Haiyun Xia

Mid-altitude wind measurements with mobile Rayleigh Doppler lidar incorporating system-level optical frequency control method

A mobile Rayleigh Doppler lidar based on double-edge technique is developed for mid-altitude wind observation. To reduce the systematic error, a system-level optical frequency control method is proposed and demonstrated. The emission of the seed laser at 1064 nm is used to synchronize the FPI in the optical frequency domain. A servo loop stabilizing the frequency of the seed laser is formed by measuring the absolute frequency of the second harmonic against an iodine absorption line. And, the third harmonic is used for Rayleigh lidar detection. The frequency stability is 1.6 MHz at 1064 nm over 2 minutes. A locking accuracy of 0.3 MHz at 1064 nm is realized. In comparison experiments, wind profiles from the lidar, radiosonde and European Center for Medium range Weather Forecast (ECMWF) analysis show good agreement from 8 km to 25 km. Wind observation over two months is carried out in Urumqi (42.1°N, 87.1°E), northwest of China, demonstrating the stability and robustness of the system. For the first time, quasi-zero wind layer and dynamic evolution of high-altitude tropospheric jet are observed based on Rayleigh Doppler lidar in Asia.

Long-range micro-pulse aerosol lidar at 1.5 μm with an upconversion single-photon detector

A micro-pulse lidar at eye-safe wavelength is constructed based on an upconversion single-photon detector. The ultralow-noise detector enables using integration technique to improve the signal-to-noise ratio of the atmospheric backscattering even at daytime. With pulse energy of 110 μJ, pulse repetition rate of 15 kHz, optical antenna diameter of 100 mm and integration time of 5 min, a horizontal detection range of 7 km is realized. In the demonstration experiment, atmospheric visibility over 24 h is monitored continuously, with results in accordance with the weather forecasts.

Mobile Rayleigh Doppler lidar for wind and temperature measurements in the stratosphere and lower mesosphere

A mobile Rayleigh Doppler lidar based on the molecular double-edge technique is developed for measuring wind velocity in the middle atmosphere up to 60 km. The lidar uses three lasers with a mean power of 17.5 W at 355 nm each and three 1 m diameter telescopes to receive the backscattered echo: one points to zenith for vertical wind component and temperature measurement; the two others pointing toward east and north are titled at 30° from the zenith for zonal and meridional wind component, respectively. The Doppler shift of the backscattered echo is measured by inter-comparing the signal detected through each of the double-edge channels of a triple Fabry-Perot interferometer (FPI) tuned to either side of the emitted laser line. The third channel of FPI is used for frequency locking and a locking accuracy of 1.8 MHz RMS (root-mean-square) at 355 nm over 2 hours is realized, corresponding to a systematic error of 0.32 m/s. In this paper, we present detailed technical evolutions on system calibration. To validate the performance of the lidar, comparison experiments was carried out in December 2013, which showed good agreement with radiosondes but notable biases with ECMWF (European Centre for Medium range Weather Forecasts) in the height range of overlapping data. Wind observation over one month performed in Delhi (37.371° N, 97.374° E), northwest of China, demonstrated the stability and robustness of the system.

All-fiber upconversion high spectral resolution wind lidar using a Fabry-Perot interferometer

An all-fiber, micro-pulse and eye-safe high spectral resolution wind lidar (HSRWL) at 1.5 μm is proposed and demonstrated by using a pair of upconversion single-photon detectors and a fiber Fabry-Perot scanning interferometer (FFP-SI). In order to improve the optical detection efficiency, both the transmission spectrum and the reflection spectrum of the FFP-SI are used for spectral analyses of the aerosol backscatter and the reference laser pulse. Taking advantages of high signal-to-noise ratio of the detectors and high spectral resolution of the FFP-SI, the center frequencies and the bandwidths of spectra of the aerosol backscatter are obtained simultaneously. Continuous LOS wind observations are carried out on two days at Hefei (31.843 °N, 117.265 °E), China. The horizontal detection range of 4 km is realized with temporal resolution of 1 minute. The spatial resolution is switched from 30 m to 60 m at distance of 1.8 km. In a comparison experiment, LOS wind measurements from the HSRWL show good agreement with the results from an ultrasonic wind sensor (Vaisala windcap WMT52). An empirical method is adopted to evaluate the precision of the measurements. The standard deviation of the wind speed is 0.76 m/s at 1.8 km. The standard deviation of bandwidth variation is 2.07 MHz at 1.8 km.

Micro-pulse upconversion Doppler lidar for wind and visibility detection in the atmospheric boundary layer.

For the first time, to the best of our knowledge, a compact, eye-safe, and versatile direct detection Doppler lidar is developed using an upconversion single-photon detection method at 1.5 μm. An all-fiber and polarization maintaining architecture is realized to guarantee the high optical coupling efficiency and the robust stability. Using integrated-optic components, the conservation of etendue of the optical receiver is achieved by manufacturing a fiber-coupled periodically poled lithium niobate waveguide and an all-fiber Fabry-Perot interferometer (FPI). The double-edge technique is implemented by using a convert single-channel FPI and a single upconversion detector, incorporating a time-division multiplexing method. The backscatter photons at 1548.1 nm are converted into 863 nm via mixing with a pump laser at 1950 nm. The relative error of the system is less than 0.1% over nine weeks. In experiments, atmospheric wind and visibility over 48 h are detected in the boundary layer. The lidar shows good agreement with the ultrasonic wind sensor, with a standard deviation of 1.04 m/s in speed and 12.3° in direction.

