Jean-François Feller

Conductive polymer composites: comparative study of poly(ester)-short carbon fibres and poly(epoxy)-short carbon fibres mechanical and electrical properties

The effect of the addition of short carbon fibres (SCF) on the mechanical and electrical properties of conductive polymer composites (CPC) with poly(ester) and poly(epoxy) matrices has been studied. The reinforcement effect of (SCF) filled thermosets CPC is more important with poly(epoxy) than with poly(ester) matrix. Electrical measurements show a small amplitude PTC effect between 90 and 160 °C. The percolation threshold is reached for about 1% v/v SCF and higher conductivity is obtained with poly(ester) matrix. Up to 3% v/v, a good correlation is found between resistivity and relative Youngs modulus.

Conductive bio-Polymer nano-Composites (CPC): Chitosan-carbon nanotube transducers assembled via spray layer-by-layer for volatile organic compound sensing

The chemo-electrical properties of chitosan-carbon nanotubes (Chit-CNT) Conductive bio-Polymer nano-Composites (CPC) transducers processed by spray layer-by-layer (LbL) technique have been investigated. Results show that unlike most synthetic polymer matrices, chitosan provides the transducer with high sensitivity towards not only polar vapours like water and methanol but also to a lesser extent toluene. Quantitative responses are obtained, well fitted with the Langmuir-Henry-Clustering (LHC) model allowing to link electrical signal to vapour content. Chit-CNT transducers selectivity was also correlated with an exponential law to the inverse of Flory-Huggins interaction parameter chi(12). These properties make Chit-CNT a good transducer to be implemented in an e-nose. Additionally, the observation by atomic force microscopy (AFM) of Chit-CNT morphology suggests a chemical nano-switching mechanism promoting tunnelling conduction and originating macroscopic vapour sensing.

Novel architecture of carbon nanotube decorated poly(methyl methacrylate) microbead vapour sensors assembled by spray layer by layer

For the first time vapour sensors were made by assembling multi-wall carbon nanotube (CNT) decorated poly(methyl methacrylate) microbeads (PMMAµB) by spray layer by layer (sLbL). This combination of materials and technique resulted in an original hierarchical architecture with a segregated network of CNT bridging PMMAµB. The chemo-resistive behaviour of these conductive polymer nanocomposite (CPC) sensors was studied in terms of sensitivity and selectivity towards standard volatile organic compounds (VOC), as well as quantitativity and reproducibility of responses Ar to methanol, water, toluene and chloroform. Results show that 3D sLbL assembly allows boosting CNT network sensitivity by a factor 2 and selectivity for methanol vapour by a factor of 5. Additionally CNT-PMMAµB sensors gave responses proportional to vapour molecules content that could easily be fitted by the Langmuir–Henry-clustering model. Such sensors are thus expected to be good candidates for implementation in electronic noses.

Polyaniline nanoparticle–carbon nanotube hybrid network vapour sensors with switchable chemo-electrical polarity

Chemo-resistive sensors were prepared from monodisperse poly(aniline) nanoparticles (PaniNP) synthesized via oxidative dispersion polymerization. Poly(styrene sulfonic acid) (PSSA) was used as the stabilizer and dopant agent. PaniNP transducers were assembled by spraying layer by layer a solution containing different concentrations of PaniNP and multi-wall carbon nanotubes (MWNT) onto interdigitated electrodes. This process led to stable sensors with reproducible responses upon chemical cycling. Chemo-electrical properties of these sensors have been investigated in sequential flows of pure nitrogen and nitrogen saturated with a set of volatile organic compounds (VOC). Interestingly the sensing mode of PaniNP transducers (the NVC or PVC effect) can be switched simply by increasing PaniNP content or by the addition of only 0.5% of MWNT to reach a resistance lower than 150 Omega. Due to their original conducting architecture well imaged by atomic force microscopy (AFM), i.e. a double percolated conductive network, PaniNP-MWNT hybrids present both higher sensitivity and selectivity than other formulations, demonstrating a positive synergy. Mechanisms are proposed to describe the original chemo-electrical behaviours of PaniNP-based sensors and explain the origin of their selectivity and sensing principle. These features make them attractive to be integrated in e-noses.

