Hyejin Moon

Creating, transporting, cutting, and merging liquid droplets by electrowetting-based actuation for digital microfluidic circuits

Reports the completion of four fundamental fluidic operations considered essential to build digital microfluidic circuits, which can be used for lab-on-a-chip or micro total analysis system (/spl mu/TAS): 1) creating, 2) transporting, 3) cutting, and 4) merging liquid droplets, all by electrowetting, i.e., controlling the wetting property of the surface through electric potential. The surface used in this report is, more specifically, an electrode covered with dielectrics, hence, called electrowetting-on-dielectric (EWOD). All the fluidic movement is confined between two plates, which we call parallel-plate channel, rather than through closed channels or on open surfaces. While transporting and merging droplets are easily verified, we discover that there exists a design criterion for a given set of materials beyond which the droplet simply cannot be cut by EWOD mechanism. The condition for successful cutting is theoretically analyzed by examining the channel gap, the droplet size and the degree of contact angle change by electrowetting on dielectric (EWOD). A series of experiments is run and verifies the criterion.

Low voltage electrowetting-on-dielectric

This article discusses and experimentally verifies how to lower the operating voltage that drives liquid droplets by the principle of electrowetting on dielectric (EWOD). A significant contact angle change (120°→80°) is desired to reliably pump the droplet in microchannels for applications such as lab-on-a-chip or micrototal analysis systems. Typically, much higher voltages (>100 V) are used to change the wettability of an electrolyte droplet on a dielectric layer compared with a conductive layer. The required voltage can be reduced by increasing the dielectric constant and decreasing the thickness of the dielectric layer, thus increasing the capacitance of the insulating layer. This dependence of applied voltage on dielectric thickness is confirmed through EWOD experiments for three different dielectric materials of varying thickness: Amorphous fluoropolymer (Teflon® AF, Dupont), silicon dioxide (SiO2) and parylene. The dependence on the dielectric constant is confirmed with two different dielectric mate...

Electrowetting and electrowetting-on-dielectric for microscale liquid handling

This paper deals with electrowetting (EW) and electrowetting-on-dielectric (EWOD) principles applied to microfluidic devices. EW and EWOD are principles that can control wettability of liquids on solid surfaces using electric potential. While EW is controlling wettability of a certain electrolyte on a metal electrode by varying electric energy across the electrical double layer (EDL), EWOD applies to virtually any aqueous liquid by varying electric energy across the thin dielectric film between the liquid and conducting substrate. These driving mechanisms have many advantages. By electrically changing the wettability of each of the electrode patterns on a surface, a liquid on these electrodes can be shaped and driven along the active electrodes, making microfluidics extremely simple both for device fabrication and operation. It is also worth noting that, driven by surface tension, the mechanism becomes more effective as the size of the device becomes smaller. This paper describes fundamental concepts and the proof-of-concept experiments, modeling and design, microfabrication processes, and initial testing results for the microfluidic devices based on the EW and EWOD principles.

Light actuation of liquid by optoelectrowetting

Optical actuation of liquid droplets has been experimentally demonstrated for the first time using a novel optoelectrowetting (OEW) principle. The optoelectrowetting surface is realized by integrating a photoconductive material underneath a two-dimensional array of electrowetting electrodes. Contact angle change as large as 308 has been achieved when illuminated by a light beam with an intensity of 65 mW/cm 2 . A micro-liter droplet of deionized water has been successfully transported by a 4 mW laser beam across a 1 cm � 1 cm OEW surface. The droplet speed is measured to be 7 mm/s. Light actuation enables complex microfluidic functions to be performed on a single chip without encountering the wiring bottleneck of two-dimensional array of electrowetting electrodes. Published by Elsevier Science B.V.

Equilibrium behavior of sessile drops under surface tension, applied external fields, and material variations

This article describes the equilibrium shape of a liquiddrop under applied fields such as gravity and electrical fields, taking into account material properties such as dielectric constants, resistivities, and surface tension coefficients. The analysis is based on an energy minimization framework. A rigorous and exact link is provided between the energy function corresponding to any given physical phenomena, and the resulting shape and size dependent force term in Young’s equation. In particular, the framework shows that a physical effect, such as capacitive energy storage in the liquid, will lead to 1/R “line-tension”-type terms if and only if the energy of the effect is proportional to the radius of the liquiddrop: E∝R. The effect of applied electric fields on shape change is analyzed. It is shown that a dielectric solid and a perfectly conducting liquid are all that is needed to exactly recover the Young–Lippmann equation. A dielectric liquid on a conducting solid gives rise to line tension terms. Finally, a slightly resistiveliquid on top of a dielectric, highly resistive solid gives rise to contact angle saturation and accurately matches the experimental data that we observe in our electro-wetting-on-dielectric devices.