Stratospheric temperature measurement with scanning Fabry-Perot interferometer for wind retrieval from mobile Rayleigh Doppler lidar

Temperature detection remains challenging in the low stratosphere, where the Rayleigh integration lidar is perturbed by aerosol contamination and ozone absorption while the rotational Raman lidar is suffered from its low scattering cross section. To correct the impacts of temperature on the Rayleigh Doppler lidar, a high spectral resolution lidar (HSRL) based on cavity scanning Fabry-Perot Interferometer (FPI) is developed. By considering the effect of the laser spectral width, Doppler broadening of the molecular backscatter, divergence of the light beam and mirror defects of the FPI, a well-behaved transmission function is proved to show the principle of HSRL in detail. Analysis of the statistical error of the HSRL is carried out in the data processing. A temperature lidar using both HSRL and Rayleigh integration techniques is incorporated into the Rayleigh Doppler wind lidar. Simultaneous wind and temperature detection is carried out based on the combined system at Delhi (37.371°N, 97.374°E; 2850 m above the sea level) in Qinghai province, China. Lower Stratosphere temperature has been measured using HSRL between 18 and 50 km with temporal resolution of 2000 seconds. The statistical error of the derived temperatures is between 0.2 and 9.2 K. The temperature profile retrieved from the HSRL and wind profile from the Rayleigh Doppler lidar show good agreement with the radiosonde data. Specifically, the max temperature deviation between the HSRL and radiosonde is 4.7 K from 18 km to 36 km, and it is 2.7 K between the HSRL and Rayleigh integration lidar from 27 km to 34 km.

Low Stratospheric Wind Measurement Using Mobile Rayleigh Doppler Wind LIDAR

A mobile Rayleigh Doppler wind LIDAR at an eye-safe wavelength of 355 nm incorporating double-edge technique with triple-channel Fabry-Perot etalon is developed for wind measurement from 5 to 40km. The structure of this LIDAR system is described. An intercomparsion experiment with rawinsonde is made, showing good agreement with expected measurement accuracy. A continuous observation of stratosphere wind field for several days with temporal resolution of 15 min and spatial resolution of 200 m from 5 to 40 km is presented, demonstrating the stability and robustness of the LIDAR. A stratospheric quasi-zero wind layer can be found at around 20 km with a direction change from east to west evident in the continuous observation.

Brillouin optical time-domain reflectometry using up-conversion single-photon detector

A direct-detection Brillouin optical time-domain reflectometry (BOTDR) is proposed and demonstrated by using an up-conversion single-photon detector and a fiber Fabry-Perot scanning interferometer (FFP-SI). Taking advantage of high signal-to-noise ratio of the detector and high spectrum resolution of the FFP-SI, the Brillouin spectrum along a polarization maintaining fiber (PMF) is recorded on a multiscaler with a small data size directly. In contrast with conventional BOTDR adopting coherent detection, photon-counting BOTDR is simpler in structure and easier in data processing. In the demonstration experiment, characteristic parameters of the Brillouin spectrum including its power, spectral width and frequency center are analyzed simultaneously along a 10 km PMF at different temperature and stain conditions.

15 μm polarization coherent lidar incorporating time-division multiplexing

Atmospheric depolarization ratio and wind velocity are measured simultaneously by a single versatile coherent Doppler lidar (CDL). Backscattering components at parallel and perpendicular polarization states are obtained by using a single balanced detector, adopting time-division multiplexing technique. Thus systematic error induced by the non-uniform response of different detectors in traditional lidars is avoided. The operation mode of the instrument can be switched from polarization CDL to traditional CDL by the user depending on atmospheric conditions and desired performance. As demonstrated, the perpendicular component of the backscattering, usually wasted, not only can be used to retrieve the ADR, but also can be used to improve the carrier to noise ratio in wind detection. In the traditional mode, given a tolerance of 0.5 m/s precision, a detection range of 6 km is achieved by using a 300 ns laser pulse with energy of 100 μJ, where the temporal and spatial resolution of 2 s and 60 m, respectively. Continuous wind detection of the atmospheric boundary layer over 26 hours is presented to demonstrate the robustness and stability of the system. Dynamic evolution and wind structure are recorded.

Analysis on wind retrieval methods for Rayleigh Doppler lidar

Abstract. A modification method is described for Rayleigh Doppler lidar wind retrieval. Compared to the double-edge theory of Korb et al. [Appl. Opt. 38, 432 (1999)] and the retrieval algorithm of Chanin et al. [Geophys. Res. Lett. 16, 1273 (1989)], it has a greater sensitivity. The signal-to-noise ratio of the energy monitor channel is involved in error estimation. When the splitting ratio of the two signal channels is 1.2, which usually happened during wind detection, it will improve the measurement accuracy by about 1% at 30 km altitude for a Doppler shift of 250 MHz (44  m/s). Stabilities of retrieval methods, i.e., errors caused by the spectrum width deviation including laser pulse, Rayleigh backscatter, and filter transmission curve are first discussed. The proposed method increases the resultant precision by about 15% at 30-km altitude assuming an 8-MHz deviation in full width at half maximum of the Fabry–Perot interferometer.