In-Hee Hwang

Recovery of solid fuel from municipal solid waste by hydrothermal treatment using subcritical water

Hydrothermal treatments using subcritical water (HTSW) such as that at 234°C and 3MPa (LT condition) and 295°C and 8MPa (HT condition) were investigated to recover solid fuel from municipal solid waste (MSW). Printing paper, dog food (DF), wooden chopsticks, and mixed plastic film and sheets of polyethylene, polypropylene, and polystyrene were prepared as model MSW components, in which polyvinylchloride (PVC) powder and sodium chloride were used to simulate Cl sources. While more than 75% of carbon in paper, DF, and wood was recovered as char under both LT and HT conditions, plastics did not degrade under either LT or HT conditions. The heating value (HV) of obtained char was 13,886-27,544 kJ/kg and was comparable to that of brown coal and lignite. Higher formation of fixed carbon and greater oxygen dissociation during HTSW were thought to improve the HV of char. Cl atoms added as PVC powder and sodium chloride to raw material remained in char after HTSW. However, most Cl originating from PVC was found to converse into soluble Cl compounds during HTSW under the HT condition and could be removed by washing. From these results, the merit of HTSW as a method of recovering solid fuel from MSW is considered to produce char with minimal carbon loss without a drying process prior to HTSW. In addition, Cl originating from PVC decomposes into soluble Cl compound under the HT condition. The combination of HTSW under the HT condition and char washing might improve the quality of char as alternative fuel.

Pretreatment of automobile shredder residue (ASR) for fuel utilization

Automobile shredder residue (ASR) was pretreated to improve its quality for fuel utilization. Composition analysis revealed that ASR components could be classified into four groups: (1) urethane and textile-light fraction and combustibles containing low levels of ash and Cl; (2) plastics and rubber-light or heavy fraction and combustibles containing high levels of Cl; (3) metals and electrical wire-heavy fraction and incombustibles, and (4) particles smaller than 5.6mm with high ash contents. Based on these results, we successively performed sieving to remove particles smaller than 5.6mm, float and sink separations to reject the heavy fraction and plastics and rubber containing Cl, thermal treatment under an inert atmosphere to remove Cl derived from PVC, and char washing to remove soluble chlorides. This series of pretreatments enabled the removal of 78% of the ash and 91% of the Cl from ASR. Sieving using a 5.6-mm mesh removed a considerable amount of ash. Product quality was markedly improved after the float and sink method. Specifically, the sink process using a 1.1 g cm(-3) medium fluid rejected almost all rubber containing Cl and a large amount of PVC. The remaining Cl in char, after heating at 300 degrees C under an inert atmosphere and washing, was considered to be present as insoluble chlorides that volatilized at temperatures above 300 degrees C. Based on a tradeoff relationship between product quality and treatment cost, ASR may be utilized as a form of refuse plastic fuel or char.

Removal and speciation of mercury compounds in flue gas from a waste incinerator.

ABSTRACT The management and control of mercury emissions from waste incinerators have become more significant, because waste incinerators are sinks to treat mercury-containing consumer products. This study investigated the effects of mercury concentrations and waste incineration temperatures on mercury speciation using a lab-scale experimental instrument. The removal characteristics of different mercury species were also investigated using an apparatus to simulate the fabric filter with a thin layer of additives such as Ca(OH)2 and NaHCO3, activated carbon (AC), and fly ash. HgCl2 generation rates peaked at 800°C for initial Hg0 concentrations of 0.08−3.61 mg/Nm3 in the presence of 400 ppm HCl. A linear relationship was established between the generation rate of HgCl2 and the logarithmic value of initial mercury concentration. Fly ash proved highly efficient in mercury removal, being equal or superior to AC. On the other hand, Ca(OH)2 and NaHCO3 were shown to have no effects on mercury removal. In the dry-scrubbing process, alkali agent is often sprayed in amounts beyond those stoichiometrically required to aid acidic gas removal. The research suggests, however, that this may hinder mercury removal from the flue gas of solid waste incinerators.

Subcritical hydrothermal treatment for the recovery of liquid fertilizer from scallop entrails

Scallop entrails are organic wastes containing abundant proteins and minerals but are considered difficult to recycle because of high cadmium concentrations. In this work, the current problem of scallop entrails recycling was investigated and a subcritical hydrothermal treatment (SCHT) was examined for the recovery of liquid fertilizer from scallop entrails. Scallop entrails are mainly recycled for composting and feedstuff production. However, the dilution by mixing scallop entrails with other feed waste was the sole countermeasure to reduce the cadmium concentration of compost. For feedstuff production, whole product derived from scallop entrails was exported to other countries instead of domestic utilization. Temperature, retention time (RT) at given temperature, and liquid-to-solid (LS) ratio were examined as SCHT conditions for scallop entrails processing. The extraction ratio of each constituent mainly depends on the temperature rather than the RT or the LS ratio. Upon the SCHT of scallop entrails at 200°C, an RT of 20 min, and an LS ratio of 10, the extraction of fertilizer constituents such as nitrogen, phosphorus, and potassium from the liquid product was optimum, whereas the release of cadmium was suppressed. The concentrations of heavy metals in the liquid product obtained using the above-mentioned SCHT conditions were below the maximum permissible concentration stipulated by the Fertilizer Control Law. SCHT is considered to be a feasible recycling method for scallop entrails to recover fertilizer components with a concomitant separation of cadmium from the product.

Decomposition of organochlorine compounds in flue gas from municipal solid waste incinerators using natural and activated acid clays

High-temperature particle control (HTPC) using a ceramic filter is a dust collection method without inefficient cooling and reheating of flue gas treatment; thus, its use is expected to improve the energy recovery efficiency of municipal solid waste incinerators (MSWIs). However, there are concerns regarding de novo synthesis and a decrease in the adsorptive removal efficiency of dioxins (DXNs) at approximately 300°C. In this study, the effect of natural and activated acid clays on the decomposition of monochlorobenzene (MCB), one of the organochlorine compounds in MSW flue gas, was investigated. From the results of MCB removal tests at 30–300°C, the clays were classified as adsorption, decomposition, and low removal types. More than half of the clays (four kinds of natural acid clays and two kinds of activated acid clays) were of the decomposition type. In addition, the presence of Cl atoms detached from MCB was confirmed by washing the clay used in the MCB removal test at 300°C. Activated acid clay was expected to have high dechlorination performance because of its proton-rich-composition, but only two clays were classed as decomposition type. Conversely, all the natural acid clays used in this work were of the decomposition type, which contained relatively higher di- and trivalent metal oxides such as Al2O3, Fe2O3, MgO, and CaO. These metal oxides might contribute to the catalytic dechlorination of MCB at 300°C. Therefore, natural and activated acid clays can be used as alternatives for activated carbon at 300°C to remove organochloride compounds such as DXNs. Their utilization is expected to mitigate the latent risks related to the adoption of HTPC, and also to contribute to the improvement of energy recovery efficiency of MSWI. Implications The effect of natural and activated acid clays on MCB decomposition was investigated to evaluate their suitability as materials for the removal of organochlorine compounds, such as DXNs, from MSWI flue gas at approximately 300°C. More than half of the clays used in this study showed the decomposition characteristics of MCB. The presence of Cl atoms in the clay used in the MCB removal test at 300°C proved the occurrence of MCB decomposition. The results of this study suggest a novel flue gas treatment method to establish high-energy efficient MSWI systems.