Hee-Seon Choi

Micellar colorimetric determination of iron, cobalt, nickel and copper using 1-nitroso-2-naphthol.

1-Nitroso-2-naphthol, an excellent color-forming chelating agent, combines to Fe(III), Co(II), Ni(II), Cu(II) and so on to form slightly soluble complexes in aqueous solution. To determine these metal ions, a tedious and time consuming separation technique, such as liquid-liquid extraction, has often been performed. However, these metal-1-nitroso-2-naphthol complexes could be determined conveniently by ultraviolet-visible (UV-Vis) spectrophotometry in Tween 80 micellar medium that has polyoxyethylene groups. After conditions such as pH, the amount of 1-nitroso-2-naphthol and the stability were adjusted to their optimum values, the sensitivities of the metal ions in Tween 80 medium and in chloroform were compared. It was shown that the sensitivities of Fe(III) and Co(II) in Tween 80 medium were higher than in chloroform, but that of Cu(II) was lower. The interfering effects among analytes ions, Fe(III), Co(II), Ni(II) and Cu(II) were more serious than by other ions, but the interfering effects could be removed by adjusting pH or adding the masking agents such as NH(3) or oxalate. Detection limits of Fe(III), Co(II), Ni(II), and Cu(II) were 0.024, 0.016, 0.039 and 0.023 mug ml(-1), respectively, and the correlation coefficients of these calibration curves were above 0.996. Recovery yields of the metal ions in the mixed standard solution ranged from 96 to 103%, and their coefficients of variation were low ranging between 0.94 and 1.75%. Cu(II) in brass sample and the amount of Fe(III) in steel sample were also determined. This proposed technique is simple, convenient and speedy.

Spectrofluorimetric determination of copper(II) by its static quenching effect on the fluorescence of 4,5-dihydroxy-1,3-benzenedisulfonic acid.

A spectrofluorimetric method has been developed for the determination of trace Cu(II) in real samples with 4,5-dihydroxy-l,3-benzenedisulfonic acid (Tiron) as a fluorimetric reporter. Tiron is very soluble in water and is a good fluorimetric reagent. However, as Tiron was complexed with Cu(II), the fluorescence intensity decreased proportionally to the concentration of Cu(II) by a static quenching effect. The excitation wavelength and the fluorescence wavelength of Tiron were 294 and 350 nm, respectively, as it was caused by a quenching effect from Cu(II) at pH 8.0. The highest sensitivity was shown at Tiron concentration of 5.0x10(-5) M. To enhance the quenching effect, the Cu(II)-Tiron complex solution was heated up to 80 degrees C for 90 min. As for Cu(II), the interference by Co(II) was very serious, which was eliminated by oxalate ion. The linear response to Cu(II) was shown at the concentration range between 5.0x10(-7) and 1.0x10(-5) M. With this proposed method, the detection limit of Cu(II) was 3.83(+/-0.09)x10(-7) M. Recoveries of Cu(II) in the diluted brass samples and the stream water samples were almost 100%. Based on results from the experiment, this proposed technique could be applied to the practical determination of Cu(II) in real samples.

Spectrofluorimetric determination of EDTA with Cu(II)-tiron chelate

A spectrofluorimetric method for the determination of EDTA in real samples such as mayonnaise, powder detergent and cleansing cream with tiron (4,5-dihydroxy-1,3-benzenedisulfonic acid) as a fluorimetric reporter was developed. When tiron is chelated with Cu(II), the fluorescent intensity is decreased by a quenching effect. However, when Cu(II)-tiron chelate reacts with EDTA, fluorescent intensity is increased as tiron is released. Several experimental conditions such as pH of the sample solution, the amount of Cu(II), the amount of tiron, heating temperature and heating time were optimized. Fe(III) interfered more seriously than any other ions, interference of Fe(III) could be disregarded, because Fe(III) was scarcely contained in selected real samples. The linear range of EDTA was from to . With this proposed method, the detection limit of Fe(III) was . Recovery yields of 92.7~99.3% were obtained. Based on experimental results, it is proposed that this technique can be applied to the practical determination of EDTA.