James Loomis

Solar steam generation by heat localization

Currently, steam generation using solar energy is based on heating bulk liquid to high temperatures. This approach requires either costly high optical concentrations leading to heat loss by the hot bulk liquid and heated surfaces or vacuum. New solar receiver concepts such as porous volumetric receivers or nanofluids have been proposed to decrease these losses. Here we report development of an approach and corresponding material structure for solar steam generation while maintaining low optical concentration and keeping the bulk liquid at low temperature with no vacuum. We achieve solar thermal efficiency up to 85% at only 10 kW m(-2). This high performance results from four structure characteristics: absorbing in the solar spectrum, thermally insulating, hydrophilic and interconnected pores. The structure concentrates thermal energy and fluid flow where needed for phase change and minimizes dissipated energy. This new structure provides a novel approach to harvesting solar energy for a broad range of phase-change applications.

Graphene-nanoplatelet-based photomechanical actuators

This paper reports large light-induced reversible and elastic responses of graphene nanoplatelet (GNP) polymer composites. Homogeneous mixtures of GNP/polydimethylsiloxane (PDMS) composites (0.1-5 wt%) were prepared and their infrared (IR) mechanical responses studied with increasing pre-strains. Using IR illumination, a photomechanically induced change in stress of four orders of magnitude as compared to pristine PDMS polymer was measured. The actuation responses of the graphene polymer composites depended on the applied pre-strains. At low levels of pre-strain (3-9%) the actuators showed reversible expansion while at high levels (15-40%) the actuators exhibited reversible contraction. The GNP/PDMS composites exhibited higher actuation stresses compared to other forms of nanostructured carbon/PDMS composites, including carbon nanotubes (CNTs), for the same fabrication method. An extraordinary optical-to-mechanical energy conversion factor (η(M)) of 7-9 MPa W(-1) for GNP-based polymer composite actuators is reported.

15.7% Efficient 10‐μm‐Thick Crystalline Silicon Solar Cells Using Periodic Nanostructures

Only ten micrometer thick crystalline silicon solar cells deliver a short-circuit current of 34.5 mA cm(-2) and power conversion efficiency of 15.7%. The record performance for a crystalline silicon solar cell of such thinness is enabled by an advanced light-trapping design incorporating a 2D inverted pyramid photonic crystal and a rear dielectric/reflector stack.

Charging-free electrochemical system for harvesting low-grade thermal energy

Significance Tremendous low-grade heat is stored in industrial processes and the environment. Efficient and low-cost utilization of the low-grade heat is critical to imminent energy and environmental challenges. Here, a rechargeable electrochemical cell (battery) is used to harvest such thermal energy because its voltage changes significantly with temperature. Moreover, by carefully tuning the composition of electrodes, the charging process is purely powered by thermal energy and no electricity is required to charge it. A high heat-to-electricity conversion efficiency of 2.0% can be reached when it is operated between 20 and 60 °C. Such charging-free characteristic may have potential application for harvesting low-grade heat from the environment, especially in remote areas. Efficient and low-cost systems are needed to harvest the tremendous amount of energy stored in low-grade heat sources (<100 °C). Thermally regenerative electrochemical cycle (TREC) is an attractive approach which uses the temperature dependence of electrochemical cell voltage to construct a thermodynamic cycle for direct heat-to-electricity conversion. By varying temperature, an electrochemical cell is charged at a lower voltage than discharge, converting thermal energy to electricity. Most TREC systems still require external electricity for charging, which complicates system designs and limits their applications. Here, we demonstrate a charging-free TREC consisting of an inexpensive soluble Fe(CN)63−/4− redox pair and solid Prussian blue particles as active materials for the two electrodes. In this system, the spontaneous directions of the full-cell reaction are opposite at low and high temperatures. Therefore, the two electrochemical processes at both low and high temperatures in a cycle are discharge. Heat-to-electricity conversion efficiency of 2.0% can be reached for the TREC operating between 20 and 60 °C. This charging-free TREC system may have potential application for harvesting low-grade heat from the environment, especially in remote areas.

Graphene/elastomer composite-based photo-thermal nanopositioners

The addition of nanomaterials to polymers can result not only in significant material property improvements, but also assist in creating entirely new composite functionalities. By dispersing graphene nanoplatelets (GNPs) within a polydimethylsiloxane matrix, we show that efficient light absorption by GNPs and subsequent energy transduction to the polymeric chains can be used to controllably produce significant amounts of motion through entropic elasticity of the pre-strained composite. Using dual actuators, a two-axis sub-micron resolution stage was developed, and allowed for two-axis photo-thermal positioning (~100 μm per axis) with 120 nm resolution (feedback sensor limitation), and ~5 μm/s actuation speeds. A PID control loop automatically stabilizes the stage against thermal drift, as well as random thermal-induced position fluctuations (up to the bandwidth of the feedback and position sensor). Maximum actuator efficiency values of ~0.03% were measured, approximately 1000 times greater than recently reported for light-driven polymer systems.

Layer dependent mechanical responses of graphene composites to near-infrared light

The authors report layer dependent physical responses of graphene-based polymer composites to near-infrared (NIR) light. Thin film polymer composites were fabricated and compared utilizing both single layer graphene and few layer graphene (∼5 layers). NIR-induced axial stress and kinetics were measured and found to exhibit three distinct pre-strain dependent response states. Composite stress responses, elastic moduli, and efficiencies were observed to depend on the number of graphene layers in the two-dimensional crystal.

