Josée Drillet

A criterion for the change from fast to slow regime of cementite dissolution in Fe - C- Mn steels

The present study clarifies the role of Mn in cementite on the driving force of cementite dissolution and the growth of austenite. From an experimental study, the effects of manganese composition and temperature on the cementite dissolution were shown. From a theoretical analysis based on thermodynamic and kinetics considerations, a criterion for the change from fast to slow regime of cementite dissolution was proposed. This criterion is in good agreement with the experimental results. It can be easily calculated and can define the composition and temperature ranges where the cementite dissolution is slow or fast.

Nanometric Scale Investigation of Phase Transformations in Advanced Steels for Automotive Application

The current trend toward producing lighter vehicles in the automotive industry is driven by the need to conform to the new exhaust emission control regulations. This objective presents a challenge to steel manufacturers. The difficulty lies in designing new alloys with an optimum strength/formability/cost balance for the various components. Here, the key to success lies in controlling the steel microstructure and especially the phase transformations at the smallest possible scale. Among the different alloying elements, light elements such as carbon and boron are of prime importance due to their major effects on the kinetics of phase transformations. Characterization tools combining high spatial and analytical resolution such as secondary ion mass spectrometry (SIMS) and field emission gun-transmission electron microscopy (TEM) were used. In this article, the examples presented are as follows. (1) Boron segregation and precipitation effects to control hardenability in martensitic steels. (2) Local carbon distribution in advanced high-strength steels, with a specific emphasis on martensite tempering. Links have been established between the boron and carbon distribution and the formability.

Combined Effect of Heating Rate and Microalloying Elements on Recrystallization During Annealing of Dual-Phase Steels

Adjusting ferrite recrystallization kinetics during annealing is a way to control the final microstructure and thus the mechanical properties of advanced cold-rolled high-strength steels. Two strategies are commonly used for this purpose: adjusting heating rates and/or adding microalloying elements. The present work investigates the effect of heating rate and microalloying elements Ti, Nb, and Mo on recrystallization kinetics during annealing in various cold-rolled Dual-Phase steel grades. The use of combined experimental and modeling approaches allows a deeper understanding of the separate influence of heating rate and the addition of microalloying elements. The comparative effect of Ti, Nb, and Mo as solute elements and as precipitates on ferrite recrystallization is also clarified. It is shown that solute drag has the largest delaying effect on recrystallization in the present case and that the order of solute drag effectiveness of microalloying elements is Nb > Mo > Ti.

Influence of Microalloying Elements Ti and Nb on Recrystallization during Annealing of Advanced High-Strength Steels

Microalloying elements Ti and Nb are commonly added to high-strength Dual Phase steels as they can provide efficient means for additional strengthening due to grain refinement and precipitation strengthening mechanisms. In the form of solute elements or as fine carbonitride precipitates, Ti and Nb are also expected to have a significant effect on the microstructural changes during annealing and especially on recrystallization kinetics. The present work investigates the influence of microalloying elements Ti and Nb on recrystallization in various cold-rolled Dual Phase steel grades with the same initial microstructure but different microalloying contents. Using complementary experimental and modeling approaches makes it possible to give some clarifications regarding both the nature of this effect and the comparative efficiency of Ti and Nb on delaying recrystallization. It is shown that niobium is the most efficient micro-alloying element to impede recrystallization and that the predominant effect is solute drag.

Influence of Heating Rate on Ferrite Recrystallization and Austenite Formation in Cold-Rolled Microalloyed Dual-Phase Steels

Compared with other dual-phase (DP) steels, initial microstructures of cold-rolled martensite-ferrite have scarcely been investigated, even though they represent a promising industrial alternative to conventional ferrite-pearlite cold-rolled microstructures. In this study, the influence of the heating rate (over the range of 1 to 10 K/s) on the development of microstructures in a microalloyed DP steel is investigated; this includes the tempering of martensite, precipitation of microalloying elements, recrystallization, and austenite formation. This study points out the influence of the degree of ferrite recrystallization prior to the austenite formation, as well as the importance of the cementite distribution. A low heating rate giving a high degree of recrystallization, leads to the formation of coarse austenite grains that are homogenously distributed in the ferrite matrix. However, a high heating rate leading to a low recrystallization degree, results in a banded-like structure with small austenite grains surrounded by large ferrite grains. A combined approach, involving relevant multiscale microstructural characterization and modeling to rationalize the effect of the coupled processes, highlights the role of the cold-worked initial microstructure, here a martensite-ferrite mixture: recrystallization and austenite formation commence in the former martensite islands before extending in the rest of the material.