Guan-Ting Pan

In situ DRIFT and kinetic studies of photocatalytic degradation on benzene vapor with visible-light-driven silver vanadates.

The visible-light active silver vanadates with different types of crystallines (Ag(4)V(2)O(7) and Ag(3)VO(4) phases) were synthesized by an environmentally friendly aqueous process. The parameters of hydrothermal temperature and hydrothermal time were tuned to maximize the photocatalytic efficiency for the decomposition of benzene vapor under visible-light irradiation. The quantum efficiencies of the photocatalysts are compared on the basis of the crystalline phases, surface area, intensity of surface hydroxyl groups, and Brönsted acid sites. From the results of DRIFTS studies, the photocatalytic activities strongly depend on the intensities of the Brönsted acidity and hydroxyl groups presented on the silver vanadates. The sample synthesized at 140 degrees C and 4h (HM140) exhibits the best photocatalytic activity; it has a reaction rate constant (k(app)) of 1.42 min(-1), much higher than that of P25 (k(app)=0.13 min(-1)). For an irradiation time of 720 min, the mineralization yields of benzene were 48% and 11% for HM140 and P25, respectively. Based on the short-term decrease of benzene concentration and the long-term increase of CO(2) concentration, the photocatalytic ability of the HM140 sample is significantly superior to that of P25. The highest activity can be attributed to the synergetic effects of the richest Brönsted acid sites, and a favorable crystalline phase combined with abundant surface hydroxyl groups.

Physical Characterization and Pre-assessment of Recycled High-Density Polyethylene as 3D Printing Material

Abstract3D printing has received lots of attention due to its limitless potential and advantages in comparison to traditional manufacturing processes. This study focuses on the most popular type of home 3D printers, namely fused filament fabrication (FFF) printers, which use plastic filaments as the feedstock. The rather high material cost and large amount of plastic waste generated by FFF 3D printers have driven the need for plastic filaments produced from recycled plastic waste. This study evaluates, in terms of physical characterization, the feasibility of using recycled high-density polyethylene (HDPE), one of the most commonly used plastics, as the feedstock for 3D printers, in comparison with the common acrylonitrile butadiene styrene plastic pellets. In-house extrusion using recycled HDPE pellets and flakes is possible. The diameter consistency and extrusion rate results, along with other physical characterization results, including differential scanning calorimetry, thermogravimetric analysis, Fourier transform infrared spectroscopy, Raman spectroscopy, and water absorption, suggest that making filaments from recycled HDPE pellets is a viable option, as the obtained filament has favorable water rejection and comparable extrusion rate and thermal stability. Existing methods for overcoming the warping and adhesion problems in 3D printing with HDPE were also reviewed. In order to increase the market competitiveness of waste-derived filaments, optimization of the extrusion process, studies on the mechanical and aging properties, and development of a standard characterization methodology and database are crucial.

Surface Modification of Amorphous SiO2 Nanoparticles by Oxygen-Plasma and Nitrogen-Plasma Treatments

In this study, amorphous silica gels were synthesized and treated by oxygen plasma and nitrogen plasma at a radio frequency power of 60 W, at heating temperature of 300°C, and a treatment period of 400 s. The silica gels were characterized by using X-ray diffraction, Fourier-transform infrared spectroscopy, scanning electron microscopy, Brunauer–Emmett–Teller, and thermal conductivity analyzers. The characterization results show that oxygen-plasma treatment has remarkably reduced the surface hydroxyl groups in silica gels, whereas nitrogen-plasma treatment has less effects. The reduction of the hydroxyl groups is a key factor contributing to reduced particle size from 30 nm to 15 nm, thus resulting in an increased specific surface area from 124 to 420 m2/g. In addition, the reduced particle size has drastically lowered the thermal conductivity of silica gels, from 0.14220 to 0.00014 W/mK. Therefore, oxygen-plasma treatment is a feasible method to enhance the thermal insulating properties of silica gels.

The Preparation of Porous Sol-Gel Silica with Metal Organic Framework MIL-101(Cr) by Microwave-Assisted Hydrothermal Method for Adsorption Chillers

Metal organic framework (MOF) of MIL-101(Cr)-Silica (SiO2) composites with highly mesoporous and uniform dispersions were synthesized by a microwave-assisted hydrothermal method followed by the sol-gel technique. Water vapor adsorption experiments were conducted on the MIL-101(Cr)-SiO2 composites for industrial adsorption chiller applications. The effects of MIL-101(Cr)-SiO2 mixing ratios (ranging from 0% to 52%), the surface area and amount of Lewis and Brønsted sites were comprehensively determined through water vapor adsorption experiments and the adsorption mechanism is also explained. The BET and Langmuir results indicate that the adsorption isotherms associated with the various MIL-101(Cr)-SiO2 ratios demonstrated Type I and IV adsorption behavior, due to the mesoporous structure of the MIL-101(Cr)-SiO2. It was observed that the increase in the amount of Lewis and Brønsted sites on the MIL-101(Cr)-SiO2 composites significantly improves the water vapor adsorption efficiency, for greater stability during the water vapor adsorption experiments.

