Network


Latest external collaboration on country level. Dive into details by clicking on the dots.

Hotspot


Dive into the research topics where Karolina Milenko is active.

Publication


Featured researches published by Karolina Milenko.


Optics Letters | 2012

Photonic crystal fiber tip interferometer for refractive index sensing

Karolina Milenko; Dora Juan Juan Hu; Perry Ping Shum; Taishi Zhang; Jun Long Lim; Yixin Wang; Tomasz R. Wolinski; Huifeng Wei; Weijun Tong

In this paper we present an interferometer based on photonic crystal fiber (PCF) tip ended with a solid silica-sphere for refractive index sensing. The sensor is fabricated by splicing one end of the holey PCF to a single mode fiber (SMF) and applying arc at the other end to form a solid sphere. The sensor has been experimentally tested for refractive index and temperature sensing by monitoring its wavelength shift. Measurement results show that the sensor has the resolution of the order of 8.7×10(-4) over the refractive index range of 1.33-1.40, and temperature sensitivity of the order of 10 pm/°C in the range of 20-100 °C.


IEEE Photonics Journal | 2012

A Compact and Temperature-Sensitive Directional Coupler Based on Photonic Crystal Fiber Filled With Liquid Crystal 6CHBT

Dora Juan Juan Hu; Perry Ping Shum; Jun Long Lim; Ying Cui; Karolina Milenko; Yixin Wang; Tomasz R. Wolinski

A directional coupler structure formed by a nematic liquid crystal (NLC)-filled photonic crystal fiber (PCF) represents a promising configuration in sensing applications. Because of large refractive index difference between the NLC and silica material, the mode coupling between the NLC waveguide and the silica core is more complicated than the situation of coupling between two fundamental modes of the waveguides. Therefore, it is necessary to perform a theoretical investigation of the mode properties associated with the experimental studies of the coupling characteristics. In this paper, we present a thorough analysis, both theoretically and experimentally, of the directional coupler structure, including the mode properties, coupling characteristics, and thermal sensing properties. The temperature response of the device is experimentally measured, showing a polynomial curve in nematic phase and a linear curve in isotropic phase. The nonlinearity of the temperature response of the device in nematic phase and the linearity in isotropic phase are attributed to the temperature dependence of the refractive index of the NLC. Specifically, the sensitivity is -3.86 nm/°C in isotropic phase of the 6CHBT with good linearity and shows good agreement with simulation results.


IEEE Sensors Journal | 2012

A Photonic Crystal Fiber and Fiber Bragg Grating-Based Hybrid Fiber-Optic Sensor System

Ginu Rajan; Manjusha Ramakrishnan; Yuliya Semenova; Karolina Milenko; Piotr Lesiak; Andrzej W. Domanski; Tomasz R. Wolinski; Gerald Farrell

A hybrid sensor that operates in the intensity domain by converting the polarization and wavelength information from the photonic crystal fiber sensor and fiber Bragg grating (FBG) sensor, respectively, into intensity variation is presented in this paper. The hybrid fiber-optic sensor system involves a combination of a polarimetric sensor based on a photonic crystal fiber and a FBG sensor and is used for simultaneous strain and temperature measurement. The strain sensitivity of the polarization maintaining photonic crystal fiber at different lengths and the corresponding slope required for the edge filter which converts the FBG wavelength information into intensity are studied and presented in this paper. The proposed sensor configuration has a wide range of applications in smart fiber-optic sensing.


Molecular Crystals and Liquid Crystals | 2014

Liquid Crystals and Polymer-Based Photonic Crystal Fibers

Tomasz R. Wolinski; Karolina Milenko; Marzena M. Tefelska; Katarzyna A. Rutkowska; Andrzej W. Domanski; Slawomir Ertman; K. Orzechowski; Marek Wojciech Sierakowski; O. Chojnowska; Roman Dąbrowski

Experimental results of polymer photonic liquid crystal fibers based on commercially available (Kiriama) PMMA and cyclo-olefin polymer (Zeonex 480R) microstructured polymer fibers infiltrated with nematic liquid crystals (2CHBT/8CHBT and PCB) are presented and thermally-tuned photonic band-gap propagation mechanism is observed. These preliminary results suggest, that polymers binding to liquid crystals much easier than silica, can offer new opportunities while using polymer-based photonic crystal fibers.


