Jean Gamby

A flexible sample introduction method for polymer microfluidic chips using a push/pull pressure pump

A push/pull sample introduction method based on push/pull pressure flow for microfluidic systems (cross, double T and multichannel structures) is presented. This leads to well-defined and controllable sample plugs even when dealing with long channels. By tuning the relative push/pull pressure, it is shown that the size of the sample plug can effectively be controlled. Good signal reproducibility upon continued sample introduction and subsequent chip electrophoresis employing fluorescence detection is demonstrated for different chip geometries (i.e. short channels and long channels). Since the performance of the method is relatively insensitive to chip geometry, it is particularly useful for polymeric prototype microchips as tedious optimization is not required. Furthermore, the push/pull sample introduction is extended to multichannel chips thus demonstrating the possibilities of applying the methodology for realizing single chip high throughput sample analysis.

Polycarbonate microchannel network with carpet of Gold NanoWires as SERS-active device

A polycarbonate (PC) microchannel network supporting gold nanowires was developed to be a SERS-active microchip. Observations of large increases in a Raman cross-section, allowed us to collect vibrational signatures which are not easily detectable by Raman techniques due to the high fluorescence level of bare PC. Compared to other SERS experiments, this study relies on the use of dielectric polymer/metal surfaces which are well defined at microscale and nanoscale levels. This device seems a promising tool for sensing the adsorption of biomolecules.

Rotating disk electrodes to assess river biofilm thickness and elasticity

The present study examined the relevance of an electrochemical method based on a rotating disk electrode (RDE) to assess river biofilm thickness and elasticity. An in situ colonisation experiment in the River Garonne (France) in August 2009 sought to obtain natural river biofilms exhibiting differentiated architecture. A constricted pipe providing two contrasted flow conditions (about 0.1 and 0.45 m s(-1) in inflow and constricted sections respectively) and containing 24 RDE was immersed in the river for 21 days. Biofilm thickness and elasticity were quantified using an electrochemical assay on 7 and 21 days old RDE-grown biofilms (t(7) and t(21), respectively). Biofilm thickness was affected by colonisation length and flow conditions and ranged from 36 ± 15 μm (mean ± standard deviation, n = 6) in the fast flow section at t(7) to 340 ± 140 μm (n = 3) in the slow flow section at t(21). Comparing the electrochemical signal to stereomicroscopic estimates of biofilms thickness indicated that the method consistently allowed (i) to detect early biofilm colonisation in the river and (ii) to measure biofilm thickness of up to a few hundred μm. Biofilm elasticity, i.e. biofilm squeeze by hydrodynamic constraint, was significantly higher in the slow (1300 ± 480 μm rpm(1/2), n = 8) than in the fast flow sections (790 ± 350 μm rpm(1/2), n = 11). Diatom and bacterial density, and biofilm-covered RDE surface analyses (i) confirmed that microbial accrual resulted in biofilm formation on the RDE surface, and (ii) indicated that thickness and elasticity represent useful integrative parameters of biofilm architecture that could be measured on natural river assemblages using the proposed electrochemical method.

Electroacoustic Polymer Microchip as an Alternative to Quartz Crystal Microbalance for Biosensor Development

Laser photoablation of poly(ethylene terephthalate) (PET), a flexible dielectric organic polymer, was used to design an acoustic miniaturized DNA biosensor. The microchip device includes a 100-microm-thick PET layer, with two microband electrodes patterned in photoablated microchannels on one side and a depressed photoablated disk decorated by gold sputtered layer on the other side. Upon application of an electric signal between the two electrodes, an electroacoustic resonance phenomenon at approximately 30 MHz was established through the microelectrodes/PET/ gold layer interface. The electroacoustic resonance response was fitted with a series RLC motional arm in parallel with a static Co arm of a Buttlerworth-Van Dyke equivalent circuit: admittance spectra recorded after successive cycles of DNA hybridization on the gold surface showed reproducible changes on R, L, and C parameters. The same hybridizations runs were performed concomitantly on a 27-MHz (9 MHz, third overtone) quartz crystal microbalance in order to validate the PET device developed for bioanalysis applications. The electroacoustic PET device, approximately 100 times smaller than a microbalance quartz crystal, is interesting for the large-scale integration of acoustic sensors in biochips.

Nanomosaic Network for the Detection of Proteins Without Direct Electrical Contact

A nanomosaic network of metallic nanoparticles for the detection of ultralow concentrations of proteins is reported, which uses two planar microelectrodes embedded in a microchip that permit generation of capacitive coupling to the nanomosaic system without the need for direct electrical contact with the channel. By tailoring the microchannel surface using a sandwich configuration of polyethylene terephthalate/gold nanoparticles/poly(L-lysine), the surface charge can be modified following biomolecular interactions and monitored using a noncontact admittance technique. This nanodevice system behaves like a tunable capacitor and can be employed for the detection of any kind of molecule. The femtomolar detection of an anionic protein, such as beta-lactoglobulin in phosphate-buffered saline medium, is taken as an example.

Molecular Microfluidic Bioanalysis: Recent Progress in Preconcentration, Separation, and Detection

This chapter reviews the state-of-art of microfluidic devices for molecular bioanalysis with a focus on the key functionalities that have to be successfully integrated, such as preconcen‐ tration, separation, signal amplification, and detection. The first part focuses on both pas‐ sive and electrophoretic separation/sorting methods, whereas the second part is devoted to miniaturized biosensors that are integrated in the last stage of the fluidic device.

Overview of Materials for Microfluidic Applications

For each material dedicated to microfluidic applications, inherent microfabrication and specific physico‐chemical properties are key concerns and play a dominating role in further microfluidic operability. From the first generation of inorganic glass, silicon and ceramics microfluidic devices materials, to diversely competitive polymers alternatives such as soft and rigid thermoset and thermoplastics materials, to finally various paper, biodegradable and hydrogel materials; this chapter will review their advantages and drawbacks regarding their microfabrication perspectives at both research and industrial scale. The chapter will also address, the evolution of the materials used for fabricating microfluidic chips, and will discuss the application‐oriented pros and cons regarding especially their critical strategies and properties for devices assembly and biocompati‐ bility, as well their potential for downstream biochemical surface modification are presented.