Jan Alstrup

A roll-to-roll process to flexible polymer solar cells: model studies, manufacture and operational stability studies

An inverted polymer solar cell geometry comprising a total of five layers was optimized using laboratory scale cells and the operational stability was studied under model atmospheres. The device geometry was substrate-ITO-ZnO-(active layer)-PEDOT:PSS-silver with P3HT-PCBM as the active layer. The inverted devices were compared to model devices with a normal geometry where the order of the layers was substrate-ITO-PEDOT:PSS-(active layer)-aluminium. In both cases illumination was through the substrate which requires that it is transparent. Both device types were optimized to a power conversion efficiency of 2.7% (1000 W m−2, AM1.5G, 72 ± 2 °C). The devices were operated under illumination while being subjected to different atmospheres to identify the dominant modes of degradation. Dry nitrogen (99.999%), dry oxygen (99.5%), humid nitrogen (90 ± 5% relative humidity) and ambient atmosphere (20% oxygen, 20 ± 5% relative humidity) were employed and both device types were found to be stable in a nitrogen atmosphere during the test period of 200 hours. The devices with a normal geometry where an aluminium electrode is employed gave stable operation in dry oxygen but did not give stable device operation in the presence of humidity. The inverted devices behaved oppositely where the less reactive silver electrode gave stable operation in the presence of humidity but poor stability in the presence of oxygen. The inverted model device was then used to develop a new process giving access to fully roll-to-roll (R2R) processed polymer solar cells entirely by solution processing starting from a polyethyleneterephthalate (PET) substrate with a layer of indium-tin-oxide (ITO). All processing was performed in air without vacuum coating steps and modules comprising eight serially connected cells gave power conversion efficiencies as high as 2.1% for the full module with 120 cm2 active area (AM1.5G, 393 W m−2) and up to 2.3% for modules with 4.8 cm2 active area (AM1.5G, 1000 W m−2).

Ultra Fast and Parsimonious Materials Screening for Polymer Solar Cells Using Differentially Pumped Slot-Die Coating

We present a technique that enables the probing of the entire parameter space for each parameter with good statistics through a simple roll-to-roll processing method where gradients of donor, acceptor, and solvent are applied by differentially pumped slot-die coating. We thus demonstrate how the optimum donor-acceptor ratio and device film thickness can be determined with improved accuracy by varying the composition in small steps. We give as an example P3HT-PCBM devices and vary the composition between P3HT and PCBM in steps of 0.5-1% giving 100-200 individual solar cells. The coating experiment itself takes less than 4-8 min and requires 15-30 mg each of donor and acceptor material. The optimum donor-acceptor composition of P3HT and PCBM was found to be a broad maximum centered on a 1:1 ratio. We demonstrate how the optimal thickness of the active layer can be found by the same method and materials usage by variation of the layer thickness in small steps of 1.5-4 nm. Contrary to expectation we did not find oscillatory variation of the device performance with device thickness because of optical interference. We ascribe this to the nature of the solar cell type explored in this example that employs nonreflective or semitransparent printed electrodes. We further found that very thick active layers on the order of 1 μm can be prepared without loss in performance and estimate the active layer thickness could easily approach 4-5 μm while maintaining photovoltaic properties.

Large area polymer solar cells

The fabrication of very large area polymer based solar cell modules with a total aperture area of 1000 cm2 has been accomplished. The substrate was polyethyleneterephthalate (PET) foil with a pre-etched pattern of indium-tin-oxide (ITO) anodes. The module was constructed as a matrix of 91 devices comprising 7 rows connected in parallel with each row having 13 individual cells connected in series. The printing of the organic layer employed screen printing of a chlorobenzene solution of the active material that consisted of either poly-1,4-(2-methoxy-5-ethylhexyloxy) phenylenevinylene (MEH-PPV) on its own or a 1:1 mixture (w/w) of MEH-PPV and [6,6]-phenyl-C61-butanoic acid methyl ester (PCBM). Our first results employed e-beam evaporation of the aluminium cathode directly onto the active layer giving devices with very poor performance that was discouragingly lower than expected by about three orders of magnitude. We found that e-beam radiation leads to a much poorer performance and thermal evaporation of the aluminium using a basket heater improved these values by an order of magnitude in efficiency for the geometry ITO/MEH-PPV/C60/Al. Finally the lifetimes (τ1/2) of the modules were established and were found to improve significantly when a sublimed layer of C60 was included between the polymer and the aluminium electrode. Values for the half life of 150 hours were typically obtained. This short lifetime is linked to reaction between the reactive metal electrode (aluminium) and the constituents of the active layer.

Three-dimensional chemical and physical analysis of the degradation mechanisms in organic photovoltaics

Insufficient lifetimes of organic photovoltaics are manifested in a reduced photovoltaic response, which is a consequence of physical and chemical degradation of the photovoltaic device. To prevent degradation it is vital to gain detailed insight into the degradation mechanisms. This is possible by utilizing state-of-the-art characterization techniques such as TOF-SIMS, XPS, AFM, SEM, interference microscopy and fluorescence microscopy as well as isotopic labeling (18O2 and H218O). By a combination of lateral and vertical analyses of the devices we obtain in-depth and in-plane information on the reactions and changes that take place in the various layers and interfaces. Examples will be presented that describe the advantages and disadvantages of various characterization techniques in relation to obtaining information on the degradation behavior of complete photovoltaic devices.

A process-line for large area organic solar cells

In this paper we would like to address the key role of fabrication in the performance and lifetime of organic photovoltaics. The realization of a complete process line for the construction of large area organic photovoltaics (250 x 400 mm) is described. Among many of the factors that influence organic solar cell lifetime, oxygen and water exposure is the most important. Multiple processes have to be performed under controlled atmosphere and a glove box (or glove boxes), which involves more volume than commercially available glove boxes, needs to house different instruments. The processes housed in the glove boxes were spin coating, evaporation, lamination/sealing and testing, under an inert atmosphere. The main strategy employed multiply connected glove boxes with one load lock. The first glove box was used for spin coating and lamination/sealing, the second will house a screen printer and the third one accommodate an evaporator completely build in house. The evaporator has 2 thermal evaporation sources and 2 e-beams with 4 and 1 crucibles. The process line should allow the entire device realization from substrate coating, to electrode evaporation including the sealing process avoiding air and water exposure. Organic solar cells from small test cells on ITO glass to big modules (250 x 400 mm) of 91 connected cells on ITO PET substrates were fabricated and characterized.