IEEE Photonics Journal | 2012

Temperature-Sensitive Photonic Liquid Crystal Fiber Modal Interferometer

Karolina Milenko; Tomasz R. Wolinski; Perry Ping Shum; Dora Juan Juan Hu

In this paper, we present an experimental investigation of the photonic crystal fiber (PCF) and photonic liquid crystal fiber (PLCF) modal interferometers. The PLCF interferometer is fabricated by infiltrating a liquid crystal (LC) into the PCF and then splicing the effective PLCF between two single-mode fibers (SMF). By heating the PLCF interferometer, we present a possibility to tune optical properties of the propagating light. We also compare PCF- and PLCF-interferometer responses in the presence of changing external temperature conditions.


Photonics Letters of Poland | 2009

Temperature-insensitive fiber optic deformation sensor embedded in composite material

Andrzej W. Domanski; Piotr Lesiak; Karolina Milenko; Anna Boczkowska; Daniel Budaszewski; Slawomir Ertman; Tomasz R. Wolinski

The paper presents the way that colour can serve solving the problem of calibration points indexing in a camera geometrical calibration process. We propose a technique in which indexes of calibration points in a black-and-white chessboard are represented as sets of colour regions in the neighbourhood of calibration points. We provide some general rules for designing a colour calibration chessboard and provide a method of calibration image analysis. We show that this approach leads to obtaining better results than in the case of widely used methods employing information about already indexed points to compute indexes. We also report constraints concerning the technique. Nowadays we are witnessing an increasing need for camera geometrical calibration systems. They are vital for such applications as 3D modelling, 3D reconstruction, assembly control systems, etc. Wherever possible, calibration objects placed in the scene are used in a camera geometrical calibration process. This approach significantly increases accuracy of calibration results and makes the calibration data extraction process easier and universal. There are many geometrical camera calibration techniques for a known calibration scene [1]. A great number of them use as an input calibration points which are localised and indexed in the scene. In this paper we propose the technique of calibration points indexing which uses a colour chessboard. The presented technique was developed by solving problems we encountered during experiments with our earlier methods of camera calibration scene analysis [2]-[3]. In particular, the proposed technique increases the number of indexed points points in case of local lack of calibration points detection. At the beginning of the paper we present a way of designing a chessboard pattern. Then we describe a calibration point indexing method, and finally we show experimental results. A black-and-white chessboard is widely used in order to obtain sub-pixel accuracy of calibration points localisation [1]. Calibration points are defined as corners of chessboard squares. Assuming the availability of rough localisation of these points, the points can be indexed. Noting that differences in distances between neighbouring points in calibration scene images differ slightly, one of the local searching methods can be employed (e.g. [2]). Methods of this type search for a calibration point to be indexed, using a window of a certain size. The position of the window is determined by a vector representing the distance between two previously indexed points in the same row or column. However, experiments show that this approach has its disadvantages, as described below. * E-mail: [email protected] Firstly, there is a danger of omitting some points during indexing in case of local lack of calibration points detection in a neighbourhood (e.g. caused by the presence of non-homogeneous light in the calibration scene). A particularly unfavourable situation is when the local lack of detection effects in the appearance of separated regions of detected calibration points. It is worth saying that such situations are likely to happen for calibration points situated near image borders. Such points are very important for the analysis of optical nonlinearities, and a lack of them can significantly influence the accuracy of distortion modelling. Secondly, such methods may give wrong results in the case of optical distortion with strong nonlinearities when getting information about the neighbouring index is not an easy task. Beside this, the methods are very sensitive to a single false localisation of a calibration point. Such a single false localisation can even result in false indexing of a big set of calibration points. To avoid the above-mentioned problems, we propose using a black-and-white chessboard which contains the coded index of a calibration point in the form of colour squares situated in the nearest neighbourhood of each point. The index of a certain calibration point is determined by colours of four nearest neighbouring squares (Fig.1). An order of squares in such foursome is important. Because the size of a colour square is determined only by the possibility of correct colour detection, the size of a colour square can be smaller than the size of a black or white square. The larger size of a black or white square is determined by the requirements of the exact localisation step which follows the indexing of calibration points [3]. In this step, edge information is extracted from a blackand-white chessboard. This edge information needs larger Artur Nowakowski, Wladyslaw Skarbek Institute of Radioelectronics, Warsaw University of Technology, Nowowiejska 15/19, 00-665 Warszawa, [email protected] Received February 10, 2009; accepted March 27, 2009; published March 31, 2009 http://www.photonics.pl/PLP


Journal of Lightwave Technology | 2016

Intercore Coupling Effects in Multicore Optical Fiber Tapers Using Magnetic Fluid Out-Claddings

Eirini Tagoudi; Karolina Milenko; Stavros Pissadakis

We demonstrate a compact and functional light coupling device based on a multicore optical fiber and a ferrofluidic out-cladding. This magnetic field tuned light coupler was fabricated by tapering down a multicore optical fiber for extending modal profile of the individual cores, while introducing light coupling between them; then, using the ferrofluidic overlayer for affecting the evanescence field of the outer cores through magneto-refractivity. Coupling effects between 2.5 and 4.5 dB were measured between the central core of the multicore fiber and the outer cores, with the application of a magnetic field flux of ~50 G. This intercore coupling photonic device may find application in sensing, communications, imaging, and laser beam delivery.


