Jing Hai

Characterization and mass balance of dioxin from a large-scale municipal solid waste incinerator in China

The input and output samples from existing large-scale municipal solid waste incinerator (MSWI) were collected and analyzed for polychlorinated dibenzo-р-dioxins and dibenzofurans (PCDD/Fs) in this study, aiming to evaluate PCDD/F characteristic and the corresponding mass balance through the whole system. The grate-type MSWI is equipped with semi-dry scrubber, activated carbon injection, and bag filter as air pollutant control devices (APCDs). Results showed that on the output side, the stack gas, bottom ash and fly ash presented their mean dioxin levels of 0.078 ng I-TEQ/Nm(3), 12.94 ng I-TEQ/kg and 858 ng I-TEQ/kg, respectively, and showed large similarities in congener profiles. Instead, on the input side, the municipal solid waste (MSW) presented a mean dioxin level of 15.56 ng I-TEQ/kg and a remarkable difference in congener profiles compared with those of the output. The dioxin mass balance demonstrated that the annual dioxin input value was around 5.38 g I-TEQ/yr, lower than the total output value (7.62 g I-TEQ/yr), signifying a positive dioxin balance of about 2.25 g I-TEQ/yr.

Emission, mass balance, and distribution characteristics of PCDD/Fs and heavy metals during cocombustion of sewage sludge and coal in power plants.

The emission, mass balance, and distribution characteristics of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) as well as those of heavy metals (Hg, Cd, Pb, Cr, and Cu) were investigated during the cocombustion of 5%, 10%, 15%, and 20% sewage sludge (SS) in a pulverized coal power plant. The PCDD/F emissions increased from 7.00 to 32.72 pg I-TEQ/Nm(3) as the amount of SS in the mixed fuel (MF) increased. High sulfur content and relatively low chlorine levels in MF resulted in lower PCDD/F emissions. SS exhibited a remarkable difference in congener profiles compared with flue gas, bottom ash, and fly ash. The negative dioxin mass balance indicated that the cofiring of SS with coal in power plants was not a source but a sink of dioxins. The concentrations and emission factors of heavy metals in flue gas and bottom ash, as well as fly ash, all exhibited a tendency to increase with increasing input values of heavy metals in MF. The distribution characteristics of the investigated heavy metals were primarily dependent on the evaporative properties of these metals. The availability of chlorine could alter the heavy metal distribution behavior. The emitted pollutants in the power plant were below the legal limits.

Evaluation of PCDD/Fs and metals emission from a circulating fluidized bed incinerator co-combusting sewage sludge with coal

The emission characteristics of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and heavy metals were evaluated during co-combustion of sewage sludge with coal from a circulating fluidized bed incinerator. The stack gas, slag and fly ash samples were sampled and analyzed. The gas-cleaning system consisted of electrostatic precipitators and a semi-dry scrubber. Results showed that the stack gas and fly ash exhibited mean dioxin levels of 9.4 pg I-TEQ/Nm3 and 11.65 pg I-TEQ/g, respectively, and showed great similarities in congener profiles. By contrast, the slag presented a mean dioxin level of 0.15 pg I-TEQ/g and a remarkable difference in congener profiles compared with those of the stack gas and fly ash. Co-combusting sewage sludge with coal was able to reduce PCDD/Fs emissions significantly in comparison with sewage sludge mono-combustion. The leaching levels of Hg, Pb, Cd, Ni, Cr, Cu, and As in the fly ash and slag were much lower than the limits of the environmental protection standard in China. These suggest that the co-combustion of sewage sludge and coal is an advisable treatment method from an environmental perspective.

Status and perspectives of municipal solid waste incineration in China: A comparison with developed regions

With the rapid expansion of municipal solid waste (MSW) incineration, the applicability, technical status, and future improvement of MSW incineration attract much attention in China. This paper aims to be a sensible response, with the aid of a comparison between China and some representative developed regions including the EU, the U.S., Japan, South Korea, and Taiwan area. A large number of up-to-date data and information are collected to quantitatively and impartially support the comparison, which covers a wider range of key points including spatial distribution, temporal evolution, technologies, emissions, and perspectives. Analysis results show that MSW incineration is not an outdated choice; however, policy making should prevent the potentially insufficient utilization of MSW incinerators. The structure of MSW incineration technologies is changing in China. The ratio of plants using fluidized bed is decreasing due to various realistic reasons. Decision-makers would select suitable combustion technologies by comprehensive assessments, rather than just by costs. Air pollution control systems are improved with the implementation of Chinas new emission standard. However, MSW incineration in China is currently blamed for substandard emissions. The reasons include the particular elemental compositions of Chinese MSW, the lack of operating experience, deficient fund for compliance with the emission standard, and the lack of reliable supervisory measures. Some perspectives and suggestions from both technical and managerial aspects are given for the compliance with the emission standard. This paper can provide strategic enlightenments for MSW management in China and other developing countries.

