Jonathan D. Zuegel

High-Energy Petawatt Capability for the Omega Laser

The 60-beam Omega laser system at the University of Rochesters Laboratory for Laser Energetics (LLE) has been a workhorse on the frontier of laser fusion and high-energy-density physics for more than a decade. LLE scientists are currently extending the performance of this unique, direct-drive laser system by adding high-energy petawatt capabilities.

High-conversion-efficiency optical parametric chirped-pulse amplification system using spatiotemporally shaped pump pulses

High-conversion-efficiency, high-stability optical parametric chirped-pulse amplification is demonstrated with a spatiotemporally shaped pump laser system. Broadband 5-mJ pulses are produced at a 5-Hz repetition rate with a pump-to-signal conversion efficiency of 29% and energy stability better than 2% rms. To our knowledge this is the highest conversion efficiency and stability achieved in an optical parametric chirped-pulse amplification system.

Direct-drive inertial confinement fusion: A review

The direct-drive, laser-based approach to inertial confinement fusion (ICF) is reviewed from its inception following the demonstration of the first laser to its implementation on the present generation of high-power lasers. The review focuses on the evolution of scientific understanding gained from target-physics experiments in many areas, identifying problems that were demonstrated and the solutions implemented. The review starts with the basic understanding of laser–plasma interactions that was obtained before the declassification of laser-induced compression in the early 1970s and continues with the compression experiments using infrared lasers in the late 1970s that produced thermonuclear neutrons. The problem of suprathermal electrons and the target preheat that they caused, associated with the infrared laser wavelength, led to lasers being built after 1980 to operate at shorter wavelengths, especially 0.35 μm—the third harmonic of the Nd:glass laser—and 0.248 μm (the KrF gas laser). The main physics areas relevant to direct drive are reviewed. The primary absorption mechanism at short wavelengths is classical inverse bremsstrahlung. Nonuniformities imprinted on the target by laser irradiation have been addressed by the development of a number of beam-smoothing techniques and imprint-mitigation strategies. The effects of hydrodynamic instabilities are mitigated by a combination of imprint reduction and target designs that minimize the instability growth rates. Several coronal plasma physics processes are reviewed. The two-plasmon–decay instability, stimulated Brillouin scattering (together with cross-beam energy transfer), and (possibly) stimulated Raman scattering are identified as potential concerns, placing constraints on the laser intensities used in target designs, while other processes (self-focusing and filamentation, the parametric decay instability, and magnetic fields), once considered important, are now of lesser concern for mainline direct-drive target concepts. Filamentation is largely suppressed by beam smoothing. Thermal transport modeling, important to the interpretation of experiments and to target design, has been found to be nonlocal in nature. Advances in shock timing and equation-of-state measurements relevant to direct-drive ICF are reported. Room-temperature implosions have provided an increased understanding of the importance of stability and uniformity. The evolution of cryogenic implosion capabilities, leading to an extensive series carried out on the 60-beam OMEGA laser [Boehly et al., Opt. Commun. 133, 495 (1997)], is reviewed together with major advances in cryogenic target formation. A polar-drive concept has been developed that will enable direct-drive–ignition experiments to be performed on the National Ignition Facility [Haynam et al., Appl. Opt. 46(16), 3276 (2007)]. The advantages offered by the alternative approaches of fast ignition and shock ignition and the issues associated with these concepts are described. The lessons learned from target-physics and implosion experiments are taken into account in ignition and high-gain target designs for laser wavelengths of 1/3 μm and 1/4 μm. Substantial advances in direct-drive inertial fusion reactor concepts are reviewed. Overall, the progress in scientific understanding over the past five decades has been enormous, to the point that inertial fusion energy using direct drive shows significant promise as a future environmentally attractive energy source.

5?Hz, >250?mJ optical parametric chirped-pulse amplifier at 1053?nm

A 250 mJ, 5 Hz repetition rate optical parametric chirped-pulse amplifier with near-Fourier-transform-limited, 430 fs pulses and a beam that can be focused to near the diffraction limit is demonstrated. A pump laser with engineered spatial and temporal profiles allows an overall pump-to-signal conversion efficiency of 34% to be achieved.

High-contrast optical-parametric amplifier as a front end of high-power laser systems

A high-contrast preamplifier based on optical-parametric amplification with a short pump pulse is demonstrated. A gain larger than 10(5) and measurement-limited contrast higher than 10(11) are obtained over a large temporal range extending within less than 10 ps of the peak of the pulse, because of the high instantaneous parametric gain provided by a short pump pulse in a nonlinear crystal. The energy gain and high contrast of this preamplifier make it a good seed source for high-power laser systems.