Conductive polymer composites with double percolated architecture of carbon nanoparticles and ceramic microparticles for high heat dissipation and sharp PTC switching

In classical self-limiting heating devices where conductive polymer composites (CPC) are used, one of the main problems to solve is the stability of properties with time. Different strategies are proposed to stabilize the morphologies during the structuring of these heterogeneous materials. Some of them are well known in the use of co-continuous polymer blends or confinement but the interest of this work is to combine different structuring methods such as volume exclusion, adsorption and multiple percolations to achieve original properties. In fact the CPC developed exhibit enhanced heat dissipation and thermal stability (up to 180 °C), independent adjustability of electrical and thermal conductivity, and a sharp and large amplitude PTC effect. These original results were obtained with a co-continuous structure associating a thermally conductive polymer phase (syndiotactic poly(styrene) (sPS) filled with aluminum oxide (Al2O3) or boron nitride (BN)) with an electrically conductive polymer phase (high-density poly(ethylene)) (hdPE) filled with carbon nanoparticles (CNP) in appropriate proportions.

Sensing Skin for Strain Monitoring Made of PC–CNT Conductive Polymer Nanocomposite Sprayed Layer by Layer

Sensing skins about 1.5 μm thick made of 40 nanolayers of conductive polymer nanocomposites (CPC) were sprayed layer by layer (sLbL) directly on a PET woven textile to demonstrate their versatility to monitor the deformation of a flexible, rigid and rough substrate such as a commercial boat sail. CPC sensing skins were developed by structuring a 3D carbon nanotubes network into three kinds of amorphous thermoplastic matrices (PMMA, aPS, PC). Adjustable parameters such as the thickness (number of sprayed layers) and the initial resistance of CPC transducers (CNT content relatively to percolation threshold) enabled to tailor both sensitivity and stability of the piezo-resistive responses, so that it was possible to monitor the strain evolution in the elastic domain and damage accumulation over this limit. Polymer matrices were selected after calculation of their χ Flory-Huggins parameters to evaluate their interactions with the PET substrate and solvent of dispersion, and after the comparison of their stress/strain characteristics, particularly their elastic limit. PC-1%CNT was found to be the best candidate satisfying both chemical and physical criteria. Finally, the exponential evolution of the piezo-resistive response of CPC sensing skins on a wide range of deformation (until breakage at ε = 27%), was well fitted with a model based on quantum tunnelling conduction inducing an exponential evolution of resistance with variations of CNT/CNT junction gap from 0.5 to 0.625 nm.

Fine control of carbon nanotubes–polyelectrolyte sensors sensitivity by electrostatic layer by layer assembly (eLbL) for the detection of volatile organic compounds (VOC)

Volatile organic compounds (VOC) sensors have recently extended their field of application to medical area as they are considered as biomarkers in anticipated diagnosis of diseases such as lung cancer by breath analysis. Conductive polymer nanocomposites (CPC) have already proved their interest to fabricate sensors for the design of electronic noses (e-noses) but, for the first time to our knowledge, the present study is showing that electrostatic layer by layer assembly (eLbL) is bringing an interesting input to tailor the sensitivity of carbon nanotubes (CNT)-polyelectrolyte sensors. By this technique transducers are progressively built in 3D alternating dipping into sodium deoxycholate (DOC)-stabilized SWNT and poly(diallyldimethyl-ammonium chloride) [PDDA] solutions, respectively anionic and cationic. The precise control of transducers thicknesses (between 5 and 40nm) resulting from this process allows a fine tuning of multilayer films resistance (between 50 and 2kΩ) and thus of their sensitivity to VOC. Interestingly the surfactant used to disperse CNT into water, DOC is also found to enhance CNT sensitivity to vapors so is it for the polyelectrolyte PDDA. Finally it is found that transducers with 16 bilayers of PDDA/DOC-CNT provide optimum chemo-resistive properties for the detection and discrimination of the eight vapors studied (chloroform, acetone, ethanol, water, toluene, dichloromethane, tetrahydrofuran and methanol).

