Guangming Tao

Structured spheres generated by an in-fibre fluid instability

From drug delivery to chemical and biological catalysis and cosmetics, the need for efficient fabrication pathways for particles over a wide range of sizes, from a variety of materials, and in many different structures has been well established. Here we harness the inherent scalability of fibre production and an in-fibre Plateau–Rayleigh capillary instability for the fabrication of uniformly sized, structured spherical particles spanning an exceptionally wide range of sizes: from 2 mm down to 20 nm. Thermal processing of a multimaterial fibre controllably induces the instability, resulting in a well-ordered, oriented emulsion in three dimensions. The fibre core and cladding correspond to the dispersed and continuous phases, respectively, and are both frozen in situ on cooling, after which the particles are released when needed. By arranging a variety of structures and materials in a macroscopic scaled-up model of the fibre, we produce composite, structured, spherical particles, such as core–shell particles, two-compartment ‘Janus’ particles, and multi-sectioned ‘beach ball’ particles. Moreover, producing fibres with a high density of cores allows for an unprecedented level of parallelization. In principle, 108 50-nm cores may be embedded in metres-long, 1-mm-diameter fibre, which can be induced to break up simultaneously throughout its length, into uniformly sized, structured spheres.

Multimaterial preform coextrusion for robust chalcogenide optical fibers and tapers.

The development of robust infrared fibers is crucial for harnessing the capabilities of new mid-infrared lasers. We present a novel approach to the fabrication of chalcogenide glass fiber preforms: one-step multimaterial extrusion. The preform consists of a glass core and cladding surrounded by a built-in, thermally compatible, polymer jacket for mechanical support. Using this approach we extrude several preform structures and draw them into robust composite fibers. Furthermore, the polymer cladding allows us to produce robust tapers with submicrometer core diameter.

Thermal drawing of high-density macroscopic arrays of well-ordered sub-5-nm-diameter nanowires.

We investigate the lower limit of nanowire diameters stably produced by the process of thermal fiber drawing and fiber tapering. A centimeter-scale macroscopic cylindrical preform containing the nanowire material in the core encased in a polymer scaffold cladding is thermally drawn in the viscous state to a fiber. By cascading several iterations of the process, continuous reduction of the diameter of an amorphous semiconducting chalcogenide glass is demonstrated. Starting from a 10-mm-diameter rod we thermally draw hundreds of meters of continuous sub-5-nm-diameter nanowires. Using this approach, we produce macroscopic lengths of high-density, well-ordered, globally oriented nanowire arrays.

Robust multimaterial tellurium-based chalcogenide glass fibers for mid-wave and long-wave infrared transmission

We describe an approach for producing robust multimaterial chalcogenide glass fibers for mid-wave and long-wave mid-infrared transmission. By combining the traditional rod-in-tube process with multimaterial coextrusion, we prepare a hybrid glass-polymer preform that is drawn continuously into a robust step-index fiber with a built-in, thermally compatible polymer jacket. Using tellurium-based chalcogenides, the fibers have a transparency window covering the 3-12 μm spectral range, making them particularly attractive for delivering quantum cascade laser light and in space applications.

Controlled fragmentation of multimaterial fibres and films via polymer cold-drawing

Polymer cold-drawing is a process in which tensile stress reduces the diameter of a drawn fibre (or thickness of a drawn film) and orients the polymeric chains. Cold-drawing has long been used in industrial applications, including the production of flexible fibres with high tensile strength such as polyester and nylon. However, cold-drawing of a composite structure has been less studied. Here we show that in a multimaterial fibre composed of a brittle core embedded in a ductile polymer cladding, cold-drawing results in a surprising phenomenon: controllable and sequential fragmentation of the core to produce uniformly sized rods along metres of fibre, rather than the expected random or chaotic fragmentation. These embedded structures arise from mechanical–geometric instabilities associated with ‘neck’ propagation. Embedded, structured multimaterial threads with complex transverse geometry are thus fragmented into a periodic train of rods held stationary in the polymer cladding. These rods can then be easily extracted via selective dissolution of the cladding, or can self-heal by thermal restoration to re-form the brittle thread. Our method is also applicable to composites with flat rather than cylindrical geometries, in which case cold-drawing leads to the break-up of an embedded or coated brittle film into narrow parallel strips that are aligned normally to the drawing axis. A range of materials was explored to establish the universality of this effect, including silicon, germanium, gold, glasses, silk, polystyrene, biodegradable polymers and ice. We observe, and verify through nonlinear finite-element simulations, a linear relationship between the smallest transverse scale and the longitudinal break-up period. These results may lead to the development of dynamical and thermoreversible camouflaging via a nanoscale Venetian-blind effect, and the fabrication of large-area structured surfaces that facilitate high-sensitivity bio-detection.

