Kalle Ilves

Steady-State Analysis of Interaction Between Harmonic Components of Arm and Line Quantities of Modular Multilevel Converters

The fundamental frequency component in the arm currents of a modular multilevel converter is a necessity for the operation of the converter, as is the connection and bypassing of the submodules. Inevitably, this will cause alternating components in the capacitor voltages. This paper investigates how the arm currents and capacitor voltages interact when the submodules are connected and bypassed in a sinusoidal manner. Equations that describe the circulating current that is caused by the variations in the total inserted voltage are derived. Resonant frequencies are identified and the resonant behaviour is verified by experimental results. It is also found that the effective values of the arm resistance and submodule capacitances can be extracted from the measurements by least square fitting of the analytical expressions to the measured values. Finally, the analytical expression for the arm currents is verified by experimental results.

Open-Loop Control of Modular Multilevel Converters Using Estimation of Stored Energy

The internal control of a modular multilevel converter aims to equalize and stabilize the submodule capacitor voltages independent of the loading conditions. It has been shown that a submodule selection mechanism, included in the modulator, can provide voltage sharing inside the converter arm. Several procedures for controlling the total stored energy in each converter arm exist. A new approach is described in this paper. It is based on estimation of the stored energy in the arms by combining the converter electromotive force reference, the measured alternating output current, and the known direct voltage. No feedback controllers are used. Experimental verification on a three-phase 10 kVA prototype is presented along with the description of the new procedure.

A New Modulation Method for the Modular Multilevel Converter Allowing Fundamental Switching Frequency

This paper presents a new modulation method for the modular multilevel converter. The proposed method is based on a fixed pulse pattern where harmonic elimination methods can be applied. In the proposed modulation method, the pulse pattern is chosen in such a way that the stored energy in each submodule remains stable. It is shown that this can be done at the fundamental switching frequency without measuring the capacitor voltages or using any other form of feedback control. Such a modulation scheme has not been presented before. The theoretical results are verified by both simulations and experimental results. The simulation results show successful operation at the fundamental switching frequency with a larger number of submodules. When a smaller number of submodules are used, harmonic elimination methods may be applied. This is verified experimentally on a converter with eight submodules per phase leg. The experimental results verify that stable operation can be maintained at the fundamental switching frequency while successfully eliminating the fifth harmonic in the ac-side voltage.

On Energy Storage Requirements in Modular Multilevel Converters

The modular multilevel converter is a promising topology for high-voltage and high-power applications. By using submodules equipped with dc-capacitors excellent output voltage waveforms can be obtained at low switching frequencies. The rated energy storage of the submodule capacitors is a driving factor of the size, cost, and weight of the submodules. Although the modular multilevel converter has been thoroughly investigated in the literature, a more detailed analysis of the energy-storage requirements will provide an important contribution for dimensioning and analysis of modular multilevel converters. Such an analysis is presented in this paper. The analysis relates the power transfer capability to the stored energy in the converter and the findings are validated by both simulations and experimental results. The required size of the submodule capacitors in a 4.5 MW grid-connected converter is first calculated and the calculated operating range is then compared with simulation results. The experimental results show that if the average capacitor voltage is allowed to increase 10% above the nominal value an energy storage to power transfer ratio of 21 J/kW can be achieved. It is concluded that the presented theory can relate the power transfer capability to the energy storage in the converter and is thus a valuable tool in the design and analysis of modular multilevel converters.

Evaluation of control and modulation methods for modular multilevel converters

The modular multilevel converter is a promising converter technology for various high-voltage high-power applications. Despite the apparent simplicity of the circuit, the inherent dynamics of the converter and the balancing of the sub-module capacitor voltages impose high requirements on the control system, which can be implemented in quite different ways. To illustrate this, and to provide a guidance for future research on the subject, this paper presents an evaluation of four different control and modulation methods. The investigation is based on experiments on a down-scaled 10 kVA converter having 10 submodules per phase leg. The main items to be investigated are dynamics within the sub-modules, arm voltages and circulating currents. It is found that the suggested open-loop control method provides the fastest arm-voltage response and that the balancing approach based on a sorting algorithm is substantially faster and less complicated to implement than the method using a dedicated voltage controller for each sub-module.

Modular Multilevel Converter AC Motor Drives With Constant Torque From Zero to Nominal Speed

Modular multilevel converters are shown to have a great potential in the area of medium-voltage drives. Low-distortion output quantities combined with low average switching frequencies for the semiconductor devices create an ideal combination for very high-efficiency drives. However, the large number of devices and capacitors that have to conduct the fundamental-frequency current require more complex converter control techniques than its two-level counterpart. Special care needs to be taken for starting and operation at low speeds, where the low-frequency current may cause significant unbalance between the submodule capacitor voltages and disturb the output waveforms. In this paper, principles for converter operation with high torque in the whole speed range are investigated. Experimental results from a down-scaled 12-kVA prototype converter running a loaded motor at various speeds between standstill and the rated speed are also provided.

Inner control of Modular Multilevel Converters - An approach using open-loop estimation of stored energy

The inner control of a Modular Multilevel Converter (M2C) must be designed so that the submodule capacitor voltages are equalized and stable independent of the loading conditions. It has been shown that a submodule selection mechanism, included in the modulator, can provide voltage sharing inside the converter arm. Several procedures for controlling the total stored energy in each converter arm exist. A new approach is described in this paper. It is based on estimation of the arm energy from measured ac output current and dc voltage. No feedback controllers are used. Experimental verification on a 3-phase 10 kVA prototype is presented along with the description of the new procedure.

On interaction between internal converter dynamics and current control of high-performance high-power AC motor drives with modular multilevel converters

The modular multilevel converter (M2C) is a promising converter technology for various high-voltage high-power applications. The reason to this is that low-distortion output quantities can be achieved with low average switching frequencies per switch and without output filters. With the M2C the output voltage has such a low harmonic content that high-power motors can be operated without any derating. However, the apparent large number of devices, requires more complex converter control techniques than a two-level counterpart. Even though there have been several ways suggested to control the converter itself, it is still a challenge to investigate the interaction of these controllers with an external motor current controller. It is shown in the paper that the anticipated interaction will not result in any problems neither for the converter nor for the motor control itself.

Analysis and Operation of Modular Multilevel Converters With Phase-Shifted Carrier PWM

Many publications have been presented on the modulation and control of the modular multilevel converter, some of which are based on phase-shifted carrier modulation. This paper presents an analysis ...

Global Asymptotic Stability of Modular Multilevel Converters

Modular multilevel converters require that the controller is designed so that the submodule capacitor voltages are equalized and stable, independent of the loading conditions. Assuming that the individual capacitor-voltage sharing is managed effectively, an open-loop strategy has been designed to ensure that the total amount of energy stored inside the converter always will be controlled. This strategy, using the steady-state solutions of the dynamic equations for controlling the total stored energy in each converter arm, has proven to be effective. The intention of this paper is to explain in a rigorous way the mechanism behind the suggested strategy and to prove that, when this open-loop strategy is used, the system becomes globally asymptotically stable. Experimental verification on a three-phase 10-kVA prototype is presented.