Giuliano Freddi

Biodegradable Materials Based on Silk Fibroin and Keratin

Wool and silk were dissolved and used for the preparation of blended films. Two systems are proposed: (1) blend films of silk fibroin and keratin aqueous solutions and (2) silk fibroin and keratin dissolved in formic acid. The FTIR spectra of pure films cast from aqueous solutions indicated that the keratin secondary structure mainly consists of alpha-helix and random coil conformations. The IR spectrum of pure SF is characteristic of films with prevalently amorphous structure (random coil conformation). Pure keratin film cast from formic acid shows an increase in the amount of beta-sheet and disordered keratin structures. The FTIR pattern of SF dissolved in formic acid is characteristic of films with prevalently beta-sheet conformations with beta-sheet crystallites embedded in an amorphous matrix. The thermal behavior of the blends confirmed the FTIR results. DSC curve of pure SF is typical of amorphous SF and the curve of pure keratin show the characteristic melting peak of alpha-helices for the aqueous system. These patterns are no longer observed in the films cast from formic acid due to the ability of formic acid to induce crystallization of SF and to increase the amount of beta-sheet structures on keratin. The nonlinear trend of the different parameters obtained from FTIR analysis and DSC curves of both SF/keratin systems indicate that when proteins are mixed they do not follow additives rules but are able to establish intermolecular interactions. Degradable polymeric biomaterials are preferred candidates for medical applications. It was investigated the degradation behavior of both SF/keratin systems by in vitro enzymatic incubation with trypsin. The SF/keratin films cast from water underwent a slower biological degradation than the films cast from formic acid. The weight loss obtained is a function of the amount of keratin in the blend. This study encourages the further investigation of the type of matrices presented here to be applied whether in scaffolds for tissue engineering or as controlled release drug delivery vehicles.

Structure and physical properties of silk fibroin/polyacrylamide blend films

This article deals with the characterization of blend films obtained by mixing silk fibroin (SF) and polyacrylamide (PAAm). The DSC curves of SF/PAAm blend films showed overlapping of the main thermal transitions characteristic of the individual polymers. The exothermic peak at 218°C, assigned to the β-sheet crystallization of silk fibroin, slightly shifted to a lower temperature by blending. The weight-retention properties (TG) of the blend films were intermediate between those of the two constituents. The TMA response was indicative of a higher thermal stability of the blend films, even at low PAAm content (≤25%), the final breaking occurring at about 300°C (100°C higher than pure SF film). The peak of dynamic loss modulus of silk fibroin at 193°C gradually shifted to lower temperature in the blend films, suggesting an enhancement of the molecular motion of the fibroin chains induced by the presence of PAAm. Changes in the NH stretching region of silk fibroin were detected by FTIR analysis of blend films. These are attributable to disturbance of the hydrogen bond pattern of silk fibroin and formation of new hydrogen bonds with PAAm. The values of strength and elongation at break of blend films slightly improved at 20–25% PAAm content. A sea–island structure was observed by examining the air surface of the blend films by scanning electron microscopy.

Compliant electrospun silk fibroin tubes for small vessel bypass grafting.

Processing silk fibroin (SF) by electrospinning offers a very attractive opportunity for producing three-dimensional nanofibrillar matrices in tubular form, which may be useful for a biomimetic approach to small calibre vessel regeneration. Bypass grafting of small calibre vessels, with a diameter less than 6mm, is performed mainly using autografts, like the saphenous vein or internal mammary artery. At present no polymeric grafts made of SF are commercially available, mainly due to inadequate properties (low compliance and lack of endothelium cells). The aim of this work was to electrospin SF into tubular structures (Ø=6mm) for small calibre vessel grafting, characterize the morphological, chemico-physical and mechanical properties of the electrospun SF structures and to validate their potential to interact with cells. The morphological properties of electrospun SF nanofibres were investigated by scanning electron microscopy. Chemico-physical analyses revealed an increase in the crystallinity of the structure of SF nanofibres on methanol treatment. Mechanical tests, i.e. compliance and burst pressure measurements, of the electrospun SF tubes showed that the inner pressure to radial deformation ratio was linear for elongation up to 15% and pressure up to 400 mm Hg. The mean compliance value between 80 and 120 mm Hg was higher than the values reported for both Goretex(R) and Dacron(R) grafts and for bovine heterografts, but still slightly lower than those of saphenous and umbilical vein, which nowadays represent the gold standard for the replacement of small calibre arteries. The electrospun tubes resisted up to 575+/-17 mmHg, which is more than four times the upper physiological pressure of 120 mmHg and more than twice the pathological upper pressures (range 180-220 mmHg). The in vitro tests showed a good cytocompatibility of the electrospun SF tubes. Therefore, the electrospun SF tubes developed within this work represent a suitable candidate for small calibre blood vessel replacement.