Towards digital microfluidic circuits: creating, transporting, cutting and merging liquid droplets by electrowetting-based actuation

This paper reports a breakthrough in our quest for digital microfluidic circuits - full completion of all four fundamental microfluidic operations: (1) creating, (2) transporting, (3) cutting, and (4) merging of liquid droplets, based on electrowetting-on-dielectric (EWOD) actuation. All the operations were achieved with 25 V/sub DC/ lower than EWOD actuation voltages previously reported. We also report conditions to reduce the driving voltage even further and conditions to drive a droplet as fast as 250 mm/s.

Enhancement of mixing by droplet-based microfluidics

Enhancement of mixing using electrowetting-on-dielectric (EWOD) actuation is demonstrated. Exponential improvement over simple diffusion is theorized, based on convolutions generated by discrete droplet flow. The relationship between particle size, distance diffused, and diffusion time is studied. An improvement of 50 times over simple diffusion is experimentally shown, using a simple dye-mixing experiment.

Addressable micro liquid handling by electric control of surface tension

This paper presents two types of electrowetting principles - regular electrowetting (EW) and electrowetting on dielectric (EWOD), applied for microactuation and correspondingly designed test devices for addressable micro liquid handling. The devices demonstrated sequential microactuation of liquid on electrodes with (EWOD) or without (EW) hydrophobic coating on them.

On-Chip Drop-to-Drop Liquid Microextraction Coupled with Real-Time Concentration Monitoring Technique

This paper demonstrates a novel drop-to-drop liquid-liquid micro-extraction (DTD-LLME) device, which is based on an electrowetting on dielectric (EWOD) digital microfluidic chip. Droplets of two immiscible liquids, one of which is an ionic liquid, are formed in nanoliter volumes, driven along electrodes, merged and mixed for extraction, and finally separated upon the completion of the extraction process. All the steps are carried out on a microfluidic chip using combined electrowetting and dielectrophoretic forces, which act on the droplet upon the application of electric potential. Specially, the phase separation of two immiscible nanoliter-scale liquid drops was achieved for the first time on an EWOD digital microfluidic chip. To study the on-chip extraction kinetics, an image-based concentration measurement technique with suitable color parameters was studied and compared with the typical UV absorption based technique. Finally, the effect of applied ac voltage frequency on the extraction kinetics was studied. The observations on DTD-LLME, particularly phase separation, are discussed. The image-based method was found to be applicable for precise concentration measurements with the right choice of the color parameter. Results from experiments on finding the frequency dependence on extraction kinetics demonstrate that the application of higher frequencies can be a factor in accelerating the extraction on the proposed microextraction device.

A fundamental study on electrowetting by traditional and multifunctional ionic liquids: possible use in electrowetting on dielectric-based microfluidic applications.

Water or aqueous electrolytes are the dominant components in electrowetting on dielectric (EWOD)-based microfluidic devices. Low thermal stability, evaporation, and a propensity to facilitate corrosion of the metal parts of integrated circuits or electronics are drawbacks of aqueous solutions. The alternative use of ionic liquids (ILs) as electrowetting agents in EWOD-based applications or devices could overcome these limitations. Efficient EWOD devices could be developed using task-specific ILs. In this regard, a fundamental study on the electrowetting properties of ILs is essential. Therefore electrowetting properties of 19 different ionic liquids, including mono-, di-, and tricationic, plus mono- and dianionic ILs were examined. All tested ILs showed electrowetting of various magnitudes on an amorphous flouropolymer layer. The effects of IL structure, functionality, and charge density on the electrowetting properties were studied. The enhanced stability of ILs in electrowetting on dielectric at higher voltages was studied in comparison with water. Deviations from classical electrowetting theory were confirmed. The physical properties of ILs and their electrowetting properties were tabulated. These data can be used as references to engineer task-specific electrowetting agents (ILs) for future electrowetting-based applications.