Grzegorz Trykowski

Self-Organized TiO2–MnO2 Nanotube Arrays for Efficient Photocatalytic Degradation of Toluene

Vertically oriented, self-organized TiO2–MnO2 nanotube arrays were successfully obtained by one-step anodic oxidation of Ti–Mn alloys in an ethylene glycol-based electrolyte. The as-prepared samples were characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), UV-Vis absorption, photoluminescence spectroscopy, X-ray diffraction (XRD), and micro-Raman spectroscopy. The effect of the applied potential (30–50 V), manganese content in the alloy (5–15 wt. %) and water content in the electrolyte (2–10 vol. %) on the morphology and photocatalytic properties was investigated for the first time. The photoactivity was assessed in the toluene removal reaction under visible light, using low-powered LEDs as an irradiation source (λmax = 465 nm). Morphology analysis showed that samples consisted of auto-aligned nanotubes over the surface of the alloy, their dimensions were: diameter = 76–118 nm, length = 1.0–3.4 μm and wall thickness = 8–11 nm. It was found that the increase in the applied potential led to increase the dimensions while the increase in the content of manganese in the alloy brought to shorter nanotubes. Notably, all samples were photoactive under the influence of visible light and the highest degradation achieved after 60 min of irradiation was 43%. The excitation mechanism of TiO2–MnO2 NTs under visible light was presented, pointing out the importance of MnO2 species for the generation of e− and h+.

Growth, Structure, and Photocatalytic Properties of Hierarchical V2O5–TiO2 Nanotube Arrays Obtained from the One-step Anodic Oxidation of Ti–V Alloys

V2O5-TiO2 mixed oxide nanotube (NT) layers were successfully prepared via the one-step anodization of Ti-V alloys. The obtained samples were characterized by scanning electron microscopy (SEM), UV-Vis absorption, photoluminescence spectroscopy, energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (DRX), and micro-Raman spectroscopy. The effect of the applied voltage (30–50 V), vanadium content (5–15 wt %) in the alloy, and water content (2–10 vol %) in an ethylene glycol-based electrolyte was studied systematically to determine their influence on the morphology, and for the first-time, on the photocatalytic properties of these nanomaterials. The morphology of the samples varied from sponge-like to highly-organized nanotubular structures. The vanadium content in the alloy was found to have the highest influence on the morphology and the sample with the lowest vanadium content (5 wt %) exhibited the best auto-alignment and self-organization (length = 1 μm, diameter = 86 nm and wall thickness = 11 nm). Additionally, a probable growth mechanism of V2O5-TiO2 nanotubes (NTs) over the Ti-V alloys was presented. Toluene, in the gas phase, was effectively removed through photodegradation under visible light (LEDs, λmax = 465 nm) in the presence of the modified TiO2 nanostructures. The highest degradation value was 35% after 60 min of irradiation. V2O5 species were ascribed as the main structures responsible for the generation of photoactive e− and h+ under Vis light and a possible excitation mechanism was proposed.

Effects of Ozone Dissolved in Water on the Physicochemical Properties of Activated Carbons Applied in Drinking Water Treatment

The results of treating commercial granulated activated carbons with ozone, both gaseous and dissolved in water, were analyzed. The original carbons (Filtrasorb-300 and Carbsorb-38) were carefully flushed with distilled water to remove any water-soluble impurities. For comparison, each of the washed activated carbons was treated separately with aqueous hydrogen peroxide. The following procedures were applied to assess the effects of contact between each carbon and the oxidizing agents: thermogravimetry, alkalimetry, voltammetry, EDX and FT-IR methods to illustrate changes in the surface chemistry, and nitrogen low-temperature adsorption to show up any possible changes in the porous structure. Ozone dissolved in water exhibited the lowest oxidative strength — EDX and FT-IR spectroscopy revealed only a slight oxidation of the Filtrasorb-300 surface layer. Despite its smaller specific area, this carbon surface exhibited greater roughness and was more susceptible to oxidation. The liquid-phase adsorption isotherms of p-chlorophenol from aqueous solution onto this carbon showed that surface oxygen reduced the extent of adsorption. The experimental data were best fitted by the Langmuir isotherm model.

Physical and chemical changes in Alhydrogel™ damaged by freezing

Accidental freezing of aluminum-based vaccines occurs during their storage and transportation, in both developed and developing countries. Freezing damages the freeze-sensitive aluminum adjuvanted vaccines, through separation of lattice between aluminum adjuvant and antigen, leading to formation of aluminum aggregates, and loss of potency. In this study, we examined Alhydrogel™ ([AlO(OH)]xnH2O, aluminum hydroxide, hydrated for adsorption) stored under recommended conditions, and exposed to freezing temperature until solid-frozen. The main purpose of our research was to determine the destruction areas of the solid-frozen Alhydrogel™ using selected methods of scanning electron microscopy, energy dispersive X-ray spectroscopy, Raman spectroscopy, Fourier-transform infrared spectroscopy and transmission electron microscopy working in diffraction mode. The Zeta potential evaluation, measurements of albumin adsorption power, thermogravimetric analysis and estimation of the mass loss after drying indicated significant structural (physical) and chemical differences between the freeze-damaged and non-frozen vaccine adjuvant. The presented results are important to better understand the type and nature of damages occurring in freeze-damaged aluminum-based vaccines. These results can be used in future studies to improve the temperature stability of aluminum adjuvanted vaccines.