H. Armandula

Titania-doped tantala/silica coatings for gravitational-wave detection

Reducing thermal noise from optical coatings is crucial to reaching the required sensitivity in next generation interferometric gravitational-wave detectors. Here we show that adding TiO2 to Ta2O5 in Ta2O5/SiO2 coatings reduces the internal friction and in addition present data confirming it reduces thermal noise. We also show that TiO2-doped Ta2O5/SiO2 coatings are close to satisfying the optical absorption requirements of second generation gravitational-wave detectors.

Mechanical loss in tantala/silica dielectric mirror coatings

Current interferometric gravitational wave detectors use test masses with mirror coatings formed from multiple layers of dielectric materials, most commonly alternating layers of SiO2 (silica) and Ta2O5 (tantala). However, mechanical loss in the Ta2O5/SiO2 coatings may limit the design sensitivity for advanced detectors. We have investigated sources of mechanical loss in the Ta2O5/SiO2 coatings, including loss associated with the coating–substrate interface, with the coating–layer interfaces and with the coating materials. Our results indicate that the loss is associated with the coating materials and that the loss of Ta2O5 is substantially larger than that of SiO2.

Search for gravitational-wave bursts associated with gamma-ray bursts using data from LIGO science run 5 and VIRGO science run 1.

We present the results of a search for gravitational-wave bursts associated with 137 gamma-ray bursts (GRBs) that were detected by satellite-based gamma-ray experiments during the fifth LIGO science run and first Virgo science run. The data used in this analysis were collected from 2005 November 4 to 2007 October 1, and most of the GRB triggers were from the Swift satellite. The search uses a coherent network analysis method that takes into account the different locations and orientations of the interferometers at the three LIGO-Virgo sites. We find no evidence for gravitational-wave burst signals associated with this sample of GRBs. Using simulated short-duration (<1 s) waveforms, we set upper limits on the amplitude of gravitational waves associated with each GRB. We also place lower bounds on the distance to each GRB under the assumption of a fixed energy emission in gravitational waves, with typical limits of D ~ 15 Mpc (E_GW^iso / 0.01 M_o c^2)^1/2 for emission at frequencies around 150 Hz, where the LIGO-Virgo detector network has best sensitivity. We present astrophysical interpretations and implications of these results, and prospects for corresponding searches during future LIGO-Virgo runs.

Thermal noise from optical coatings in gravitational wave detectors.

Gravitational waves are a prediction of Einsteins general theory of relativity. These waves are created by massive objects, like neutron stars or black holes, oscillating at speeds appreciable to the speed of light. The detectable effect on the Earth of these waves is extremely small, however, creating strains of the order of 10(-21). There are a number of basic physics experiments around the world designed to detect these waves by using interferometers with very long arms, up to 4 km in length. The next-generation interferometers are currently being designed, and the thermal noise in the mirrors will set the sensitivity over much of the usable bandwidth. Thermal noise arising from mechanical loss in the optical coatings put on the mirrors will be a significant source of noise. Achieving higher sensitivity through lower mechanical loss coatings, while preserving the crucial optical and thermal properties, is an area of active research right now.

Measurements of a low-temperature mechanical dissipation peak in a single layer of Ta2O5 doped with TiO2

Thermal noise arising from mechanical dissipation in oxide coatings is a major limitation to many precision measurement systems, including optical frequency standards, high-resolution optical spectroscopy and interferometric gravity wave detectors. Presented here are measurements of dissipation as a function of temperature between 7 K and 290 K in ion-beam-sputtered Ta2O5 doped with TiO2, showing a loss peak at 20 K. Analysis of the peak provides the first evidence of the source of dissipation in doped Ta2O5 coatings, leading to possibilities for the reduction of thermal noise effects.

Comparison of the temperature dependence of the mechanical dissipation in thin films of Ta2O5 and Ta2O5 doped with TiO2

Here we report the first results comparing the temperature dependence of the mechanical dissipation in thin films of Ta_2O_5 and Ta_2O_5 doped with TiO_2, of a type suitable for use in the multilayer optical coatings for advanced gravitational wave detectors. The results indicate that doping Ta_2O_5 with TiO_2 can significantly alter the distribution of activation energies associated with the low-temperature dissipation peak.

Low mechanical loss coatings for LIGO optics: progress report

A significant limiting factor on the sensitivity of interferometric gravitational wave detectors has been identified as thermal noise generated by mechanical loss in the high reflectivity dielectric mirror coatings on the test masses. The development of coatings which maintain high optical performance and minimize mechanical loss is therefore vital if the current designs of interferometers are to achieve adequate sensitivity. While the origins of the mechanical loss are yet to be fully elucidated, some progress has been made toward minimizing it, although there is still some way to go before specifications can be met. The work reported here is progress made toward achieving low mechanical loss coatings on behalf of the LIGO consortium. The current directions include attempts to reduce the loss in the coating materials by control of the coating stoichiometry and intrinsic stress. This includes such methods as ion bombardment of the growing films and optimization of post-deposition thermal treatments.

Optical coatings for gravitational-wave detection

Einsteins General Theory of Relativity predicts waves in spacetime caused by oscillating masses. Such waves, known as gravitational waves, are predicted to be created by binary black hole or neutron star inspirals, super-nova, or other catastrophic astronomical events. Even with such large masses moving so repidly, the expected size of the waves is extremely small, typically of order 10-21 in unitless strain as seen on Earth. LIGO, the Laser Interferometer Gravitational Wave Observatory, is a basic physics experiments designed to detect and study these waves. The next generation interferometers, known as Advanced LIGO, are currently being designed. Thermal noise from mechanical loss in the optical coatings of the mirrors is expected to be an important limiting noise source. Reducing this noise by developing lower mechanical loss coatings, while preserving optical and thermal properties needed in the interferometer, is an area of active research.

Silica suspension and coating developments for Advanced LIGO

The proposed upgrade to the LIGO detectors to form the Advanced LIGO detector system is intended to incorporate a low thermal noise monolithic fused silica final stage test mass suspension based on developments of the GEO 600 suspension design. This will include fused silica suspension elements jointed to fused silica test mass substrates, to which dielectric mirror coatings are applied. The silica fibres used for GEO 600 were pulled using a Hydrogen-Oxygen flame system. This successful system has some limitations, however, that needed to be overcome for the more demanding suspensions required for Advanced LIGO. To this end a fibre pulling machine based on a CO2 laser as the heating element is being developed in Glasgow with funding from EGO and PPARC. At the moment a significant limitation for proposed detectors like Advanced LIGO is expected to come from the thermal noise of the mirror coatings. An investigation on mechanical losses of silica/tantala coatings was carried out by several labs involved with Advanced LIGO R&D. Doping the tantala coating layer with titania was found to reduce the coating mechanical dissipation. A review of the results is given here.

Optical coatings for gravitational wave detection

Gravitational waves are a prediction of Einsteins General Theory of Relativity. Astrophysical events like supernova and binary neutron star inspirals are predicted to create potentially detectable waves. The Laser Interferometer Gravitational-wave Observatory (LIGO) is an experiment to detect these waves using Michelson interferometers with 4 km long arms. The effect of gravitational waves, even on an interferometer with such a long baseline, is extremely, with mirror displacements around 10-18m. Reducing noise is thus a primary design criterion. For the next generation interferometers now being designed, thermal noise from the optical coatings of the interferometer mirrors could prove a problematic limiting noise source. Reducing the mechanical loss of these coatings to improve thermal noise, while preserving the sub-ppm optical absorption, low scatter, and high reflectivity needed in the interferometer is an important area of research.