Emission characteristics of PCDD/Fs in stack gas from municipal solid waste incineration plants in Northern China

Emission characteristics including congeners profile, gas emissions and toxic equivalent concentration (TEQ) indicators of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) in 57 stack gas samples from 6 municipal solid waste incinerators (MSWIs) in Northern China were investigated by gas chromatography-high resolution mass spectrometry (HRGC-HRMS). Additionally, PCDD/Fs formation mechanisms from the MSWIs were briefly discussed. Results revealed that the concentrations and equivalent concentrations of PCDD/Fs emissions in stack gas from 6 MSWIs were in the range of 0.11-2.53 ng Nm-3 and 0.007-0.059 ng TEQ Nm-3, respectively. The emission factors of PCDD/Fs from 6 MSWIs varied from 0.027 to 0.225 μg I-TEQ tonne-1, with a mean value of 0.17 μg I-TEQ tonne-1 waste, which was estimated to an annual emission of 234.96 mg I-TEQ of PCDD/Fs from 6 MSWIs to the atmosphere. O8CDD, O8CDF and 1,2,3,4,6,7,8-H7CDD were the indicatory compounds of PCDD/Fs to apportion the sources of PCDD/Fs in environmental medium especially in ambient environment of MSWIs. 1,2,3,7,8,9-H6CDF and 1,2,3,4,7,8-H6CDF can be used as TEQ indicators for monitoring PCDD/Fs emission. Based on the positive matrix factorization (PMF) model, eight factors were extracted by the PMF analysis. Formation of low-chlorinated PCDDs (1,2,3,7,8-P5CDD, 1,2,3,4,7,8-H6CDD, 1,2,3,6,7,8-H6CDD and 1,2,3,7,8,9-H6CDD) possessed strong correlation, and the chlorophenols maybe the important precursors of low-chlorinated PCDDs, which were generated within the low chlorinated content. Penta- and hexa-PCDFs formation in stack gas from MSWI may block catalytic sites for PCDFs formation from carbon. Meanwhile, possible formation mechanisms of high-chlorinated PCDDs (hepta- and octa-PCDDs) and high-chlorinated PCDFs (hepta- and octa-PCDFs) were respectively dependent.

Emission characteristics of toxic pollutants from an updraft fixed bed gasifier for disposing rural domestic solid waste

Gasification has gained advantage as an effective way to dispose domestic solid waste in mountainous rural of China. However, its toxic emissions such as PCDD/Fs and heavy metals, as well as their potential environmental risks, were not well studied in engineering application. In this study, an updraft fixed bed gasifier was investigated by field sampling analysis. Results showed that low toxic emissions (dust, SO2, NOx, HCl, CO, H2S, NH3, PCDD/Fs and heavy metals) in the flue gas were achieved when the rural solid waste was used as feedstock. The mass distribution of heavy metals showed that 94.00% of Pb, 80.45% of Cu, 78.00% of Cd, 77.31% of Cr, and 76.25% of As were remained in residual, whereas 86.58% of Hg was found in flue gas. The content of PCDD/Fs in the flue gas was 0.103 ngI-TEQ·Nm−3, and the total emission factor of PCDD/Fs from the gasifier was 50.04 μgI-TEQ·t-waste−1, among which only 0.04 μgI-TEQ·t-waste−1 was found in the flue gas. The total output of PCDD/Fs was1.89 times as high as input, indicting the updraft fixed bed gasifier increased emission of PCDD/Fs during the treatment domestic solid waste. In addition, the distribution characteristics of PCDD/Fs congeners reflected that PCDD/Fs was mainly generated in the gasification process rather than the stage of flue gas cleaning, suggesting the importance to effectively control the generation of PCDD/Fs within the gasifier chamber in order to obtain a low PCDD/Fs emission level.

Polychlorinated Dibenzo-P-Dioxins and Dibenzofurans from a Grate-Type Municipal Solid Waste Incinerator in China

The emission characteristics of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) were evaluated from a grate-type municipal solid waste incinerator (MSWI). The stack flue gas, fly ash and bottom ash samples were sampled and analyzed. Results indicated that the flue gas, fly ash and bottom ash presented their mean dioxin levels of 0.0723 ng I-TEQ/Nm3, 0.614 ng I-TEQ/g and 13.33 ng I-TEQ/kg respectively. The PCDD/Fs congener patterns, in flue gas, fly ash and bottom ash, showed large similarities in both concentration and I-TEQ profiles. The de novo synthesis plays a dominant role in the low-temperature post-combustion zone.

Preparation and Performance of RTV Coating for Anti-Pollution Flashover with Superhydrophobicity by Filling CaCO3/SiO2 Composite Particles into Silicone Rubber

Room temperature vulcanizing (RTV) silicone rubber coating with superhydrophobicity for anti-pollution flashover is prepared by filling silica-encapsulated calcium carbonate particles (CaCO3/SiO2 composite particles) into polydimethylsiloxane (PDMS) rubber. Two-step spraying technology is applied for fabricating the superhydrophobic RTV coating film on outdoor insulators. The primary spray coating provides basically the strong adhesion and certain hydrophobicity, and the second one produces the appropriate roughness structure and further enhances the superhydrophobicity. The water contact angle on the prepared RTV coating film is 165°and the sliding (rolling) angle of water droplet is about 5°, allowing water droplets to move easily on the coating surface and give self-cleaning function of the RTV coated insulator surface. The flashover voltage of insulators with superhydrophobic RTV coating is 29.95 kV, quite higher than that of insulators with common RTV coating (23.29) and that without RTV coating (11.34 kV).