Distributed Waveform Generator: A New Circuit Technique for Ultra-Wideband Pulse Generation, Shaping and Modulation

A new circuit technique, the distributed waveform generator (DWG), is proposed for low-power ultra-wideband pulse generation, shaping and modulation. It time-interleaves multiple impulse generators, and uses distributed circuit techniques to combine generated wideband impulses. Built-in pulse shaping can be realized by programming the delay and amplitude of each impulse similar to an FIR filter. Pulse modulation schemes such as on-off keying (OOK) and pulse position modulation (PPM) can be easily applied in this architecture. Two DWG circuit prototypes were implemented in a standard 0.18 mum digital CMOS technology to demonstrate its advantages. A 10-tap, 10 GSample/s, single-polarity DWG prototype achieves a pulse rate of 1 GHz while consuming 50 mW, and demonstrates OOK modulation using 16 Mb/s PRBS data. A 10-tap, 10 GSample/s, dual-polarity DWG prototype was developed to generate UWB pulses compliant with the transmit power emission mask. Based on the latter DWG design, a reconfigurable impulse radio UWB (IR-UWB) transmitter prototype was implemented. The transmitters pulse rate can be varied from 16 MHz range up to 2.5 GHz. The bandwidth of generated UWB pulses is also variable, and was measured up to 6 GHz (- 10 dB bandwidth). Both OOK and PPM modulation schemes are successfully demonstrated using 32 Mb/s PRBS data. The IR-UWB transmitter achieves a measured energy efficiency of 45 pJ/pulse, independent of pulse rate.

Design and analysis of binary beam shapers using error diffusion

An error diffusion algorithm is used to design binary pixelated beam shapers. Beam shapers based on pixels with transmission equal either to 0 or 1 can be synthesized with this deterministic algorithm to provide continuous intensity shaping after Fourier filtering. The capabilities of these shapers are studied for high-power lasers. A particular emphasis is placed on the influence of the feature size on the performance of the designed shapers, and it is shown that the transmission degradation is highly predictable for this algorithm. Simulations demonstrating the possibility of precompensating for feature size when designing intensity shapers are presented.

Independent phase and amplitude control of a laser beam by use of a single-phase-only spatial light modulator

A phase-only spatial light modulator is used in conjunction with a spatial filter to provide independent control of the phase and amplitude of a laser beam. Continuous amplitude modulation of the beam is achieved with a resolution relevant to beam shaping of high-energy laser beams. Amplitude beam correction in a closed loop is demonstrated.

Core performance and mix in direct-drive spherical implosions with high uniformity

The performance of gas-filled, plastic-shell implosions has significantly improved with advances in on-target uniformity on the 60-beam OMEGA laser system [T. R. Boehly, D. L. Brown, R. S. Craxton et al., Opt. Commun. 133, 495 (1997)]. Polarization smoothing (PS) with birefringent wedges and 1-THz-bandwidth smoothing by spectral dispersion (SSD) have been installed on OMEGA. The beam-to-beam power imbalance is ⩽5% rms. Implosions of 20-μm-thick CH shells (15 atm fill) using full beam smoothing (1-THz SSD and PS) have primary neutron yields and fuel areal densities that are ∼70% larger than those driven with 0.35-THz SSD without PS. They also produce ∼35% of the predicted one-dimensional neutron yield. The results described here suggest that individual-beam nonuniformity is no longer the primary cause of nonideal target performance. A highly constrained model of the core conditions and fuel–shell mix has been developed. It suggests that there is a “clean” fuel region, surrounded by a mixed region, that acc...

Design of a highly stable, high-conversion-efficiency, optical parametric chirped-pulse amplification system with good beam quality

An optical parametric chirped-pulse amplifier (OPCPA) design that provides 40% pump-to-signal conversion efficiency and over-500-mJ signal energy at 1054 nm for front-end injection into a Nd:glass amplifier chain is presented. This OPCPA system is currently being built as the prototype front end for the OMEGA EP (extended performance) laser system at the University of Rochesters Laboratory for Laser Energetics. Using a three-dimensional spatial and temporal numerical model, several design considerations necessary to achieve high conversion efficiency, good output stability, and good beam quality are discussed. The dependence of OPCPA output on the pump beams spatiotemporal shape and the relative size of seed and pump beams is described. This includes the effects of pump intensity modulation and pump-signal walk-off. The trade-off among efficiency, stability, and low output beam intensity modulation is discussed.