Gildas Rethore

A novel injectable, cohesive and toughened Si-HPMC (silanized-hydroxypropyl methylcellulose) composite calcium phosphate cement for bone substitution.

This study reports on the incorporation of the self-setting polysaccharide derivative hydrogel (silanized-hydroxypropyl methylcellulose, Si-HPMC) into the formulation of calcium phosphate cements (CPCs) to develop a novel injectable material for bone substitution. The effects of Si-HPMC on the handling properties (injectability, cohesion and setting time) and mechanical properties (Youngs modulus, fracture toughness, flexural and compressive strength) of CPCs were systematically studied. It was found that Si-HPMC could endow composite CPC pastes with an appealing rheological behavior at the early stage of setting, promoting its application in open bone cavities. Moreover, Si-HPMC gave the composite CPC good injectability and cohesion, and reduced the setting time. Si-HPMC increased the porosity of CPCs after hardening, especially the macroporosity as a result of entrapped air bubbles; however, it improved, rather than compromised, the mechanical properties of composite CPCs, which demonstrates a strong toughening and strengthening effect. In view of the above, the Si-HPMC composite CPC may be particularly promising as bone substitute material for clinic application.

A simple and effective approach to prepare injectable macroporous calcium phosphate cement for bone repair: Syringe-foaming using a viscous hydrophilic polymeric solution

UNLABELLED In this study, we propose a simple and effective strategy to prepare injectable macroporous calcium phosphate cements (CPCs) by syringe-foaming via hydrophilic viscous polymeric solution, such as using silanized-hydroxypropyl methylcellulose (Si-HPMC) as a foaming agent. The Si-HPMC foamed CPCs demonstrate excellent handling properties such as injectability and cohesion. After hardening the foamed CPCs possess hierarchical macropores and their mechanical properties (Youngs modulus and compressive strength) are comparable to those of cancellous bone. Moreover, a preliminary in vivo study in the distal femoral sites of rabbits was conducted to evaluate the biofunctionality of this injectable macroporous CPC. The evidence of newly formed bone in the central zone of implantation site indicates the feasibility and effectiveness of this foaming strategy that will have to be optimized by further extensive animal experiments. STATEMENT OF SIGNIFICANCE A major challenge in the design of biomaterial-based injectable bone substitutes is the development of cohesive, macroporous and self-setting calcium phosphate cement (CPC) that enables rapid cell invasion with adequate initial mechanical properties without the use of complex processing and additives. Thus, we propose a simple and effective strategy to prepare injectable macroporous CPCs through syringe-foaming using a hydrophilic viscous polymeric solution (silanized-hydroxypropyl methylcellulose, Si-HPMC) as a foaming agent, that simultaneously meets all the aforementioned aims. Evidence from our in vivo studies shows the existence of newly formed bone within the implantation site, indicating the feasibility and effectiveness of this foaming strategy, which could be used in various CPC systems using other hydrophilic viscous polymeric solutions.

Interplay of thermal and covalent gelation of silanized hydroxypropyl methyl cellulose gels

Silanized hydroxypropyl methyl cellulose (Si-HPMC) is a biocompatible polysaccharide that forms a covalently crosslinked hydrogel at all temperatures due to silanol condensation. Unmodified HPMC forms reversible turbid physical gels when heated above 55°C. The interaction between thermal gelation and covalent crosslinking of Si-HPMC was investigated with rheology, turbidity and microscopy. Thermal gelation of the HPMC backbone was found to reinforce Si-HPMC gels at room temperature. However, simultaneous thermal and covalent crosslinking at higher temperatures led to weaker turbid gels at room temperature. The effect of the pH and the addition of orthophosphate on the elastic modulus and the gelation kinetics was investigated.

Laponite nanoparticle-associated silated hydroxypropylmethyl cellulose as an injectable reinforced interpenetrating network hydrogel for cartilage tissue engineering