Swelling and dissolution of silk fibroin (Bombyx mori) in N-methyl morpholine N-oxide

Bombyx mori silk fibers were dissolved in N-methyl morpholine N-oxide (MMNO), an organic cyclic amine oxide used for the solvent spinning of regenerated cellulosic fibers. The commercial MMNO monohydrate used in this study as a solvent for silk is a hygroscopic compound crystalline at room temperature, which becomes an active solvent after melting at 76 degrees C. The degree of hydration of MMNO was checked by DSC measurements. The solvation power of MMNO towards silk fibroin drastically decreased at a water content > or = 20-21% w/w. Dissolution of silk required both thermal and mechanical energy. The optimum temperature was 100 degrees C. At lower temperatures dissolution proceeded very slowly. At higher temperatures, rapid depolymerization of silk fibroin occurred. The value of the Flory-Huggins interaction parameter chi for the MMNO-H2O-silk fibroin system was -8.5, suggesting that dissolution is a thermodynamically favored process. The extent of degradation of silk fibroin was assessed by measuring the intrinsic viscosity and determining the amino acid composition of silk after regeneration with an aqueous methanol solution, which was effective in removing the solvent and coagulating silk. Regenerated silk fibroin membranes were characterized by infrared spectroscopy, differential scanning calorimetry and scanning electron microscopy. The prevailing molecular conformation of silk fibroin chains was the beta-sheet structure, as shown by the intense amide I-III bands at 1704, 1627, 1515, 1260, and 1230 cm(-1). The value of the I1260/I1230 intensity ratio (crystallinity index) was 0.68, comparable to that of the fibers. The DSC thermogram was characteristic of a silk fibroin material with unoriented beta-sheet crystalline structure, with an intense decomposition endotherm at 294 degrees C. The SEM examination of fractured surfaces showed the presence of a dense microstructure with a very fine texture formed by densely packed roundish particles of about 100-200 nm diameter.

Structure and molecular conformation of tussah silk fibroin films: Effect of heat treatment

Structural changes of tussah (Antheraea pernyi) silk fibroin films induced by heat treatment were studied as a function of the treatment temperature in the range 200–250°C. The DSC curve of tussah films with α-helix molecular conformation displayed characteristic endo and exo peaks at 216 and 226°C, respectively. These peaks first weakened and then completely disappeared after heating at 230°C. Accordingly, the TMA thermal shrinkage at 206°C disappeared when the films were heated at 230°C. The onset of weight loss was monitored at 210°C by means of TG measurements. X-ray diffraction profiles gradually changed from α-helix to β-sheet crystalline structure as the treatment temperature increased from 200 to 250°C. On raising the heating temperature above 200°C, the intensity of IR and Raman bands characteristic of β-sheet conformation increased in the whole ranges of amide and skeletal modes. The sample treated at 200°C showed a spectral pattern intermediate between α-helix and β-sheet molecular conformation. The IR marker band for random coil structure, still detectable at 200°C, disappeared at higher treatment temperatures. Spectral changes attributable to the onset of thermal degradation appeared at 230°C.

Enzymatic surface modification and functionalization of PET: A water contact angle, FTIR, and fluorescence spectroscopy study

The purpose of this study was to investigate the changes induced by a lypolytic enzyme on the surface properties of polyethylene terephthalate (PET). Changes in surface hydrophilicity were monitored by means of water contact angle (WCA) measurements. Fourier Transform Infrared spectroscopy (FTIR) in the Attenuated Total Reflectance mode (ATR) was used to investigate the structural and conformational changes of the ethylene glycol and benzene moieties of PET. Amorphous and crystalline PET membranes were used as substrate. The lipolytic enzyme displayed higher hydrolytic activity towards the amorphous PET substrate, as demonstrated by the decrease of the WCA values. Minor changes were observed on the crystalline PET membrane. The effect of enzyme adhesion was addressed by applying a protease after‐treatment which was able to remove the residual enzyme protein adhering to the surface of PET, as demonstrated by the behavior of WCA values. Significant spectral changes were observed by FTIR–ATR analysis in the spectral regions characteristic of the crystalline and amorphous PET domains. The intensity of the crystalline marker bands increased while that of the amorphous ones decreased. Accordingly, the crystallinity indexes calculated as band intensity ratios (1,341/1,410 cm−1 and 1,120/1,100 cm−1) increased. Finally, the free carboxyl groups formed at the surface of PET by enzyme hydrolysis were esterified with a fluorescent alkyl bromide, 2‐(bromomethyl)naphthalene (BrNP). WCA measurements confirmed that the reaction proceeded effectively. The fluorescence results indicate that the enzymatically treated PET films are more reactive towards BrNP. FTIR analysis showed that the surface of BrNP‐modified PET acquired a more crystalline character. Biotechnol. Bioeng. 2009;103: 845–856.

Physical properties and dyeability of silk fibers degummed with citric acid.

