Hsiang Hsi Lin

Dynamic loading of spur gears with linear or parabolic tooth profile modifications

A computer simulation was conducted to investigate the effects of both linear and parabolic tooth profile modification on the dynamic response of low-contact-ratio spur gears. The effect of the total amount of modification and the length of the modification zone were studied at various loads and speeds to find the optimal profile modification for minimal dynamic loading. Design charts consisting of normalized maximum dynamic load curves were generated for gear systems operated at various loads and with different tooth profile modification. An optimum profile modification can be determined from these design charts to minimize the dynamic loads of spur gear systems.

Influence of Linear Profile Modification and Loading Conditions on the Dynamic Tooth Load and Stress of High Contact Ratio Gears

This paper presents a computer simulation for the dynamic response of high-contact-ratio spur gear transmissions.High contact ratio gears have the potential to produce lower dynamic tooth loads and minimum root stress but they can be sensitive to tooth profile errors. The analysis presented in this paper examines various profile modifications under realistic loading conditions. The effect of these modifications on the dynamic load (force) between mating gear teeth and the dynamic root stress is presented. Since the contact stress is dependent on the dynamic load, minimizing dynamic loads will also minimize contact stresses. This paper shows that the combination of profile modification and the applied load (torque) carried by a gear system has a significant influence on gear dynamics. The ideal modification at one value of applied load will not be the best solution for a different load. High contact ratio gears were found to require less modification than standard low-contact-ratio gears.

Computer-Aided Design of High-Contact-Ratio Gears for Minimum Dynamic Load and Stress

This paper presents a numerical procedure for minimizing dynamic effects on high-contact-ratio gears by modification of the tooth profile. The paper examines and compares both linear and parabolic tooth profile modifications of high-contact-ratio gears under various loading conditions. The effects of the total amount of modification and the length of the modification zone were systematically studied at various loads and speeds to find the optimum profile design for minimizing the dynamic load and the tooth bending stress. Parabolic profile modification is preferred over linear profile modification for high-contact-ratio gears because of its lower sensitivity to manufacturing errors. For parabolic modification a greater amount of modification at the tooth tip and a longer modification zone are required. Design charts are presented for high-contact-ratio gears with various profile modifications operating under a range of loads. A procedure is illustrated for using the charts to find the optimum profile design.

Using Dynamic Analysis for Compact Gear Design

Abstract : This paper presents procedures for designing compact spur gear sets with the objective of minimizing the gear size. The allowable tooth stress and dynamic response are incorporated in the process to obtain a feasible design region. Various dynamic rating factors were investigated and evaluated. The constraints of contact stress limits and involute interference combined with the tooth bending strength provide the main criteria for this investigation. A three-dimensional design space involving the gear size, diametral pitch, and operating speed was developed to illustrate the optimal design of spur gear pairs. The study performed here indicates that as gears operate over a range of speeds, variations in the dynamic response change the required gear size in a trend that parallels the dynamic factor. The dynamic factors are strongly affected by the system natural frequencies. The peak values of the dynamic factor within the operating speed range significantly influence the optimal gear designs. The refined dynamic factor introduced in this study yields more compact designs than AGMA dynamic factors.

Prediction of Gear Dynamics Using Fast Fourier Transform of Static Transmission Error

ABSTRACT An analytical computer simulation procedure for dynamic modeling of low-contact-ratio spur gear systems is presented. The procedure computes the gear static transmission error and uses a Fast Fourier Transform (FFT) to generate its frequency spectrum at various tooth profile modifications. The dynamic loading response of an unmodified (perfect involut) gear pair is compared with that of gears with profile modifications. Correlations are found between several profile modifications and the resulting dynamic loads. An effective error, obtained from frequency domain anal

Dynamic analysis of spur gears using computer program DANST

DANST is a computer program for static and dynamic analysis of spur gear systems. The program can be used for parametric studies to predict the effect on dynamic load and tooth bending stress of spur gears due to operating speed, torque, stiffness, damping, inertia, and tooth profile. DANST performs geometric modeling and dynamic analysis for low- or high-contact-ratio spur gears. DANST can simulate gear systems with contact ratio ranging from one to three. It was designed to be easy to use, and it is extensively documented by comments in the source code. This report describes the installation and use of DANST. It covers input data requirements and presents examples. The report also compares DANST predictions for gear tooth loads and bending stress to experimental and finite element results. 14 refs.

Using Hob Offset to Balance Dynamic Strength in Spur Gears

An analytical study of the effect of hob offset on dynamic tooth strength of spur gears is presented. The study was limited to equal and opposite offset values applied to the pinion and gear to maintain the standard operating center distance. The analysis presented is performed using a new version of the NASA gear dynamics code DANST. The operating speed of a transmission has a significant influence on the amount of hob offset required to equalize dynamic stresses in the pinion and gear. In the transmission studied, at low speeds, the optimum hob offset was found to fluctuate within a range. At higher speeds, the optimum value is constrained by the minimum allowed thickness at the tip of the pinion tooth. For gears that must operate over a range of speeds, an average offset value can be used. Spur gears designed with the procedure presented here can have significant improvements in load capacity.