conditions, calibration curves were obtained in the linear concentration range from 9.78 × 10-7 to 7.25 × 10-5 mol L-1 resulting in a limit of detection of 2.12 ± 0.05 x 10-8 mol L-1. Statistical tests showed that the concentrations of 5-ASA in commercial tablets and enemas obtained with the proposed voltammetric method agreed with HPLC values at a 95% confidence level.

Wet chemical synthesis of rare earth-doped barium titanate nanoparticles

Barium titanate (BaTiO3) is a common ferroelectric material with perovskite structure widely used for the production of a variety of electro-optical devices. When doping with rare earth elements, very interesting characteristics can be attributed to BaTiO3. Among the methods used to synthesize BaTiO3, wet chemical approaches are the most suitable for preparing homogenous and pure nanostructured materials. In this sense, the present article aims to summarize the state-of-the-art of the most relevant wet chemical routes for the synthesis of nanocrystalline BaTiO3 doped with rare earth (RE) ions (BaTiO3:RE), which include the following: sol–gel, sol–emulsion–gel, Pechini, solvothermal/hydrothermal, and co-precipitation methods. The influence of each method on morphology and particle size, as well as on the dielectric and/or luminescent properties of the powders is discussed.