Articular cartilage is a connective tissue which does not spontaneously heal. To address this issue, biomaterial-assisted cell therapy has been researched with promising advances. The lack of strong mechanical properties is still a concern despite significant progress in three-dimensional scaffolds. This articles objective was to develop a composite hydrogel using a small amount of nano-reinforcement clay known as laponites. These laponites were capable of self-setting within the gel structure of the silated hydroxypropylmethyl cellulose (Si-HPMC) hydrogel. Laponites (XLG) were mixed with Si-HPMC to prepare composite hydrogels leading to the development of a hybrid interpenetrating network. This interpenetrating network increases the mechanical properties of the hydrogel. The in vitro investigations showed no side effects from the XLG regarding cytocompatibility or oxygen diffusion within the composite after cross-linking. The ability of the hybrid scaffold containing the composite hydrogel and chondrogenic cells to form a cartilaginous tissue in vivo was investigated during a 6-week implantation in subcutaneous pockets of nude mice. Histological analysis of the composite constructs revealed the formation of a cartilage-like tissue with an extracellular matrix containing glycosaminoglycans and collagens. Overall, this new hybrid construct demonstrates an interpenetrating network which enhances the hydrogel mechanical properties without interfering with its cytocompatibility, oxygen diffusion, or the ability of chondrogenic cells to self-organize in the cluster and produce extracellular matrix components. This composite hydrogel may be of relevance for the treatment of cartilage defects in a large animal model of articular cartilage defects. STATEMENT OF SIGNIFICANCE Articular cartilage is a tissue that fails to heal spontaneously. To address this clinically relevant issue, biomaterial-assisted cell therapy is considered promising but often lacks adequate mechanical properties. Our objective was to develop a composite hydrogel using a small amount of nano reinforcement (laponite) capable of gelling within polysaccharide based self-crosslinking hydrogel. This new hybrid construct demonstrates an interpenetrating network (IPN) which enhances the hydrogel mechanical properties without interfering with its cytocompatibility, O2 diffusion and the ability of chondrogenic cells to self-organize in cluster and produce extracellular matrix components. This composite hydrogel may be of relevance for the treatment of cartilage defects and will now be considered in a large animal model of articular cartilage defects.

Microgels of silylated HPMC as a multimodal system for drug co-encapsulation

Combined therapy is a global strategy developed to prevent drug resistance in cancer and infectious diseases. In this field, there is a need of multifunctional drug delivery systems able to co-encapsulate small drug molecules, peptides, proteins, associated to targeting functions, nanoparticles. Silylated hydrogels are alkoxysilane hybrid polymers that can be engaged in a sol-gel process, providing chemical cross linking in physiological conditions, and functionalized biocompatible hybrid materials. In the present work, microgels were prepared with silylated (hydroxypropyl)methyl cellulose (Si-HPMC) that was chemically cross linked in soft conditions of pH and temperature. They were prepared by an emulsion templating process, water in oil (W/O), as microreactors where the condensation reaction took place. The ability to functionalize the microgels, so-called FMGs, in a one-pot process, was evaluated by grafting a silylated hydrophilic model drug, fluorescein (Si-Fluor), using the same reaction of condensation. Biphasic microgels (BPMGs) were prepared to evaluate their potential to encapsulate lipophilic model drug (Nile red). They were composed of two separate compartments, one oily phase (sesame oil) trapped in the cross linked Si-HPMC hydrophilic phase. The FMGs and BPMGs were characterized by different microscopic techniques (optic, epi-fluorescence, Confocal Laser Scanning Microscopy and scanning electronic microscopy), the mechanical properties were monitored using nano indentation by Atomic Force Microscopy (AFM), and different preliminary tests were performed to evaluate their chemical and physical stability. Finally, it was demonstrated that it is possible to co-encapsulate both hydrophilic and hydrophobic drugs, in silylated microgels, that were physically and chemically stable. They were obtained by chemical cross linking in soft conditions, and without surfactant addition during the emulsification process. The amount of drug loaded was in favor of further biological activity. Mechanical stimulations should be necessary to trigger drug release.

Assessing glucose and oxygen diffusion in hydrogels for the rational design of 3D stem cell scaffolds in regenerative medicine

Hydrogels are attractive biomaterials for replicating cellular microenvironments, but attention needs to be given to hydrogels diffusion properties. A large body of literature shows the promise of hydrogels as 3D culture models, cell expansion systems, cell delivery vehicles, and tissue constructs. Surprisingly, literature seems to have overlooked the important effects of nutrient diffusion on the viability of hydrogel‐encapsulated cells. In this paper, we present the methods and results of an investigation into glucose and oxygen diffusion into a silated‐hydroxypropylmethylcellulose (Si‐HPMC) hydrogel. Using both an implantable glucose sensor and implantable oxygen sensor, we continuously monitored core glucose concentration and oxygen concentration at the centre of hydrogels. We demonstrated that we could tune molecular transport in Si‐HPMC hydrogel by changing the polymer concentration. Specifically, the oxygen diffusion coefficient was found to significantly decrease from 3.4 × 10−10 to 2.4 × 10−10 m2 s−1 as the polymer concentration increased from 1% to 4% (w/v). Moreover, it was revealed during in vitro culture of cellularized hydrogels that oxygen depletion occurred before glucose depletion, suggesting oxygen diffusion is the major limiting factor for cell survival. Insight was also gained into the mechanism of action by which oxygen and glucose diffuse. Indeed, a direct correlation was found between the average polymer crosslinking node size and glucose parameters, and this correlation was not observed for oxygen. Overall, these experiments provide useful insights for the analysis of nutrient transport and gas exchange in hydrogels and for the development of future cellular microenvironments based on Si‐HPMC or similar polysaccharide hydrogels.