Silk fibers from Bombyx mori silkworm was degummed with different concentration of citric acid, and the physical properties and fine structure were investigated to elucidate the effects of citric acid treatment. The silk sericin removal percentage was almost 100% after degumming with 30% citric acid which resulted in a total weight loss of 25.4% in the silk fibers. The surface morphology of silk fiber degummed with citric acid was very smooth and fine, showed perfect degumming like traditional soap-alkali method. The tensile strength of silk fiber was increased after degumming with citric acid (507MPa), where as the traditional soap-alkali method causes to decrease the strength about half of the control silk fiber (250MPa). The molecular conformation estimated by Fourier transform infrared spectroscopy and the crystalline structure evaluated from X-ray diffraction curve stayed unchanged regardless of the degumming with citric acid and soap. The dye uptake percentage of silk fiber degummed with citric acid decreased slightly, about 4.2%. On the other hand, the dye uptake percentage of silk degummed with soap was higher which indicates the disordering of the molecular orientation of the laterally ordered structure, accompanied with the partial hydrolysis of silk fibroin molecules by the alkali action of soap. The thermal properties were greatly enhanced by soap and citric acid degumming agents. Dynamic mechanical thermal analysis showed silk degummed with citric acid is more stable in higher temperature than that of soap. With heating at above 300 degrees C, the silk degummed with citric acid shows an increase in storage modulus and an onset of tan delta peaks at 325 degrees C and the melt flow of the sample was inhibited. The degumming of silk fibers with citric acid is safe and the results obtained are quite promising as a basis for possible future industrial application.

Binding of Co(II) and Cu(II) cations to chemically modified wool fibres: an IR investigation

Wool fibres were modified by treatment with tannic acid (TA) solution or by acylation with ethylenediaminetetraacetic (EDTA) dianhydride. The unmodified and modified fibres were subsequently treated with Cu 2þ and Co 2þ solutions, at alkaline pH, and analysed by Attenuated Total Reflectance, ATR/IR spectroscopy to evaluate the changes induced in the structure of the fibre by metal binding. The spectral changes were correlated to metal adsorption results obtained by Inductive Coupled PlasmaAtomic Emission Spectrometry (ICP-AES). The IR results were discussed in relation to our previous findings on the metal binding mode of Bombyx mori and Tussah silk fibres; the changes observed in the spectra were explained by considering the different affinity of the fibres for the modifying reagent and the amount of the metal absorbed. More relevant spectral changes were observed upon Cu 2þ complexation rather than Co 2þ complexation, according to the metal absorption results. The most relevant changes were observed for the EDTAmodified wool sample treated with Cu 2þ , according to the higher affinity of wool for EDTA. The IR spectra were quantitatively evaluated by the intensity ratio between the Amide I and Amide II bands (IAmideI/IAmideII) and its trend as a function of metal absorption was reported. The present investigation demonstrated that the interaction between fibre and metal and the subsequent fibre modification depend on the chemical nature of the fibre, the metal cation and the modifying reagent. q 2003 Elsevier Science B.V. All rights reserved.

Silk fibroin derived polypeptide-induced biomineralization of collagen.

Silk fibroin (SF) is extensively investigated in osteoregenerative therapy as it combines extraordinary mechanical properties and directs calcium-phosphate formation. However, the role of the peptidic fractions in inducing the protein mineralization has not been previously decoded. In this study, we investigated the mineralization of fibroin-derived polypeptides (FDPs), which were obtained through the chymotryptic separation of the hydrophobic crystalline (Cp) fractions and of the hydrophilic electronegative amorphous (Cs) fractions. When immersed in simulated body fluid (SBF), only Cs fragments demonstrated the formation of carbonated apatite, providing experimental evidence that the mineralization of SF is dictated exclusively by its electronegative amino-acidic sequences. The potential of Cs to conceptually mimic the role of anionic non-collagenous proteins in biomineralization processes was investigated via their incorporation (up to 10% by weight) in bulk osteoid-like dense collagen (DC) gels. Within 6 h in SBF, apatite was formed in DC-Cs hybrid gels, and by day 7, carbonated hydroxylapatite crystals were extensively formed. This accelerated 3-D mineralization resulted in a nine-fold increase in the compressive modulus of the hydrogel. The tailoring of the mineralization and mechanical properties of hydrogels through hybridization with FDPs could potentially have a significant impact on cell delivery and bone regenerative medicine.

Vascular Tissue Engineering: Recent Advances in Small Diameter Blood Vessel Regeneration

Cardiovascular diseases are the leading cause of mortality around the globe. The development of a functional and appropriate substitute for small diameter blood vessel replacement is still a challenge to overcome the main drawbacks of autografts and the inadequate performances of synthetic prostheses made of polyethylene terephthalate (PET, Dacron) and expanded polytetrafluoroethylene (ePTFE, Goretex). Therefore, vascular tissue engineering has become a promising approach for small diameter blood vessel regeneration as demonstrated by the increasing interest dedicated to this field. This review is focused on the most relevant and recent studies concerning vascular tissue engineering for small diameter blood vessel applications. Specifically, the present work reviews research on the development of tissue-engineered vascular grafts made of decellularized matrices and natural and/or biodegradable synthetic polymers and their realization without scaffold.