J.E. Hoffman

Ultrahigh transmission optical nanofibers

We present a procedure for reproducibly fabricating ultrahigh transmission optical nanofibers (530 nm diameter and 84 mm stretch) with single-mode transmissions of 99.95 ± 0.02%, which represents a loss from tapering of 2.6  ×  10−5 dB/mm when normalized to the entire stretch. When controllably launching the next family of higher-order modes on a fiber with 195 mm stretch, we achieve a transmission of 97.8 ± 2.8%, which has a loss from tapering of 5.0  ×  10−4 dB/mm when normalized to the entire stretch. Our pulling and transfer procedures allow us to fabricate optical nanofibers that transmit more than 400 mW in high vacuum conditions. These results, published as parameters in our previous work, present an improvement of two orders of magnitude less loss for the fundamental mode and an increase in transmission of more than 300% for higher-order modes, when following the protocols detailed in this paper. We extract from the transmission during the pull, the only reported spectrogram of a fundamental mode launch that does not include excitation to asymmetric modes; in stark contrast to a pull in which our cleaning protocol is not followed. These results depend critically on the pre-pull cleanliness and when properly following our pulling protocols are in excellent agreement with simulations.

Intermodal energy transfer in a tapered optical fiber: optimizing transmission

We present an experimental and theoretical study of the energy transfer between modes during the tapering process of an optical nanofiber through spectrogram analysis. The results allow optimization of the tapering process, and we measure transmission in excess of 99.95% for the fundamental mode. We quantify the adiabaticity condition through calculations and place an upper bound on the amount of energy transferred to other modes at each step of the tapering, giving practical limits to the tapering angle.

A low-loss photonic silica nanofiber for higher-order modes

Optical nanofibers confine light to subwavelength scales, and are of interest for the design, integration, and interconnection of nanophotonic devices. Here we demonstrate high transmission (> 97%) of the first family of excited modes through a 350 nm radius fiber, by appropriate choice of the fiber and precise control of the taper geometry. We can design the nanofibers so that these modes propagate with most of their energy outside the waist region. We also present an optical setup for selectively launching these modes with less than 1% fundamental mode contamination. Our experimental results are in good agreement with simulations of the propagation. Multimode optical nanofibers expand the photonic toolbox, and may aid in the realization of a fully integrated nanoscale device for communication science, laser science or other sensing applications.

Rayleigh scattering in an optical nanofiber as a probe of higher-order mode propagation

Optical nanofibers provide a rich platform for exploring atomic and optical phenomena even when they support only a single spatial mode. Nanofibers supporting higher-order modes provide additional degrees of freedom to enable complex evanescent field profiles for interaction with the surrounding medium, but local control of these profiles requires nondestructive evaluation of the propagating fields. Here, we use Rayleigh scattering for rapid measurement of the propagation of light in few-mode optical nanofibers. Imaging the Rayleigh scattered light provides direct visualization of the spatial evolution of propagating fields throughout the entire fiber, including the transition from core-cladding guidance to cladding-air guidance. We resolve the interference between higher-order modes to determine local beat lengths and modal content along the fiber, and show that the modal superposition in the waist can be systematically controlled by adjusting the input superposition. With this diagnostic we can measure variations in the radius of the fiber waist to below 3 nm in situ using purely optical means. This nondestructive technique also provides useful insight into light propagation in optical nanofibers.

Higher order mode propagation in ultrathin optical fibers for atom traps

We have demonstrated efficient propagation of the first excited TE01, TM01, and HE21 modes in a nanofiber with a radius of 400 nm. As we decrease the taper angle from 4 mrad to 1 mrad, the propagation becomes more adiabatic and the transmission improves from 20% to 85%. We have also demonstrated that the choice of drawn fiber can have a significant impact on the propagation characteristics.

A hybrid quantum system of atoms trapped on ultrathin optical fibers coupled to superconductors

Hybrid quantum systems can be formed that combine the strengths of multiple platforms while avoiding the weaknesses. Here we report on progress toward a hybrid quantum system of neutral atom spins coupled to superconducting qubits. We trap laser-cooled rubidium atoms in the evanescent field of an ultrathin optical fiber, which will be suspended a few microns above a superconducting circuit that resonates at the hyperfine frequency of the Rb atoms, allowing magnetic coupling between the atoms and superconductor. As this will be done in a dilution refrigerator environment, the technical demands on the optical fiber is severe. We have developed and optimized a tapered fiber fabrication system, achieving optical transmission in excess of 99.95% , and fibers that can sustain 400 mW of optical power in a UHV environment. We have also optimized tapered fibers that can support higher order optical modes with high transmission (> 97%), which may be useful for different optical potential geometries. We have developed an in-situ tunable high-Q superconducting microwave resonator that can be tuned to within the resonator linewidth of the 6.8 GHz frequency of the Rb hyperfine transition.