A Cellulose/Laponite Interpenetrated Polymer Network (IPN) Hydrogel: Controllable Double-Network Structure with High Modulus

Laponite XLS™, which is a synthetic clay of nanometric dimensions containing a peptizing agent, has been associated with silanized hydroxypropylmethylcellulose (Si-HPMC) to form, after crosslinking, a novel composite hydrogel. Different protocols of sample preparation were used, leading to different morphologies. A key result was that the storage modulus of Si-HPMC/XLS composite hydrogel could be increased ten times when compared to that of pure Si-HPMC hydrogel using 2 wt % of Laponite. The viscoelastic properties of the composite formulations indicated that chemical and physical network structures co-existed in the Si-HPMC/XLS composite hydrogel. Images that were obtained from confocal laser scanning microscopy using labelled Laponite XLS in the composite hydrogels show two co-continuous areas: red light area and dark area. The tracking of fluorescent microspheres motions in the composite formulations revealed that the red-light area was a dense structure, whereas the dark area was rather loose without aggregated Laponite. This novel special double-network structure facilitates the composite hydrogel to be an adapted biomaterial for specific tissue engineering. Unfortunately, cytotoxicity’s assays suggested that XLS Laponites are cytotoxic at low concentration. This study validates that the hybrid interpenetrated network IPN hydrogel has a high modulus that has adapted for tissue engineering, but the cell’s internalization of Laponites has to be controlled.

Evaluation of a hydrogel membrane on bone regeneration in furcation periodontal defects in dogs

The aim of the study was to evaluate bone regeneration using a canine model with surgically created periodontal defects filled for 12 weeks using a stratified biomaterial consisting in a biphasic calcium phosphate (BCP) covered with a crosslinking hydrogel acting as polymer membrane of silated hydroxypropyl methylcellulose (Si-HPMC) as the tested new concept. Bilateral, critical-sized, defects were surgically created at the mandibular premolar teeth of six adult beagle dogs. The defects were randomly allocated and: (i) left empty for spontaneous healing or filled with: (ii) BCP and a collagen membrane; (iii) BCP and hydrogel Si-HPMC membrane. At 12 weeks, the experimental conditions resulted in significantly enhanced bone regeneration in the test BCP/Si-HPMC group. Within the limits of this study, we suggest that the hydrogel Si-HPMC may act as an occlusive barrier to protect bone area from soft connective tissue invasion and then effectively contribute to enhance bone regeneration.

Functionalisation of Polysaccharides for the Purposes of Electrospinning: A Case Study Using HPMC and Si-HPMC

Hydrogels are a suitable scaffold material for a variety of tissue engineering applications. However, these materials have a weak structure and require reinforcement. Integrating electrospun fibers could strengthen material properties. This study created fibers and evaluated the influence of the presence of polar head groups within a polysaccharide backbone following functionalization: silated-hydroxypropyl methylcellulose (Si-HPMC). Electrospinning is a multi-parameter, step by step process that requires optimization of solution and process parameters to understand and control the process. Fibers were created for 2%–3% wt/v solutions in water and ethanol. Viscosities of solutions were correlated with spinnability. Variations on process parameters did not reveal major variation on fiber morphology. Once controlled, the process was used for HPMC/Si-HPMC mixture solutions. Solubilization and dilution of Si-HPMC were made with common solvents for electrospinning. Two forms of polymer conformation were electrospun: silanol ending and silanolate ending. Microstructures and resulting nanofibers were analyzed by scanning electron microscopy (SEM) and Energy Dispersive Analysis (EDX). The results show the feasibility of our strategy for creating nanofibers and the influence of polar head groups on electrospinnability.

