Jung Heon Lee

Transparent, low-power pressure sensor matrix based on coplanar-gate graphene transistors.

A novel device architecture for preparing a transparent and low-voltage graphene pressure-sensor matrix on plastic and rubber substrates is demonstrated. The coplanar gate configuration of the graphene transistor enables a simplified procedure. The resulting devices exhibit excellent device performance, including a high transparency of ca. 80% in the visible range, a low operating voltage less than 2 V, a high pressure sensitivity of 0.12 kPa(-1) , and excellent mechanical durability over 2500 cycles.

Rapid, High‐Resolution 3D Interference Printing of Multilevel Ultralong Nanochannel Arrays for High‐Throughput Nanofluidic Transport

3D interference printing enables the single-step production of multilayered ultralong nanochannel arrays with nanoscale regularity. The superior depth-of-focus of this technique realizes a state-of-the-art nanostructure which has intensively stacked 32 layers of inch-long, horizonontal nanochannels with sub-100 nm holes in a monolithic matrix (≈15 μm). This exceptional structure can be integrated into microfluidic devices, facilitating high-flux rheological platforms using nanocapillarity.

Ultrastable-Stealth Large Gold Nanoparticles with DNA Directed Biological Functionality

The stability of gold nanoparticles (AuNPs) in biological samples is very important for their biomedical applications. Although various molecules such as polystyrenesulfonate (PSS), phosphine, DNA, and polyethylene glycol (PEG) have been used to stabilize AuNPs, it is still very difficult to stabilize large AuNPs. As a result, biomedical applications of large (30-100 nm) AuNPs are limited, even though they possess more favorable optical properties and are easier to be taken up by cells than smaller AuNPs. To overcome this limitation, we herein report a novel method of preparing large (30-100 nm) AuNPs with a high colloidal stability and facile chemical or biological functionality, via surface passivation with an amphiphilic polymer polyvinylpyrrolidone (PVP). This PVP passivation results in an extraordinary colloidal stability for 13, 30, 50, 70, and 100 nm AuNPs to be stabilized in PBS for at least 3 months. More importantly, the PVP capped AuNPs (AuNP-PVP) were also resistant to protein adsorption in the presence of serum containing media and exhibit a negligible cytotoxicity. The AuNP-PVPs functionalized with a DNA aptamer AS1411 remain biologically active, resulting in significant increase in the uptake of the AuNPs (∼12,200 AuNPs per cell) in comparison with AuNPs capped by a control DNA of the same length. The novel method developed in this study to stabilize large AuNPs with high colloidal stability and biological activity will allow much wider applications of these large AuNPs for biomedical applications, such as cellular imaging, molecular diagnosis, and targeted therapy.

pn-Heterojunction Effects of Perylene Tetracarboxylic Diimide Derivatives on Pentacene Field-Effect Transistor

We investigated the heterojunction effects of perylene tetracarboxylic diimide (PTCDI) derivatives on the pentacene-based field-effect transistors (FETs). Three PTCDI derivatives with different substituents were deposited onto pentacene layers and served as charge transfer dopants. The deposited PTCDI layer, which had a nominal thickness of a few layers, formed discontinuous patches on the pentacene layers and dramatically enhanced the hole mobility in the pentacene FET. Among the three PTCDI molecules tested, the octyl-substituted PTCDI, PTCDI-C8, provided the most efficient hole-doping characteristics (p-type) relative to the fluorophenyl-substituted PTCDIs, 4-FPEPTC and 2,4-FPEPTC. The organic heterojunction and doping characteristics were systematically investigated using atomic force microscopy, 2D grazing incidence X-ray diffraction studies, and ultraviolet photoelectron spectroscopy. PTCDI-C8, bearing octyl substituents, grew laterally on the pentacene layer (2D growth), whereas 2,4-FPEPTC, with fluorophenyl substituents, underwent 3D growth. The different growth modes resulted in different contact areas and relative orientations between the pentacene and PTCDI molecules, which significantly affected the doping efficiency of the deposited adlayer. The differences between the growth modes and the thin-film microstructures in the different PTCDI patches were attributed to a mismatch between the surface energies of the patches and the underlying pentacene layer. The film-morphology-dependent doping effects observed here offer practical guidelines for achieving more effective charge transfer doping in thin-film transistors.

Differences in DNA Probe-Mediated Aggregation Behavior of Gold Nanomaterials Based on Their Geometric Appearance

Nanoparticles are used extensively to detect nucleic acid biomarkers due to their analytical applicability and sensitivity. Systems employing the surface plasmon resonance of gold nanomaterials are overwhelmingly considered to be candidates. The aggregation of gold nanomaterials mediated by the hybridization of target DNA at the interface causes a change in the surface plasmon resonance inherent in gold nanomaterials. Such changes can be measured by spectroscopy or even visualized by the naked eye, enabling effective and positive detection. The optical properties of gold nanoparticles are affected by their shape. The geometric appearance of the nanoparticles also affects their colloidal stability and aggregation behavior. In this study, we examined the effect of the geometric appearance of gold nanomaterials on DNA-mediated aggregation behavior through comparative experiments. Experimental and theoretical methods were used concurrently to derive accurate results and to support the hypotheses. Coarse-grained molecular dynamics simulations were performed with a large-scale atomic/molecular massively parallel simulator to understand the aggregation of nanoparticles with the same surface area and various aspect ratios. As a result, we confirmed that the aggregation sensitivity of nanoparticles was affected by the shape of the contact point with the gold nanomaterials. This study demonstrates that the design of a detection system should be accompanied by an in-depth review of the morphology of the nanoparticle.