Kai Loon Chen

Aggregation kinetics of citrate and polyvinylpyrrolidone coated silver nanoparticles in monovalent and divalent electrolyte solutions.

The aggregation kinetics of silver nanoparticles (AgNPs) that were coated with two commonly used capping agents-citrate and polyvinylpyrrolidone (PVP)--were investigated. Time-resolved dynamic light scattering (DLS) was employed to measure the aggregation kinetics of the AgNPs over a range of monovalent and divalent electrolyte concentrations. The aggregation behavior of citrate-coated AgNPs in NaCl was in excellent agreement with the predictions based on Derjaguin-Landau-Verwey-Overbeek (DLVO) theory, and the Hamaker constant of citrate-coated AgNPs in aqueous solutions was derived to be 3.7 × 10(-20) J. Divalent electrolytes were more efficient in destabilizing the citrate-coated AgNPs, as indicated by the considerably lower critical coagulation concentrations (2.1 mM CaCl(2) and 2.7 mM MgCl(2) vs 47.6 mM NaCl). The PVP-coated AgNPs were significantly more stable than citrate-coated AgNPs in both NaCl and CaCl(2), which is likely due to steric repulsion imparted by the large, noncharged polymers. The addition of humic acid resulted in the adsorption of the macromolecules on both citrate- and PVP-coated AgNPs. The adsorption of humic acid induced additional electrosteric repulsion that elevated the stability of both nanoparticles in suspensions containing NaCl or low concentrations of CaCl(2). Conversely, enhanced aggregation occurred for both nanoparticles at high CaCl(2) concentrations due to interparticle bridging by humic acid aggregates.

Potential release pathways, environmental fate, and ecological risks of carbon nanotubes

Carbon nanotubes (CNTs) are currently incorporated into various consumer products, and numerous new applications and products containing CNTs are expected in the future. The potential for negative effects caused by CNT release into the environment is a prominent concern and numerous research projects have investigated possible environmental release pathways, fate, and toxicity. However, this expanding body of literature has not yet been systematically reviewed. Our objective is to critically review this literature to identify emerging trends as well as persistent knowledge gaps on these topics. Specifically, we examine the release of CNTs from polymeric products, removal in wastewater treatment systems, transport through surface and subsurface media, aggregation behaviors, interactions with soil and sediment particles, potential transformations and degradation, and their potential ecotoxicity in soil, sediment, and aquatic ecosystems. One major limitation in the current literature is quantifying CNT masses in relevant media (polymers, tissues, soils, and sediments). Important new directions include developing mechanistic models for CNT release from composites and understanding CNT transport in more complex and environmentally realistic systems such as heteroaggregation with natural colloids and transport of nanoparticles in a range of soils.

Assessing the colloidal properties of engineered nanoparticles in water: case studies from fullerene C60 nanoparticles and carbon nanotubes

Environmental context. The fate and bioavailability of engineered nanoparticles in natural aquatic systems are strongly influenced by their ability to remain dispersed in water. Consequently, understanding the colloidal properties of engineered nanoparticles through rigorous characterisation of physicochemical properties and measurements of particle stability will allow for a more accurate prediction of their environmental, health, and safety effects in aquatic systems. This review highlights some important techniques suitable for the assessment of the colloidal properties of engineered nanoparticles and discusses some recent findings obtained by using these techniques on two popular carbon-based nanoparticles, fullerene C60 and multi-walled carbon nanotubes. Abstract. The colloidal properties of engineered nanoparticles directly affect their use in a wide variety of applications and also control their environmental fate and mobility. The colloidal stability of engineered nanoparticles depends on their physicochemical properties within the given aqueous medium and is ultimately reflected in the particles’ aggregation and deposition behaviour. This review presents some of the key experimental methods that are currently used to probe colloidal properties and quantify engineered nanoparticle stability in water. Case studies from fullerene C60 nanoparticles and multi-walled carbon nanotubes illustrate how the characterisation and measurement methods are used to understand and predict nanoparticle fate in aquatic systems. Consideration of the comparisons between these two classes of carbon-based nanoparticles provides useful insights into some major current knowledge gaps while also revealing clues about needed future developments. Key issues to be resolved relate to the nature of near-range surface forces and the origins of surface charge, particularly for the reportedly unmodified or ‘pure’ carbon-based nanoparticles.

Influence of Surface Oxidation on the Aggregation and Deposition Kinetics of Multiwalled Carbon Nanotubes in Monovalent and Divalent Electrolytes