Tissue Engineering and Regenerative Medicine

Adequate cellular in-growth into biomaterials is one of the fundamental requirements in regenerative medicine. Type-I-collagen is the most commonly used material for soft tissue engineering, because it is nonimmunogenic and a highly porous network for cellular support. However, adequate cell in-growth and cell seeding has been suboptimal. Different densities of collagen scaffolds (0.3% to 0.8% (w/v)) with/without polymer knitting (poly-caprolactone (PCL)) were prepared. The structure of collagen scaffolds was characterized using scanning electronic microscopy (SEM) and HE staining. The mechanical strength of hybrid scaffolds was determined using tensile strength analysis. Cellular penetration and interconnectivity were evaluated using fluorescent bead distribution and human bladder smooth muscle cells and urothelium seeding. SEM and HE analysis showed the honeycomb structure and the hybrid scaffolds were adequately connected. The hybrid scaffolds were much stronger than collagen alone. The distribution of the beads and cells were highly dependent on the collagen density: at lower densities the beads and cells were more evenly distributed and penetrated deeper into the scaffold. The lower density collagen scaffolds showed remarkably deeper cellular penetration and by combining it with PCL knitting the tensile strength was enhanced. This study indicated that a 0.4% hybrid scaffold strengthened with knitting achieved the best cellular distribution.Human adult heart harbors a population of resident progenitor cells that can be isolated by Sca-1 antibody and expanded in culture. These cells can differentiate into cardiomyocytes and vascular cells in vitro and contribute to cardiac regeneration in vivo. However, when directly injected as single cell suspension, the survival rate and retention is really poor, less than 1% of injected cells being detectable in the hosttissue within few weeks. The present study aimed at investigating the possibility to produce scaffoldless, thick cardiac progenitor cell-derived cardiac patches by thermo-responsive technology. Human cardiac progenitors obtained from the auricles of patients were cultured as scaffoldless engineered tissues fabricated using temperature-responsive surfaces obtained by poly-N-isopropylacrylamide (PNIPAAm) surface immobilization. In the engineered tissue, progenitor cells established proper three-dimensional intercellular relationships and produced abundant extracellular matrix, while preserving their phenotype and plasticity. Cell phenotype and viability within the 3D construct were followed for 1 week, showing that no significant differentiation or apoptotic events occurred within the construct. After engineered tissues were leant on visceral pericardium, a number of cells migrated into the myocardium and in the vascular walls, where they integrated in the respective textures. The study demonstrates the suitability of such approach to deliver stem cells.Spinal cord injury and repair is one of the important focus areas in tissue regeneration. Mechanical trauma caused due to factors such as contusion, compression or involuntary stretching induce post-traumatic secondary tissue damage in many Spinal Cord Injury (SCI) patients. Therefore, there is a need for scaffolds that provide a conducive threedimensionsal (3D) environment for injured cells to attach and grow. In this study we propose to synthesize 3D polymeric scaffolds in order to study the mechanical and adhesive properties & the nature of the interactions between hyaluronan-based (HY) biomaterials and cells and tissues both in vitroandin vivo. Here we have synthesized 3D HY-based hydrogels with robust mechanical and adhesive properties and demonstrate the use of this material for neuronal-related applications such as the treatment of SCI. Cell culture and survivability studies were done with NSC-34 cells. Live/Dead assay performed on the cells revealed significant differences in the staining of live cells and showed increased viability and proliferation. The number of live cells in the HY-based hydrogels with 0.1% collagen showed higher cell numbers compared with the other hydrogels. In this study we show that Injectable HYbased hydrogels with high elasticity, comparable to the mechanical properties of nervous tissue have been used in this study to study their biocompatibility and neuroprotective properties and they show better affinity for neuronal cells.Calcium phosphates (CaP) obtained by biomineralisation in Simulated Boby Fluid have been used for decades to assess the mineralisation capability of biomaterials. Recently, they have been envisioned as potential agents to promote bone formation. In this study, we have fabricated and coated with calcium phosphate melt electrospun scaffolds whereby macropores permit adequate cell migration and nutrient transfer. We have systematically investigated the effect of coating and osteoinduction onto the response of ovine osteoblasts and we observed that the coating up-regulated alkaline phosphatase activity regardless of the in vitro culture conditions. Micro Computed Tomography revealed that only scaffolds cultured in an osteoinductive cocktail were capable of depositing mineralised matrix, and that CaP coated scaffolds were more efficient at promoting mineralisation. Theses scaffolds were subcutaneously implanted in athymic rats and this demonstrated that the osteoinduction was a pre-requisite for bone formation in this ectopic model. It showed that although the bone formation was not significantly different after 8 weeks, the CaP coated scaffolds were superior at inducing bone formation as evidenced by higher levels of mineralisation at earlier time points. This work demonstrated that CaP coating is not sufficient to induce bone formation; however the combination of osteoinduction and CaP coating resulted in earlier bone formation in an ectopic model.Introduction: Bladder regeneration using minced bladder mucosa is an alternative to costly and time-consuming conventional in vitro culturing of urothelial cells. In this method, the uroepithelium ...