Membrane-Free Battery for Harvesting Low-Grade Thermal Energy

Efficient and low-cost systems are desired to harvest the tremendous amount of energy stored in low-grade heat sources (<100 °C). An attractive approach is the thermally regenerative electrochemical cycle (TREC), which uses the dependence of electrode potential on temperature to construct a thermodynamic cycle for direct heat-to-electricity conversion. By varying the temperature, an electrochemical cell is charged at a lower voltage than discharged; thus, thermal energy is converted to electricity. Recently, a Prussian blue analog-based system with high efficiency has been demonstrated. However, the use of an ion-selective membrane in this system raises concerns about the overall cost, which is crucial for waste heat harvesting. Here, we report on a new membrane-free battery with a nickel hexacyanoferrate (NiHCF) cathode and a silver/silver chloride anode. The system has a temperature coefficient of -0.74 mV K(-1). When the battery is discharged at 15 °C and recharged at 55 °C, thermal-to-electricity conversion efficiencies of 2.6% and 3.5% are achieved with assumed heat recuperation of 50% and 70%, respctively. This work opens new opportunities for using membrane-free electrochemical systems to harvest waste heat.

Infrared-Transparent Visible-Opaque Fabrics for Wearable Personal Thermal Management

Personal cooling technologies locally control the temperature of an individual rather than a large space, thus providing personal thermal comfort while supplementing cooling loads in thermally regulated environments. This can lead to significant energy and cost savings. In this study, a new approach to personal cooling was developed using an infrared-transparent visible-opaque fabric (ITVOF), which provides passive cooling via the transmission of thermal radiation emitted by the human body directly to the environment. Here, we present a conceptual framework to thermally and optically design an ITVOF. Using a heat transfer model, the fabric was found to require a minimum infrared (IR) transmittance of 0.644 and a maximum IR reflectance of 0.2 to ensure thermal comfort at ambient temperatures as high as 26.1oC (79oF). To meet these requirements, an ITVOF design was developed using synthetic polymer fibers with an intrinsically low IR absorptance. These fibers were then structured to minimize IR reflection via weak Rayleigh scattering while maintaining visible opaqueness via strong Mie scattering. For a fabric composed of parallel-aligned polyethylene fibers, numerical finite element simulations predict 1 {\mu}m diameter fibers bundled into 30 {\mu}m yarns can achieve a total hemispherical IR transmittance of 0.972, which is nearly perfectly transparent to mid- and far-IR radiation. The visible wavelength properties of the ITVOF are comparable to conventional textiles ensuring opaqueness to the human eye. By providing personal cooling in a form amenable to everyday use, ITVOF-based clothing offers a simple, low-cost solution to reduce energy consumption in HVAC systems.

Load transfer and mechanical properties of chemically reduced graphene reinforcements in polymer composites

We report load transfer and mechanical properties of chemically derived single layer graphene (SLG) as reinforcements in poly (dimethyl) siloxane (PDMS) composites. Shear mixing reduced graphene sheets in polymers resulted in a marked decrease of the 2D band intensity due to doping and functionalization. Raman G mode shifts of 11.2 cm(-1)/% strain in compression and 4.2 cm(-1)/% strain in tension are reported. Increases in elastic modulus of PDMS by ~42%, toughness by ~39%, damping capability by ~673%, and strain energy density of ~43% by the addition of 1 wt% SLG in PDMS are reported.

Dimensional dependence of photomechanical response in carbon nanostructure composites: a case for carbon-based mixed-dimensional systems.

This paper reports dimensional dependence of the mechanical response in carbon nanostructure composites to near-infrared (NIR) light. Using polydimethylsiloxane, a common silicone elastomer, composites were fabricated with one-dimensional multi-wall carbon nanotubes (MWNTs), two-dimensional single-layer graphene, two-and-a-half-dimensional graphene nanoplatelets and three-dimensional highly ordered pyrolytic graphite. An evaporative mixing technique was utilized to achieve homogeneous dispersions of carbon in the polymer composites, and their photomechanical responses to NIR illumination were studied. For a given carbon concentration, both steady-state photomechanical stress response and energy conversion efficiency were found to be directly related to the dimensional state of the carbon nanostructure additive. A maximum observed stress change of ~60 kPa and ~5 × 10(-3)% efficiency were obtained with just 1 wt% MWNT loading. Actuation and relaxation kinetic responses were found to be related not to dimensionality, but to the percolation threshold of the carbon nanostructure additive in the polymer. Establishing a connective network of the carbon nanostructure additive allowed for energy transduction responsible for the photomechanical effect to activate carbon beyond the NIR illumination point, resulting in enhanced actuation. For samples greater than percolation threshold, photoconductivity of the nanocomposite structure as a function of applied pre-strain was measured. Photoconductive response was found to be inversely proportional to applied pre-strain, demonstrating mechanical coupling. Mechanical response dependence to the carbon nanostructure dimensional state could have significance in developing new types of carbon-based mixed-dimensional composites for sensor and actuator systems.