Jae Ik Yoon

Factors governing hole expansion ratio of steel sheets with smooth sheared edge

Stretch-flangeability measured using hole expansion test (HET) represents the ability of a material to form into a complex shaped component. Despite its importance in automotive applications of advanced high strength steels, stretch-flangeability is a less known sheet metal forming property. In this paper, we investigate the factors governing hole expansion ratio (HER) by means of tensile test and HET. We correlate a wide range of tensile properties with HERs of steel sheet specimens because the stress state in the hole edge region during the HET is almost the same as that of the uniaxial tensile test. In order to evaluate an intrinsic HER of steel sheet specimens, the initial hole of the HET specimen is produced using a milling process after punching, which can remove accumulated shearing damage and micro-void in the hole edge region that is present when using the standard HER evaluation method. It was found that the intrinsic HER of steel sheet specimens was proportional to the strain rate sensitivity exponent and post uniform elongation.

Continuum understanding of twin formation near grain boundaries of FCC metals with low stacking fault energy

Deformation twinning from grain boundaries is often observed in face-centered cubic metals with low stacking fault energy. One of the possible factors that contribute to twinning origination from grain boundaries is the intergranular interactions during deformation. Nonetheless, the influence of mechanical interaction among grains on twin evolution has not been fully understood. In spite of extensive experimental and modeling efforts on correlating microstructural features with their twinning behavior, a clear relation among the large aggregate of grains is still lacking. In this work, we characterize the micromechanics of grain-to-grain interactions that contribute to twin evolution by investigating the mechanical twins near grain boundaries using a full-field crystal plasticity simulation of a twinning-induced plasticity steel deformed in uniaxial tension at room temperature. Microstructures are first observed through electron backscatter diffraction technique to obtain data to reconstruct a statistically equivalent microstructure through synthetic microstructure building. Grain-to-grain micromechanical response is analyzed to assess the collective twinning behavior of the microstructural volume element under tensile deformation. Examination of the simulated results reveal that grain interactions are capable of changing the local mechanical behavior near grain boundaries by transferring strain across grain boundary or localizing strain near grain boundary.Metals: grain neighbours influence twin formation during deformationGrains that should not favour twin formation exhibit twinning as a result of surrounding grains acting on their boundaries. A team led by HyoungSeop Kim at the Pohang University of Science and Technology in the Republic of Korea simulated the deformation of synthetic metallic microstructures with many grains of different orientations, based on steels that deform by both dislocation slip and twinning mechanisms. Twinning first started near grain boundaries and depended on initial grain orientation but, with further deformation, strong twin activity on one side of a boundary triggered strong twin activity on the other side of that boundary. This happened even when the grain on the other side of the boundary was unfavourable to twinning. Taking into account grain neighbourhood may therefore help in optimising twin-forming alloys.

Key factors of stretch-flangeability of sheet materials

Abstract Stretch-flangeability evaluated using hole-expansion testing represents the ability of sheet materials to resist edge fracture during complex shape forming. Despite a property imperative for automotive part applications of advanced high-strength steels, factors governing stretch-flangeability are not yet well understood. In this study, the mechanical properties of a selected group of materials with different microstructures were investigated using tensile, fracture toughness, and hole-expansion tests to find the factor governing the stretch-flangeability that is universally applicable to a variety of metallic materials. It was found that the fracture toughness of materials, measured using the fracture initiation energy, is a universal factor governing stretch-flangeability. We verified that fracture toughness is the key factor governing stretch-flangeability, showing that the hole-expansion ratio could be well predicted using finite element analysis associated with a simple ductile damage model, without explicitly taking into account the microstructural complexity of each specimen. This validates the use of the fracture toughness as a key factor of stretch-flangeability.

Effect of target-fixture geometry on shock-wave compacted copper powders

In shock compaction with a single gas gun system, a target fixture is used to safely recover a powder compact processed by shock-wave dynamic impact. However, no standard fixture geometry exists, and its effect on the processed compact is not well studied. In this study, two types of fixture are used for the dynamic compaction of hydrogen-reduced copper powders, and the mechanical properties and microstructures are investigated using the Vickers microhardness test and electron backscatter diffraction, respectively. With the assistance of finite element method simulations, we analyze several shock parameters that are experimentally hard to control. The results of the simulations indicate that the target geometry clearly affects the characteristics of incident and reflected shock waves. The hardness distribution and the microstructure of the compacts also show their dependence on the geometry. With the results of the simulations and the experiment, it is concluded that the target geometry affects the shock wave propagation and wave interaction in the specimen.

Surface Abrasive Torsion for Improved Mechanical Properties and Microstructure

A novel process of discrete surface abrasion during simple torsion (ST), named “surface abrasive torsion (SAT),” is proposed to overcome the limitation of ST, i.e., insufficient strain for severe plastic deformation (SPD) due to cracks initiated on the surface, by removing the roughened surface region. The effect of SAT on delayed crack initiation was explained using finite element simulations. Larger shear deformation applicable to the specimen in SAT than ST was demonstrated experimentally.