Fabrication and characterization of multimaterial chalcogenide glass fiber tapers with high numerical apertures

This paper reports on the fabrication and characterization of multimaterial chalcogenide fiber tapers that have high numerical apertures (NAs). We first fabricated multimaterial As(2)Se(3)-As(2)S(3) chalcogenide fiber preforms via a modified one-step coextrusion process. The preforms were drawn into multi- and single-mode fibers with high NAs (≈1.45), whose core/cladding diameters were 103/207 and 11/246 μm, respectively. The outer diameter of the fiber was tapered from a few hundred microns to approximately two microns through a self-developed automatic tapering process. Simulation results showed that the zero-dispersion wavelengths (ZDWs) of the tapers were shorter than 2 μm, indicating that the tapers can be conveniently pumped by commercial short wavelength infrared lasers. We also experimentally demonstrated the supercontinuum generation (SCG) in a 15-cm-long multimaterial As(2)Se(3)-As(2)S(3) chalcogenide taper with 1.9 μm core diameter and the ZDW was shifted to 3.3 μm. When pumping the taper with 100 fs short pulses at 3.4 µm, a 20 dB spectral of the generated supercontinuum spans from 1.5 μm to longer than 4.8 μm.

In-fiber production of polymeric particles for biosensing and encapsulation

Significance A scalable, chemistry-independent, fluid-instability–mediated in-fiber route for fabricating uniformly sized spherical polymeric particles over a wide span of diameters is developed targeting biomedical applications. Both surface functionalization of solid biocompatible polymer particles for protein–protein interactions and volume encapsulation of a biological material in spherical hollow polymer shells are confirmed, in addition to combining both surface and volumetric functionalities in the same polymeric particle. Polymeric micro- and nanoparticles are becoming a mainstay in biomedicine, medical diagnostics, and therapeutics, where they are used in implementing sensing mechanisms, as imaging contrast agents, and in drug delivery. Current approaches to the fabrication of such particles are typically finely tuned to specific monomer or polymer species, size ranges, and structures. We present a general scalable methodology for fabricating uniformly sized spherical polymeric particles from a wide range of polymers produced with complex internal architectures and continuously tunable diameters extending from the millimeter scale down to 50 nm. Controllable access to such a wide range of sizes enables broad applications in cancer treatment, immunology, and vaccines. Our approach harnesses thermally induced, predictable fluid instabilities in composite core/cladding polymer fibers drawn from a macroscopic scaled-up model called a “preform.” Through a stack-and-draw process, we produce fibers containing a multiplicity of identical cylindrical cores made of the polymers of choice embedded in a polymer cladding. The instability leads to the breakup of the initially intact cores, independent of the polymer chemistry, into necklaces of spherical particles held in isolation within the cladding matrix along the entire fiber length. We demonstrate here surface functionalization of the extracted particles for biodetection through specific protein–protein interactions, volumetric encapsulation of a biomaterial in spherical polymeric shells, and the combination of both surface and volumetric functionalities in the same particle. These particles used in distinct modalities may be produced from the desired biocompatible polymer by changing only the geometry of the macroscopic preform from which the fiber is drawn.

Dispersion characterization of chalcogenide bulk glass, composite fibers, and robust nanotapers

We report the results of systematic measurements of the group velocity dispersion (GVD) in chalcogenide glass (ChG) bulk samples, composite ChG fibers, and robust high-index-contrast nanotapers. The composite ChG-polymer fibers are drawn from an extruded multimaterial preform incorporating a thick built-in polymer jacket that is thermally compatible with the ChG used, and the nanotapers are then produced without removing the polymer. We isolate the contributions of material and waveguide GVD to the total dispersion in the nanotapers and support the results with finite-element simulations. These results indicate many possibilities for dispersion engineering and nonlinearity enhancement in all-solid index-guiding ChG fibers stemming from the flexibility of this fiber fabrication methodology.

High-resolution chalcogenide fiber bundles for infrared imaging

An ordered chalcogenide fiber bundle with a high resolution for infrared imaging was fabricated using a stack-and-draw approach. The fiber bundle consisted of about 810,000 single fibers with an As2S3 glass core of 9 μm in diameter and a polyetherimide (PEI) polymer cladding of 10 μm in diameter. The As2S3/PEI fibers showed good transparency in the 1.5-6.5 μm spectral region. It presented a resolution of ∼45  lp/mm and a crosstalk of ∼2.5%. Fine thermal images of a hot soldering iron tip were delivered through the fiber bundle.

Multimaterial disc-to-fiber approach to efficiently produce robust infrared fibers

A critical challenge in the fabrication of chalcogenide-glass infrared optical fibers is the need for first producing large volumes of high-purity glass – a formidable task, particularly in the case of multicomponent glasses. We describe here a procedure based on multimaterial coextrusion of a hybrid glass-polymer preform from which extended lengths of robust infrared fibers are readily drawn. Only ~2 g of glass is required to produce 46 m of step-index fiber with core diameters in the range 10 – 18 μm. This process enables rapid prototyping of a variety of glasses for applications in the delivery of quantum cascade laser light, spectroscopy, sensing, and astronomy.