Han-Jung Kim

A cupronickel-based micromesh film for use as a high-performance and low-voltage transparent heater

The fabrication of uniformly interconnected cupronickel (CuNi) micromesh films on glass and polymer substrates with seamless junctions has been achieved using a simple transfer printing method. When used as a transparent heater, these CuNi micromesh films exhibited an effective and rapid heating performance at low input voltages (below DC 9 V) that can be attributed to the creation of a high quality network over the whole surface area that offers a relatively high transmittance, strong adhesion to its substrate and good mechanical flexibility. A high thermal stability and reliability was also observed relative to a pure Cu micromesh film. Transparent heaters based on CuNi micromesh are therefore considered suitable for providing anti-fogging or de-icing in optics and optoelectronic devices, as well as for wearable heating systems.

A facile patterning of silver nanowires using a magnetic printing method.

Patterning of metal nanowires (NWs) is vital for the fabrication of NW-based, high-performance devices such as sensors, transparent conducting electrodes, and optoelectronics. However, the majority of existing patterning methods require complex and expensive technologies. For this reason, we report for the first time a facile and quick patterning method of silver (Ag) NWs using a magnetic printing method. We successfully demonstrated a patterned AgNW grid structure ona flexible substrate as transparent electrodes. The flexible AgNW grid electrode exhibited optical and electrical properties comparable to those of commercial transparent conducting electrodes.We believe our work will be broadly applicable to other NW-based devices such as sensors,energy storage devices, meta devices, nanoscale electronics, and optoelectronics.

Observation of convection phenomenon by high-performance transparent heater based on Pt-decorated Ni micromesh

In this study, we report for the first time on the convection phenomenon for the consistent and sensitive detection of target materials (particulate matter (PM) or gases) with a high-performance transparent heater. The high-performance transparent heater, based on Pt-decorated Ni micromesh, was fabricated by a combination of transfer printing process and Pt sputtering. The resulting transparent heater exhibited excellent mechanical durability, adhesion with substrates, flexibility, and heat-generating performance. We monitored the changes in the PM concentration and temperature in an airtight chamber while operating the heater. The temperature in the chamber was increased slightly, and the PM2.5 concentration was increased by approximately 50 times relative to the initial state which PM is deposed in the chamber. We anticipate that our experimental findings will aid in the development and application of heaters for sensors and actuators as well as transparent electrodes and heating devices.

Rapid Low-Temperature 3D Integration of Silicon Nanowires on Flexible Substrates.

The vertical integration of 1D nanostructures onto the 2D substrates has the potential to offer significant performance gains to flexible electronic devices due to high integration density, large surface area, and improved light absorption and trapping. A simple, rapid, and low temperature transfer bonding method has been developed for this purpose. Ultrasonic vibration is used to achieve a low temperature bonding within a few seconds, resulting in a polymer-matrix-free, electrically conducting vertical assembly of silicon nanowires (SiNWs) with a graphene/PET substrate. The microscopic structure, and mechanical and electrical characteristics of the interface between the transferred SiNW array and graphene layer are subsequently investigated, revealing that this creates a mechanically robust and electrically Ohmic contact. This newly developed ultrasonic transfer bonding technique is also found to be readily adaptable for diverse substrates of both metal and polymer. It is therefore considered as a valuable technique for integrating 1D vertical nanostructures onto the 2D flexible substrates for flexible photovoltaics, energy storage, and water splitting systems.

Effect of hydrothermal condition on the formation of multi-component oxides of Ni-based metallic glass under high temperature water near the critical point

The specific feature of multi-component oxides synthesized by hydrothermal process under high temperature (633 K) and highly pressurized water (18.9 MPa) near critical point. Effects of hydrothermal processing duration times 24 hours and 72 hours, respectively, on the oxide formation of the Ni59Zr20Ti16Si2Sn3 metallic glass synthesized by powder metallurgy process were characterized by X-ray diffractometer, differential scanning calorimeter along with the particle size, morphology and crystalline phase of the oxides. The crystallization of the needle-shape NiTiO3, ZrTiO4 and ZrSnO4 ternary oxide phases observed on the surface of metallic glass at below glass transition temperature and the morphology of oxide phases changed to plate-shape around 2 μm in diameter by the increase processing time. This hydrothermal processing in subcritical water provides accelerated dense metal oxide crystals due to the reaction medium being at higher pressure than conventional oxidation processing.

Erratum: “Effect of hydrothermal condition on the formation of multi-component oxides of Ni-based metallic glass under high temperature water near the critical point” [AIP Advances 5, 077132 (2015)]

In the original manuscript, M. H. Lee’s affiliation number was incorrectly listed as 1. M. H. Lee’s correct affiliation number is 2 (Rare Metals R&D Group, Korea Institute of Industrial Technology, Incheon 406-840, South Korea). Furthermore, this change affects no other part of the paper.

The sensing characteristics of MOPS structure based on porous silicon for ethanol gas

To use the porous silicon as gas sensors, we made the MOPS structure from the porous silicon with Al evaporation and investigated the sensing characteristic of ethanol. When the MOPS structure is in contact with ethanol gas, the maximum peak of PL changes and it return to original intensity without contact. The MOPS structure had response time 0.78s and recovery time 4.13s when it is in contact with ethanol, which satisfied the required sensor standards. Further complimentary researches, however, are required to investigate the contact mechanism between MOPS structure and ethanol and to solve the surface contamination problem.