The aggregation and deposition kinetics of two multiwalled carbon nanotubes (MWNTs) with different degrees of surface oxidation are investigated using time-resolved dynamic light scattering (DLS) and quartz crystal microbalance with dissipation monitoring (QCM-D), respectively. Carboxyl groups are determined to be the predominant oxygen-containing surface functional groups for both MWNTs through X-ray photoelectron spectroscopy (XPS). The aggregation and deposition behavior of both MWNTs is in qualitative agreement with the Derjaguin-Landau-Verwey-Overbeek (DLVO) theory. The critical coagulation concentration (CCC) of the highly oxidized MWNTs (HO-MWNTs) is significantly higher than the lowly oxidized MWNTs (LO-MWNTs) in the presence of NaCl (210 and 53 mM, respectively) since HO-MWNTs have a higher surface charge density. In contrast, the aggregation inverse stability profiles of HO-MWNTs and LO-MWNTs are identical and yield comparable CCCs (0.9 and 1.0 mM, respectively) in the presence of CaCl(2). Similar to the results obtained from the aggregation study, HO-MWNTs are considerably more stable to deposition on silica surfaces compared to LO-MWNTs in the presence of NaCl. However, both MWNTs have the same propensity to undergo deposition in the presence of CaCl(2). The remarkable similarity in the aggregation and deposition kinetics of HO-MWNTs and LO-MWNTs in CaCl(2) may be due to Ca(2+) cations having a higher affinity to form complexes with adjacent carboxyl groups on HO-MWNTs than with isolated carboxyl groups on LO-MWNTs.

Heteroaggregation of multiwalled carbon nanotubes and hematite nanoparticles: rates and mechanisms.

The heteroaggregation rates of negatively charged multiwalled carbon nanotubes (CNTs) and positively charged hematite nanoparticles (HemNPs) were obtained over a broad range of nanoparticle distributions using time-resolved dynamic light scattering (DLS). Binary systems comprising CNTs and HemNPs were prepared using low ionic strength solutions to minimize the concurrent occurrence of homoaggregation. To elucidate the mechanisms of heteroaggregation, the structures of CNT-HemNP aggregates were observed using cryogenic transmission electron microscopy (cryo-TEM). An initial increase in the CNT concentration, while keeping the HemNP concentration constant, resulted in a corresponding increase in the rate of heteroaggregation, which occurred through the bridging of HemNPs by CNT strands. At the optimal CNT/HemNP mass concentration ratio (CNT/HemNP ratio) of 0.0316, the heteroaggregation rate reached 3.3 times of the HemNP homoaggregation rate in the diffusion-limited regime. Increasing the CNT/HemNP ratio above the optimal value, however, led to a dramatic decrease in the growth rate of heteroaggregates, likely through a blocking mechanism. In the presence of humic acid, the trends in the variation of the heteroaggregation rate with CNT/HemNP ratio were similar to that in the absence of humic acid. However, as the humic acid concentration was increased, the maximum aggregate growth rate decreased due to the lessening in the available surface of the HemNPs that CNTs can attach to through favorable electrostatic interaction.

Interaction of Multiwalled Carbon Nanotubes with Supported Lipid Bilayers and Vesicles as Model Biological Membranes

The influence of solution chemistry on the kinetics and reversibility of the deposition of multiwalled carbon nanotubes (MWNTs) on model biological membranes was investigated using a quartz crystal microbalance with dissipation monitoring (QCM-D). Supported lipid bilayers (SLBs) comprised of zwitterionic 1,2-dioleoyl-sn-glyero-3-phosphocholine (DOPC), as well as DOPC vesicles, were used as model cell membranes. Under neutral pH conditions, the deposition kinetics of MWNTs on SLBs increased with increasing electrolyte (NaCl and CaCl2) concentrations. In the presence of NaCl, favorable deposition was not achieved even at a concentration of 1 M, which is attributed to the presence of strong repulsive hydration forces due to the highly hydrophilic headgroups of SLBs. Conversely, favorable deposition was observed at CaCl2 concentrations above 0.5 mM when the charge of SLBs was reversed from negative to positive through the binding of Ca(2+) cations to the exposed phosphate headgroups. Favorable nanotube deposition was also observed at pH 2, at which the DOPC SLBs exhibited positive surface charge, since the isoelectric point of DOPC is ca. 4. When MWNTs on SLBs were rinsed with low ionic strength solutions at pH 7.3, only ca. 20% of deposited nanotubes were released, indicating that nanotube deposition was mostly irreversible. The deposition of MWNTs on DOPC vesicles under favorable deposition conditions did not result in any detectable leakage of solution from the vesicles, indicating that MWNTs did not severely disrupt the DOPC bilayers upon attachment.

Influence of Solution Chemistry on the Release of Multiwalled Carbon Nanotubes from Silica Surfaces

The release of multiwalled carbon nanotubes (MWNTs) that were deposited on silica surfaces was investigated using a quartz crystal microbalance with dissipation monitoring (QCM-D). MWNTs were deposited on silica surfaces at elevated NaCl and CaCl2 concentrations before being rinsed with eluents of different solution chemistries to induce their remobilization. Energetically speaking, the MWNTs were released from the primary energy minimum when the background NaCl or CaCl2 concentrations were decreased at pH 7.1. The increase in electrostatic repulsion between MWNTs and silica likely caused a reduction in the energy barrier, which enabled the release of MWNTs. The degree of release increased in a stepwise fashion when the nanotubes were sequentially exposed to eluents of decreasing electrolyte concentrations, possibly due to the heterogeneity in nanotube surface charge densities. The degree of release via a successive reduction in NaCl concentration was lower at pH 4.0 than at 7.1 due to MWNTs and silica surfaces exhibiting a less negative surface charge at pH 4.0. Most of the deposited MWNTs were released when the pH was decreased from 7.1 to 4.0 at 1.5 mM CaCl2. This was attributed to the elimination of calcium bridging between the carboxyl groups on MWNTs and silanol groups on silica surfaces.

