Gregory Gershinsky

Mg rechargeable batteries: an on-going challenge

The first working Mg rechargeable battery prototypes were ready for presentation about 13 years ago after two breakthroughs. The first was the development of non-Grignard Mg complex electrolyte solutions with reasonably wide electrochemical windows in which Mg electrodes are fully reversible. The second breakthrough was attained by demonstrating high-rate Mg cathodes based on Chevrel phases. These prototypes could compete with lead–acid or Ni–Cd batteries in terms of energy density, very low self-discharge, a wide temperature range of operation, and an impressive prolonged cycle life. However, the energy density and rate capability of these Mg battery prototypes were not attractive enough to commercialize them. Since then we have seen gradual progress in the development of better electrolyte solutions, as well as suggestions of new cathodes. In this article we review the recent accumulated experience, understandings, new strategies and materials, in the continuous R&D process of non-aqueous Mg batteries. This paper provides a road-map of this field during the last decade.

Electrochemical and Spectroscopic Analysis of Mg2+ Intercalation into Thin Film Electrodes of Layered Oxides: V2O5 and MoO3

Electrochemical, surface, and structural studies related to rechargeable Mg batteries were carried out with monolithic thin-film cathodes comprising layered V2O5 and MoO3. The reversible intercalation reactions of these electrodes with Mg ion in nonaqueous Mg salt solutions were explored using a variety of analytical tools. These included slow-scan rate cyclic voltammetry (SSCV), chrono-potentiometry (galvanostatic cycling), Raman and photoelectron spectroscopies, high-resolution microscopy, and XRD. The V2O5 electrodes exhibited reversible Mg-ion intercalation at capacities around 150-180 mAh g(-1) with 100% efficiency. A capacity of 220 mAh g(-1) at >95% efficiency was obtained with MoO3 electrodes. By applying the electrochemical driving force sufficiently slowly it was possible to measure the electrodes at equilibrium conditions and verify by spectroscopy, microscopy, and diffractometry that these electrodes undergo fully reversible structural changes upon Mg-ion insertion/deinsertion cycling.

Fluoroethylene carbonate as an important component in electrolyte solutions for high-voltage lithium batteries: role of surface chemistry on the cathode.

The effect of fluorinated ethylene carbonate (FEC) as a cosolvent in alkyl carbonates/LiPF6 on the cycling performance of high-voltage (5 V) cathodes for Li-ion batteries was investigated using electrochemical tools, X-ray photoelectron spectroscopy (XPS), and high-resolution scanning electron microscopy (HRSEM). An excellent cycling stability of LiCoPO4/Li, LiNi0.5Mn1.5O4/Si, and LiCoPO4/Si cells and a reasonable cycling of LiCoPO4/Si cells was achieved by replacing the commonly used cosolvent ethylene carbonate (EC) by FEC in electrolyte solutions for high-voltage Li-ion batteries. The roles of FEC in the improvement of the cycling performance of high-voltage Li-ion cells and of surface chemistry on the cathode are discussed.

Operando electron magnetic measurements of Li-ion batteries

One of the challenges in the development of batteries consists of investigating new electrode materials and comprehending the mechanism of lithium uptake. Herein, we report on the first operando measurements of electron magnetism in a battery during cycling. We have succeeded in designing a non-magnetic cell and have investigated the lithiation mechanism of FeSb2, a high energy density anode material. The stepwise increase of the magnetic moment reveals an increase of amorphous Fe nanoparticle size, while Sb undergoes reversible alloying with Li.

On the impact of Vertical Alignment of MoS 2 for Efficient Lithium Storage

Herein, we report energy storage devices, which are based on densely packed, vertically aligned MoS2 (VA-MoS2) or planar oriented MoS2 (PO-MoS2) and compare their electrochemical performances. The VA-MoS2 films have been processed by chemical vapor deposition (CVD) to reach unprecedented micron-scale thick films while maintaining the vertical alignment for the whole thickness. The VA-MoS2 and the PO-MoS2 films form a high-performance Li-ion electrode, reaching the theoretical limits of reversible capacity for this material (800 mAh/g; twice the specific capacity of graphite). The vertical alignment allows faster charge-discharge rates while maintaining a high specific capacity (C-rate measurements). Noteworthy, the reversible cycling of the Li-ion electrode also benefits from the vertical alignment. In this article, we present the full synthesis, structural and electrochemical characterization of VA-MoS2 along with the properties of PO-MoS2 to deconvolute the intrinsic properties of MoS2 from the influence of the layers’ orientation.

Oxidation pathways towards Si amorphous layers or nanocrystalline powders as Li-ion batteries anodes

Silicon nanomaterials are obtained by an original approach based on the direct solution phase oxidation of a solid state Zintl phase NaSi used as silicon precursor. Alcohols with different alkyl chains are chosen as oxidizing agents. The materials are characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy and Raman spectroscopy. The most relevant parameter lies in the amorphous character of the silicon nanoparticles produced by this route. Amorphous nature of silicon is one of the key features for succeeding in the improvement of anodes for Li-ion batteries. The Si nanostructures have been tested as anodic materials for lithium ion batteries.