Electrodeposited Porous Mn1.5Co1.5O4/Ni Composite Electrodes for High-Voltage Asymmetric Supercapacitors

Mesoporous Mn1.5Co1.5O4 (MCO) spinel films were prepared directly on a conductive nickel (Ni) foam substrate via electrodeposition and an annealing treatment as supercapacitor electrodes. The electrodeposition time markedly influenced the surface morphological, textural, and supercapacitive properties of MCO/Ni electrodes. The (MCO/Ni)-15 min electrode (electrodeposition time: 15 min) exhibited the highest capacitance among three electrodes (electrodeposition times of 7.5, 15, and 30 min, respectively). Further, an asymmetric supercapacitor that utilizes (MCO/Ni)-15 min as a positive electrode, a plasma-treated activated carbon (PAC)/Ni electrode as a negative electrode, and carboxymethyl cellulose-lithium nitrate (LiNO3) gel electrolyte (denoted as (PAC/Ni)//(MCO/Ni)-15 min) was fabricated. In a stable operation window of 2.0 V, the device exhibited an energy density of 27.6 Wh·kg−1 and a power density of 1.01 kW·kg−1 at 1 A·g−1. After 5000 cycles, the specific energy density retention and power density retention were 96% and 92%, respectively, demonstrating exceptional cycling stability. The good supercapacitive performance and excellent stability of the (PAC/Ni)//(MCO/Ni)-15 min device can be ascribed to the hierarchical structure and high surface area of the (MCO/Ni)-15 min electrode, which facilitate lithium ion intercalation and deintercalation at the electrode/electrolyte interface and mitigate volume change during long-term charge/discharge cycling.

The production of an efficient visible light photocatalyst for CO oxidation through the surface plasmonic effect of Ag nanoparticles on SiO2@α-Fe2O3 nanocomposites

A process for the photo deposition of noble Ag nanoparticles on a core–shell structure of SiO2@α-Fe2O3 nanocomposite spheres was performed to produce a CO photo oxidation catalyst. The structural analyses were carried out for samples produced using different Ag metal nanoparticle weight percentages on SiO2@α-Fe2O3 nanocomposite spheres by X-ray diffraction (XRD), field emission-scanning electron microscopy (FE-SEM), UV-vis spectroscopy, Raman spectroscopy and Fourier transform infrared spectroscopy (FTIR). A computational study was also performed to confirm the existence of the synergic effect of surface plasmon resonance (SPR) for different weight percentages of Ag on the SiO2@α-Fe2O3 nanocomposites. The mechanism for CO oxidation on the catalyst was explored using diffuse reflectance infrared Fourier transform spectroscopy (DRFIT). The CO oxidation results for the Ag (2 wt%)-SiO2@α-Fe2O3 nanocomposite spheres showed 48% higher photocatalytic activity than α-Fe2O3 and SiO2@α-Fe2O3 at stable temperature.

Degradation of Methylene Blue Dye in the Presence of Visible Light Using SiO2@α-Fe2O3 Nanocomposites Deposited on SnS2 Flowers

Semiconductor materials have been shown to have good photocatalytic behavior and can be utilized for the photodegradation of organic pollutants. In this work, three-dimensional flower-like SnS2 (tin sulfide) was synthesized by a facile hydrothermal method. Core-shell structured SiO2@α-Fe2O3 nanocomposites were then deposited on the top of the SnS2 flowers. The as-synthesized nanocomposites were characterized by X-ray diffraction (XRD), Raman spectroscopy, field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), UV–Vis Spectroscopy, Brunauer–Emmett–Teller (BET) surface area analysis, and photoluminescence (PL) spectroscopy. The photocatalytic behavior of the SnS2-SiO2@α-Fe2O3 nanocomposites was investigated by observing the degradation of methylene blue (MB). The results show an effective enhancement of photocatalytic activity for the degradation of MB especially for the 15 wt % SiO2@α-Fe2O3 nanocomposites on SnS2 flowers.

Adsorptive decontamination of diclofenac by three-dimensional graphene-based adsorbent: Response surface methodology, adsorption equilibrium, kinetic and thermodynamic studies

&NA; Pharmaceutical residues are emerging pollutants in the aquatic environment and their removal by conventional wastewater treatment methods has proven to be ineffective. This research aimed to develop a three‐dimensional reduced graphene oxide aerogel (rGOA) for the removal of diclofenac in aqueous solution. The preparation of rGOA involved facile self‐assembly of graphene oxide under a reductive environment of L‐ascorbic acid. Characterisation of rGOA was performed by Fourier transform infrared, scanning electron microscope, transmission electron microscopy, nitrogen adsorption‐desorption, Raman spectroscopy and X‐ray diffraction. The developed rGOA had a measured density of 20.39 ± 5.28 mg/cm3, specific surface area of 132.19 m2/g, cumulative pore volume of 0.5388 cm3/g and point of zero charge of 6.3. A study on the simultaneous interactions of independent factors by response surface methodology suggested dosage and initial concentration as the dominant parameters influencing the adsorption of diclofenac. The highest diclofenac adsorption capacity (596.71 mg/g) was achieved at the optimum conditions of 0.25 g/L dosage, 325 mg/L initial concentration, 200 rpm shaking speed and 30 °C temperature. The adsorption equilibrium data were best fitted to the Freundlich model with correlation coefficient (R2) varying from 0.9500 to 0.9802. The adsorption kinetic data were best correlated to the pseudo‐first‐order model with R2 ranging from 0.8467 to 0.9621. Thermodynamic analysis showed that the process was spontaneous (&Dgr;G = − 7.19 to − 0.48 kJ/mol) and exothermic (&Dgr;H = − 12.82 to − 2.17 kJ/mol). This research concluded that rGOA is a very promising adsorbent for the remediation of water polluted by diclofenac.