Kamellia Dalaei

Effect of interpass temperature on residual stresses in multipass welds produced using low transformation temperature filler alloy

Abstract Weld filler alloys that exploit transformation plasticity through low austenite to martensite transformation temperatures offer an effective method of reducing residual stresses in strong steel welds. However, in multipass welds, the heat input from later weld passes may be insufficient to retransform prior welding passes, leading to the accumulation of thermally induced strains and elevated residual stresses. In this work, the residual stress distributions produced around arc welds fabricated with a martensitic weld filler alloy that transforms at a low temperature have been studied as a function of the number of passes deposited and the interpass temperature. It is found that when the interpass temperature is above the transformation temperature of the weld metal, the entire multipass weld transforms as a single entity, thus permitting the optimum exploitation of the transformation plasticity. In contrast, the deposition of new metal with a relatively low interpass temperature leads to increased residual stresses in the underlying layers, reducing or eliminating the beneficial stress states previously created.

Effects of dilution and baseplate strength on stress distributions in multipass welds deposited using low transformation temperature filler alloys

Abstract Transformation plasticity can be utilised to control residual stresses in steel welds. This requires special filler alloys that transform at a sufficiently low temperature to compensate for accumulated thermal contraction strains. However, the welding parameters needed to optimise the effect in multipass joints have yet to be established. This topic has been investigated by characterising the residual stress distribution in multipass welds fabricated with different welding alloys and baseplates using neutron diffraction to assess the effects of dilution and baseplate strength. While the use of richly alloyed weld metal does enhance fatigue performance in single pass joints, the extent of stress relief that can be derived from transformation plasticity is reduced due to incomplete martensitic transformation when further layers are deposited. For all cases studied, compressive stresses were measured in the weld metal with balancing tensile stress in the heat affected zone of the plate. The magnitude of the tension was observed to be a function of the strength of the baseplate. Recommendations are also presented for the combination of welding and material parameters that lead to the optimum exploitation of transformation plasticity as a method for boosting the fatigue performance of multipass welded joints.

Surface residual stresses in multipass welds produced using low transformation temperature filler alloys

Abstract Tensile residual stresses at the surface of welded components are known to compromise fatigue resistance through the accelerated initiation of microcracks, especially at the weld toe. Inducement of compression in these regions is a common technique employed to enhance fatigue performance. Transformation plasticity has been established as a viable method to generate such compressive residual stresses in steel welds and exploits the phase transformation in welding filler alloys that transform at low temperature to compensate for accumulated thermal contraction strains. Neutron and X-ray diffraction have been used to determine the stress profiles that exist across the surface of plates welded with low transformation temperature welding alloys, with a particular focus on the stress at the weld toe. For the first time, near surface neutron diffraction data have shown the extent of local stress variation at the critical, fusion boundary location. Compression was evident for the three measurement orientations at the fusion boundaries. Compressive longitudinal residual stresses and tensile transverse stresses were measured in the weld metal.

Neutron Diffraction Evaluation of Near Surface Residual Stresses at Welds in 1300 MPa Yield Strength Steel

Evaluation of residual stress in the weld toe region is of critical importance. In this paper, the residual stress distribution both near the surface and in depth around the weld toe was investigated using neutron diffraction, complemented with X-ray diffraction. Measurements were done on a 1300 MPa yield strength steel welded using a Low Transformation Temperature (LTT) consumable. Near surface residual stresses, as close as 39 µm below the surface, were measured using neutron diffraction and evaluated by applying a near surface data correction technique. Very steep surface stress gradients within 0.5 mm of the surface were found both at the weld toe and 2 mm into the heat affected zone (HAZ). Neutron results showed that the LTT consumable was capable of inducing near surface compressive residual stresses in all directions at the weld toe. It is concluded that there are very steep stress gradients both transverse to the weld toe line and in the depth direction, at the weld toe in LTT welds. Residual stress in the base material a few millimeters from the weld toe can be very different from the stress at the weld toe. Care must, therefore, be exercised when relating the residual stress to fatigue strength in LTT welds.

Stability of Residual Stresses Created by Shot Peening in Monotonic Loading and at the Presence of Load Reversals - Experiments and Modeling

As a method for mechanical surface treatment, shot peening has been widely used to improve the fatigue strength of materials. However, the influence of residual stresses introduced by shot peening depends on their stability. The stability of residual stresses during fatigue may be studied in two stages: the first cycle and successive cyclic loading. In this study the stability and development of the residual stresses during the first cycle of strain controlled fatigue of normalized steel was investigated. The influence of total strain amplitude and the loading direction was studied. The residual stresses were obtained using the x-ray diffraction technique. It was shown that the stability and relaxation of the residual stresses depend both on the amount and the direction of the loading stresses. Finite element modeling (FEM) was used to rationalize the experimental data. Very good agreement between the experimental and FEM results were observed