Adsorption kinetics and reversibility of linear plasmid DNA on silica surfaces: influence of alkaline earth and transition metal ions.

A quartz crystal microbalance with dissipation monitoring is used to study the adsorption of linear plasmid DNA on silica surfaces and silica surfaces coated with poly-L-lysine (PLL) in solutions containing either alkaline earth (calcium and magnesium) or transition (cobalt, copper, and zinc) metals. Our results show that electrostatic attraction alone does not fully explain the significantly higher adsorption rate of DNA on the positively charged PLL layer in Cu(2+) solution compared to solutions containing Ca(2+), Mg(2+), Co(2+), or Zn(2+). Diffusion coefficients measured by dynamic light scattering reveal that the compactness of plasmid DNA molecules is greater in solutions containing Cu(2+) compared to that of DNA in other divalent electrolyte solutions. When the adsorption rate of plasmid DNA on silica is normalized to the corresponding adsorption rate on PLL-coated surfaces at the same solution condition, the attachment (adsorption) efficiencies are about 0.01 for Ca(2+) or Mg(2), but close to unity for Co(2+), Cu(2+), or Zn(2+). Results from viscoelastic modeling of adsorbed DNA layers suggest that the DNA layer formed in Cu(2+) solutions is thicker and more viscous compared to that formed in Co(2+) solutions. This study demonstrates that plasmid DNA has a strong affinity to Cu(2+), which results in a more compact conformation of DNA molecules compared to the case with the other divalent cations investigated.

Release kinetics of multiwalled carbon nanotubes deposited on silica surfaces: quartz crystal microbalance with dissipation (QCM-D) measurements and modeling.

Understanding the kinetics of the release of carbon nanotubes (CNTs) from naturally occurring surfaces is crucial for the prediction of the environmental fate and transport of CNTs. In this study, the release kinetics of multiwalled CNTs (MWNTs) from silica surfaces was investigated using a quartz crystal microbalance with dissipation monitoring (QCM-D). MWNTs were first deposited on silica surfaces under favorable deposition conditions (1.50 mM CaCl2 and pH 7.1) and the deposited MWNTs were then rinsed at different electrolyte solutions to induce the release of MWNTs from the primary energy minimum. The kinetics of MWNT release was shown to be first order with respect to the deposited MWNTs when complete release took place. A model that accounts for the releasable and unreleasable components of MWNTs was used to fit the experimental data in order to derive the release rate coefficients. When the CaCl2 concentration in the eluent was decreased, a larger fraction of deposited MWNTs was released and the release rate coefficient of the releasable MWNTs also increased. The rise in the surface charges of both MWNTs and silica surfaces with the drop in CaCl2 concentration likely resulted in the decrease in the height of the energy barrier, thus facilitating the release of the nanotubes. Moreover, when the initial surface concentrations of deposited MWNTs were over 1000 ng/cm(2), the release rate coefficient was lower than expected. The reduced release kinetics was likely due to the formation of large surface-bound MWNT clusters which had considerably lower diffusion coefficients than dispersed MWNTs or MWNT aggregates.

Aggregation and interactions of chemical mechanical planarization nanoparticles with model biological membranes: role of phosphate adsorption

In the semiconductor industry, chemical mechanical planarization (CMP) slurries are used in large quantities for the planarization of wafers and the release of CMP nanoparticles (NPs) into the natural environment may pose a threat to human health. In this study, the aggregation behavior of four model CMP NPs, namely, colloidal SiO2, fumed SiO2, CeO2, and Al2O3 NPs, was investigated through dynamic light scattering in the presence and absence of phosphate at pH 7.4. The colloidal and fumed SiO2 NPs were observed to have remarkable stability under neutral pH conditions both in the presence and absence of phosphate. Phosphate adsorption enhanced the negative surface charge of CeO2 NPs and reversed the charge of Al2O3 NPs, resulting in an increase in the stability of both NPs. In order to evaluate the propensity for the CMP NPs to attach to and disrupt cell membranes, the interactions of these NPs with supported lipid bilayers (SLBs) and lipid vesicles composed of zwitterionic 1,2-dioleoyl-sn-glycero-3-phosphocholine (DOPC) were examined using a quartz crystal microbalance. The attachment efficiencies of both SiO2 NPs on SLBs increased to 1 when the NaCl concentration was raised to 100 mM in the presence of phosphate. In contrast, favorable attachment of CeO2 and Al2O3 NPs to SLBs was not achieved in the presence of phosphate even at elevated NaCl concentrations, likely due to the enhancement of nanoparticle surface charge resulting from phosphate adsorption. When the supported vesicles were exposed to the SiO2 NPs, no disruption of vesicles was detected despite favorable conditions for nanoparticle–membrane association.