J.L. Morenza

Depth profiling characterisation of the surface layer obtained by pulsed Nd:YAG laser irradiation of titanium in nitrogen

We investigated the composition of the surface layer obtained by pulsed Nd:YAG laser (λ=1.064 μm, τ∼120 ns, ν=1 kHz) irradiation of Ti targets in high pressure nitrogen. The surface morphology, the crystalline state, and the depth distribution of the elements were analysed by scanning electron microscopy, X-ray diffractometry, secondary ion mass spectrometry, X-ray photoelectron spectroscopy (XPS), and Auger electron spectroscopy. The chemical binding states were studied by deconvolution of the XPS spectra. The layer has a uniform surface, and mainly consists of the tetragonal δ′-TiNx crystalline phase. The nitrogen concentration increases firstly in the depth until approximately 0.15 μm, and then decreases until the greatest measured depth of 2 μm. The TiNx stoichiometry changes from x≈0.8 close to the surface to x≈0.5 at a depth of approximately 0.2 μm, it remains around this value until approximately 0.5 μm, and for greater depths decreases until 0.1 at 1.6 μm. Furthermore, the oxygen concentration decreases quickly and reaches the concentration of bulk Ti at approximately 0.2 μm.

Preparation of functional DNA microarrays through laser-induced forward transfer

A functional DNA microarray was prepared through the laser-induced forward transfer (LIFT) technique. In a first experiment, droplets of a buffer solution were spotted onto a substrate at different laser pulse energies. This allowed one to determine that uniform spots with a diameter as small as 40μm could be obtained. In a second experiment, a microarray containing two different human cDNAs and a negative control was spotted through LIFT and submitted to a hybridization assay. The obtained results demonstrated the full functionality of the microarray, which allowed us to prove the viability of LIFT for the production of DNA microarrays.

Mechanical properties of calcium phosphate coatings deposited by laser ablation

Amorphous calcium phosphate and crystalline hydroxyapatite coatings with different morphologies were deposited onto Ti-6Al-4V substrates by means of the laser ablation technique. The strength of adhesion of the coatings to the substrate and their mode of fracture were evaluated through the scratch test technique and scanning electron microscopy. The effect of wet immersion on the adhesion was also assessed. The mechanisms of failure and the critical load of delamination differ significantly depending on the phase and structure of the coatings. The HA coatings with granular morphology have higher resistance to delamination as compared to HA coatings with columnar morphology. This fact has been related to the absence of stresses for the granular morphology.

Laser-induced forward transfer of liquids: Study of the droplet ejection process

Laser-induced forward transfer LIFT is a laser direct-write technique that offers the possibility of printing patterns with a high spatial resolution from a wide range of materials in a solid or liquid state, such as conductors, dielectrics, and biomolecules in solution. This versatility has made LIFT a very promising alternative to lithography-based processes for the rapid prototyping of biomolecule microarrays. Here, we study the transfer process through the LIFT of droplets of a solution suitable for microarray preparation. The laser pulse energy and beam size were systematically varied, and the effect on the transferred droplets was evaluated. Controlled transfers in which the deposited droplets displayed optimal features could be obtained by varying these parameters. In addition, the transferred droplet volume displayed a linear dependence on the laser pulse energy. This dependence allowed determining a threshold energy density value, independent of the laser focusing conditions, which acted as necessary conditions for the transfer to occur. The corresponding sufficient condition was given by a different total energy threshold for each laser beam dimension. The threshold energy density was found to be the dimensional parameter that determined the amount of the transferred liquid per laser pulse, and there was no substantial loss of material due to liquid vaporization during the transfer.

