Ji-Youn Seo

Incorporation of rubidium cations into perovskite solar cells improves photovoltaic performance

Improving the stability of perovskite solar cells Inorganic-organic perovskite solar cells have poor long-term stability because ultraviolet light and humidity degrade these materials. Bella et al. show that coating the cells with a water-proof fluorinated polymer that contains pigments to absorb ultraviolet light and re-emit it in the visible range can boost cell efficiency and limit photodegradation. The performance and stability of inorganic-organic perovskite solar cells are also limited by the size of the cations required for forming a correct lattice. Saliba et al. show that the rubidium cation, which is too small to form a perovskite by itself, can form a lattice with cesium and organic cations. Solar cells based on these materials have efficiencies exceeding 20% for over 500 hours if given environmental protection by a polymer coating. Science, this issue pp. 203 and 206 The seemingly too small rubidium cation was successfully integrated into perovskite solar cells. All of the cations currently used in perovskite solar cells abide by the tolerance factor for incorporation into the lattice. We show that the small and oxidation-stable rubidium cation (Rb+) can be embedded into a “cation cascade” to create perovskite materials with excellent material properties. We achieved stabilized efficiencies of up to 21.6% (average value, 20.2%) on small areas (and a stabilized 19.0% on a cell 0.5 square centimeters in area) as well as an electroluminescence of 3.8%. The open-circuit voltage of 1.24 volts at a band gap of 1.63 electron volts leads to a loss in potential of 0.39 volts, versus 0.4 volts for commercial silicon cells. Polymer-coated cells maintained 95% of their initial performance at 85°C for 500 hours under full illumination and maximum power point tracking.

Enhancing Efficiency of Perovskite Solar Cells via N-doped Graphene: Crystal Modification and Surface Passivation.

Controlling the morphology and surface passivation in perovskite solar cells is paramount in obtaining optimal optoelectronic properties. This study incorporates N-doped graphene nanosheets in the perovskite layer, which simultaneously induces an improved morphology and surface passivation at the perovskite/spiro interface, resulting in enhancement in all photovoltaic parameters.

Enhanced Charge Collection with Passivation Layers in Perovskite Solar Cells

The Al2 O3 passivation layer is beneficial for mesoporous TiO2 -based perovskite solar cells when it is deposited selectively on the compact TiO2 surface. Such a passivation layer suppressing surface recombination can be formed by thermal decomposition of the perovskite layer during post-annealing.

The effect of illumination on the formation of metal halide perovskite films

Optimizing the morphology of metal halide perovskite films is an important way to improve the performance of solar cells when these materials are used as light harvesters, because film homogeneity is correlated with photovoltaic performance. Many device architectures and processing techniques have been explored with the aim of achieving high-performance devices, including single-step deposition, sequential deposition and anti-solvent methods. Earlier studies have looked at the influence of reaction conditions on film quality, such as the concentration of the reactants and the reaction temperature. However, the precise mechanism of the reaction and the main factors that govern it are poorly understood. The consequent lack of control is the main reason for the large variability observed in perovskite morphology and the related solar-cell performance. Here we show that light has a strong influence on the rate of perovskite formation and on film morphology in both of the main deposition methods currently used: sequential deposition and the anti-solvent method. We study the reaction of a metal halide (lead iodide) with an organic compound (methylammonium iodide) using confocal laser scanning fluorescence microscopy and scanning electron microscopy. The lead iodide crystallizes before the intercalation of methylammonium iodide commences, producing the methylammonium lead iodide perovskite. We find that the formation of perovskite via such a sequential deposition is much accelerated by light. The influence of light on morphology is reflected in a doubling of solar-cell efficiency. Conversely, using the anti-solvent method to form methyl ammonium lead iodide perovskite in a single step from the same starting materials, we find that the best photovoltaic performance is obtained when films are produced in the dark. The discovery of light-activated crystallization not only identifies a previously unknown source of variability in opto-electronic properties, but also opens up new ways of tuning morphology and structuring perovskites for various applications.

Room‐Temperature Formation of Highly Crystalline Multication Perovskites for Efficient, Low‐Cost Solar Cells

A room-temperature perovskite material yielding a power conversion efficiency of 18.1% (stabilized at 17.7%) is demonstrated by judicious selection of cations. Both cesium and methylammonium are necessary for room-temperature formamidinium-based perovskite to obtain the photoactive crystalline perovskite phase and high-quality crystals. This room-temperature-made perovskite material shows great potential for low-cost, large-scale manufacturing such as roll-to-roll processing.