Controlled conductive junction gap for chitosan–carbon nanotube quantum resistive vapour sensors

The sensitivity of quantum resistive vapour sensors depends exponentially on the average gap between two conductive nanofillers at conductive junctions. The influence of this parameter on the chemo-resistive properties of chitosan (Chit)–carbon nanotubes (CNTs) has been investigated by modifying the processing conditions used to build hierarchically structured Conductive Polymer nanoComposite (CPC) transducers. Three vapour sensors assembled via spray layer by layer (sLbL) deposition: multiwall carbon nanotubes (CNTs), chitosan functionalized CNTs (Chit-f-CNTs) and chitosan embedded CNTs (Chit-CNTs) were deposited onto interdigitated electrodes and submitted to a typical set of volatile organic compounds (VOCs). Three model conducting architectures have been derived from these CPCs in which CNT/CNT junctions were respectively: in close contact (small gap), random contact (distribution of gap) and constant gap (controlled by the sheathing of CNT by crosslinked chitosan coating). The different CPC morphologies have been visualized by atomic force microscopy (AFM) and noncovalent bonding of chitosan on CNT was confirmed by UV spectra. Among the three CPC sensors exposed to water, methanol and toluene vapours, Chit-f-CNT was the most sensitive confirming the interest of controlling the gap between CNTs in the design of CPC transducers. Moreover a strong affinity of chitosan based sensors to water (and to a lesser extent to other polar vapours such as alcohols) was shown. It was taken benefit from this property to enhance the discrimination ability towards water vapour of a set of sensors assembled into an e-nose after the treatment of signals by principal component analysis (PCA).

Graphene Oxide-Assisted Liquid Phase Exfoliation of Graphite into Graphene for Highly Conductive Film and Electromechanical Sensors

Here, we report a new method to prepare graphene from graphite by the liquid phase exfoliation process with sonication using graphene oxide (GO) as a dispersant. It was found that GO nanosheets act a as surfactant to the mediated exfoliation of graphite into a GO-adsorbed graphene complex in the aqueous solution, from which graphene was separated by an additional process. The preparation of isolated graphene from a single to a few layers is routinely achieved with an exfoliation yield of up to higher than 40% from the initial graphite material. The prepared graphene sheets showed a high quality (C/O ∼ 21.5), low defect (ID/IG ∼ 0.12), and high conductivity (6.2 × 10(4) S/m). Moreover, the large lateral size ranging from 5 to 10 μm of graphene, which is believed to be due to the shielding effect of GO avoiding damage under ultrasonic jets and cavitation formed by the sonication process. The thin graphene film prepared by the spray-coating technique showed a sheet resistance of 668 Ω/sq with a transmittance of 80% at 550 nm after annealing at 350 °C for 3 h. The transparent electrode was even greater with the resistance only 66.02 Ω when graphene is deposited on an interdigitated electrode (1 mm gap). Finally, a flexible sensor based on a graphene spray-coating polydimethylsiloxane (PDMS) is demonstrated showing excellent performance working under human touch pressure (<10 kPa). The graphene prepared by this method has some distinct properties showing it as a promising material for applications in electronics including thin film coatings, transparent electrodes, wearable electronics, human monitoring sensors, and RFID tags.

Ultrasensitive QRS made by supramolecular assembly of functionalized cyclodextrins and graphene for the detection of lung cancer VOC biomarkers

A novel electronic nose system comprising functionalized β-cyclodextrin wrapped reduced graphene oxide (RGO) sensors with distinct ability of discrimination of a set of volatile organic compounds has been developed. Non-covalent modification of chemically functionalized cyclodextrin with RGO is carried out by using pyrene adamantane as a linker wherever necessary, in order to construct a supramolecular assembly. The chemical functionality on cyclodextrin is varied utilising the principle of selective chemical modification of cyclodextrin. In the present study, the combined benefits of the host-guest inclusion complex formation ability and tunable chemical functionality of cyclodextrin, as well as the high surface area and electrical conductivity of graphene, are utilized for the development of a set of highly selective quantum resistive chemical vapour sensors (QRS), which can be assembled in an electronic nose.