Time-resolved imaging of the laser forward transfer of liquids

Time-resolved imaging is carried out to study the dynamics of the laser-induced forward transfer of an aqueous solution at different laser fluences. The transfer mechanisms are elucidated, and directly correlated with the material deposited at the analyzed irradiation conditions. It is found that there exists a fluence range in which regular and well-defined droplets are deposited. In this case, laser pulse energy absorption results in the formation of a plasma, which expansion originates a cavitation bubble in the liquid. After the further expansion and collapse of the bubble, a long and uniform jet is developed, which advances at a constant velocity until it reaches the receptor substrate. On the other hand, for lower fluences no material is deposited. In this case, although a jet can be also generated, it recoils before reaching the substrate. For higher fluences, splashing is observed on the receptor substrate due to the bursting of the cavitation bubble. Finally, a discussion of the possible mechanisms which lead to such singular dynamics is also provided.

Behavior in simulated body fluid of calcium phosphate coatings obtained by laser ablation.

Three types of calcium phosphate coatings onto titanium alloy substrates, deposited by the laser ablation technique, were immersed in a simulated body fluid in order to determine their behavior in conditions similar to the human blood plasma. Neither the hydroxyapatite coating nor the amorphous calcium phosphate coating do dissolve and the alpha-tricalcium phosphate phase of the coating of beta-tricalcium phosphate with minor alpha phase slightly dissolves. Precipitation of an apatitic phase is favored onto the hydroxyapatite coating and onto the coating of beta-tricalcium phosphate with minor alpha phase. Onto the titanium alloy substrate reference there is also precipitation but at larger induction times. However, onto the amorphous calcium phosphate coating no precipitate is formed.

Deposition of hydroxyapatite thin films by excimer laser ablation

Abstract The influence of the pressure of a sole water atmosphere during the pulsed laser deposition of hydroxyapatite thin films on Ti–6Al–4V substrates has been studied. The rest of the technological parameters involved in the process have been fixed near the conditions where the best crystalline coatings are obtained. The pressure of the water atmosphere has been varied between 0.15 and 1.5 mbar. The films properties have been analysed by means of XRD, SEM, FT-IR spectroscopy and SIMS. An optimal region, in order to obtain thin films of highly crystalline hydroxyapatite, has been found near 0.5 mbar for the two excimer laser wavelengths (193 nm and 248 nm) used in this study. These films have a preferential orientation in the (100) direction.

Whiskerlike structure growth on silicon exposed to ArF excimer laser irradiation

The effects of ArF excimer laser irradiation on silicon single crystals in air have been studied. The etch rate versus fluence curve shows three well defined zones, with very different etch rates and dependences. In the intermediate zone (from 1.5 to 2.5 J/cm2), narrow (1–2 μm diameter) and tall columns (3–30 μm) start to grow after irradiation with some hundreds of laser pulses. These whiskerlike columns, with height between one and two orders of magnitude higher than the depth of the crater, have not been formed by preferential etching of the surrounding material, but through hydrodynamical processes.

Influence of thickness on the properties of hydroxyapatite coatings deposited by KrF laser ablation

The growth of hydroxyapatite coatings obtained by KrF excimer laser ablation and their adhesion to a titanium alloy substrate were studied by producing coatings with thicknesses ranging from 170 nm up to 1.5 microm, as a result of different deposition times. The morphology of the coatings consists of grain-like particles and also droplets. During growth the grain-like particles grow in size, partially masking the droplets, and a columnar structure is developed. The thinnest film is mainly composed of amorphous calcium phosphate. The coating 350nm thick already contains hydroxyapatite, whereas thicker coatings present some alpha tricalcium phosphate in addition to hydroxyapatite. The resulting coating to substrate adhesion was evaluated through the scratch test technique. Coatings fail under the scratch test by spallating laterally from the diamond tip and the failure load increases as thickness decreases, until not adhesive but cohesive failure for the thinnest coating is observed.

On the Hall effect in polycrystalline semiconductors

Some problems involved in the interpretation of Hall‐effect measurements in polycrystalline semiconductors have not been resolved, especially when the contribution of the boundaries is appreciable. Using the Herring theory of transport properties in inhomogeneous semiconductors, we present an alternative interpretation to that previously proposed. This model permits the calculation of the Hall coefficient under general conditions.