Cesium-containing triple cation perovskite solar cells: improved stability, reproducibility and high efficiency††Electronic supplementary information (ESI) available. See DOI: 10.1039/c5ee03874jClick here for additional data file.

Todays best perovskite solar cells use a mixture of formamidinium and methylammonium as the monovalent cations. Adding cesium improves the compositions greatly.

Crystal engineering by eliminating weak hydrogen bonding sites in phenolic polyene nonlinear optical crystals

A new acentric polyene crystal OH3 with a large macroscopic second-order optical nonlinearity with optimal chromophore orientation for electro-optics and THz-wave applications has been developed by crystal engineering, eliminating weak CH⋯NC hydrogen-bonding sites, but still retaining strong OH⋯NC hydrogen-bonding sites of the analogue OH1 crystals.

Ultrafast carrier phonon dynamics in NaOH-reacted graphite oxide film

NaOH-reacted graphite oxide film was prepared by decomposing epoxy groups in graphite oxide into hydroxyl and -ONa groups with NaOH solution. Ultrafast carrier dynamics of the sample were studied by time-resolved transient differential reflection (ΔR/R). The data show two exponential relaxation processes. The slow relaxation process (∼2ps) is ascribed to low energy acoustic phonon mediated scattering. The electron-phonon coupling and first-principles calculation results demonstrate that -OH and -ONa groups in the sample are strongly coupled. Thus, we attribute the fast relaxation process (∼0.17ps) to the coupling of hydroxyl and -ONa groups in the sample.

Additives, Hole Transporting Materials and Spectroscopic Methods to Characterize the Properties of Perovskite Films

The achievement of high efficiency and high stability in perovskite solar cells (PSCs) requires optimal selection and evaluation of the various components. After a brief introduction to the perovskite materials and their historical evolution, the first part is devoted to the hole transporting material (HTM), between photoelectrode and dark counter electrode. The basic requirements for an efficient HTM are stated. Subsequently, the most used HTM, spiro-OMeTAD, is compared to alternative HTMs, both small-molecule size species and electronically conducting polymers. The second part is devoted to additives related to the performance of the perovskite light-absorbing material itself. These are related either to the modification of the composition of the material itself or to the optimization of the morphology during the perovskite preparation stage, and their effect is in the enhancement of the power conversion efficiency, the long-term stability, or the reproducibility of the properties of the PSCs. Finally, a number of spectroscopic methods based on the UV-Vis part of the electromagnetic spectrum useful for characterizing the different perovskite material types are described in the last part of this review.

Novel p-dopant toward highly efficient and stable perovskite solar cells

Li-TFSI is the most common p-dopant for the hole conductor spiro-MeOTAD in the normal structure (n–i–p) of perovskite solar cells (PSCs), which consistently yield the highest power conversion efficiency (PCE) albeit at the risk of lower long-term operational stability. Here we successfully replace conventional Li-TFSI with Zn-TFSI2, which not only acts as a highly effective p-dopant but also enhances considerably both the photovoltaic performance and long-term stability. The incorporation of Zn-TFSI2 as a dopant for spiro-MeOTAD leads to an increase by one order in the hole mobility compared to Li-TFSI from 3.78 × 10−3 cm2 V−1 s−1 to 3.83 × 10−2 cm2 V−1 s−1. Furthermore, the device with Zn-TFSI2 showed an 80 mV higher built-in voltage and a bigger recombination resistance than the one with Li-TFSI, which were responsible for the striking increase in both the open-circuit voltage and fill factor, leading to a stabilized PCE of 22.0% for the best cells. Remarkably, the device employing Zn-TFSI2 demonstrated superb photo-stability, showing even a 2% increase in the PCE after 600 h light soaking at the maximum power point (mpp) under full sun, while the PCE of the device with Li-TFSI decreased by 20% under the same conditions. Similarly, the device with Zn-TFSI2 showed better operational stability at 50 °C resulting in a 21% decrease in the PCE after 100 h aging at the mpp under full sun while the Li-TFSI based one showed a 55% decrease. Moreover, the Zn-TFSI2 based device was capable of effectively resisting humidity compared to the one based on Li-TFSI from shelf stability monitoring (R.H. ≥ 40%) in the dark.