Journal of Lightwave Technology | 2015

Electric Field Sensing With Photonic Liquid Crystal Fibers Based on Micro-Electrodes Systems

Marzena M. Tefelska; Tomasz R. Wolinski; Slawomir Ertman; Karolina Milenko; R. Laczkowski; Agata Siarkowska; Andrzej W. Domanski

The paper describes four different types of micro-electrodes systems for dynamic electric field sensing with photonic crystal fibers infiltrated with liquid crystals. The shortest switching time ~20 ms was achieved by using a flexible-flat-cable electrode system. A capillary system with four micro-electrodes (τ ~ 36 ms) appeared to be the most convenient to operate with photonic liquid crystal fibers. The capillary system was also theoretically analyzed and presented in this paper.


Photonics Letters of Poland | 2014

Polarization properties of polymer-based photonic crystal fibers

David Poudereux; Karolina Milenko; Artur Dybko; J. M. Otón; Tomasz R. Wolinski

The paper presents the way that colour can serve solving the problem of calibration points indexing in a camera geometrical calibration process. We propose a technique in which indexes of calibration points in a black-and-white chessboard are represented as sets of colour regions in the neighbourhood of calibration points. We provide some general rules for designing a colour calibration chessboard and provide a method of calibration image analysis. We show that this approach leads to obtaining better results than in the case of widely used methods employing information about already indexed points to compute indexes. We also report constraints concerning the technique. Nowadays we are witnessing an increasing need for camera geometrical calibration systems. They are vital for such applications as 3D modelling, 3D reconstruction, assembly control systems, etc. Wherever possible, calibration objects placed in the scene are used in a camera geometrical calibration process. This approach significantly increases accuracy of calibration results and makes the calibration data extraction process easier and universal. There are many geometrical camera calibration techniques for a known calibration scene [1]. A great number of them use as an input calibration points which are localised and indexed in the scene. In this paper we propose the technique of calibration points indexing which uses a colour chessboard. The presented technique was developed by solving problems we encountered during experiments with our earlier methods of camera calibration scene analysis [2]-[3]. In particular, the proposed technique increases the number of indexed points points in case of local lack of calibration points detection. At the beginning of the paper we present a way of designing a chessboard pattern. Then we describe a calibration point indexing method, and finally we show experimental results. A black-and-white chessboard is widely used in order to obtain sub-pixel accuracy of calibration points localisation [1]. Calibration points are defined as corners of chessboard squares. Assuming the availability of rough localisation of these points, the points can be indexed. Noting that differences in distances between neighbouring points in calibration scene images differ slightly, one of the local searching methods can be employed (e.g. [2]). Methods of this type search for a calibration point to be indexed, using a window of a certain size. The position of the window is determined by a vector representing the distance between two previously indexed points in the same row or column. However, experiments show that this approach has its disadvantages, as described below. * E-mail: [email protected] Firstly, there is a danger of omitting some points during indexing in case of local lack of calibration points detection in a neighbourhood (e.g. caused by the presence of non-homogeneous light in the calibration scene). A particularly unfavourable situation is when the local lack of detection effects in the appearance of separated regions of detected calibration points. It is worth saying that such situations are likely to happen for calibration points situated near image borders. Such points are very important for the analysis of optical nonlinearities, and a lack of them can significantly influence the accuracy of distortion modelling. Secondly, such methods may give wrong results in the case of optical distortion with strong nonlinearities when getting information about the neighbouring index is not an easy task. Beside this, the methods are very sensitive to a single false localisation of a calibration point. Such a single false localisation can even result in false indexing of a big set of calibration points. To avoid the above-mentioned problems, we propose using a black-and-white chessboard which contains the coded index of a calibration point in the form of colour squares situated in the nearest neighbourhood of each point. The index of a certain calibration point is determined by colours of four nearest neighbouring squares (Fig.1). An order of squares in such foursome is important. Because the size of a colour square is determined only by the possibility of correct colour detection, the size of a colour square can be smaller than the size of a black or white square. The larger size of a black or white square is determined by the requirements of the exact localisation step which follows the indexing of calibration points [3]. In this step, edge information is extracted from a blackand-white chessboard. This edge information needs larger Artur Nowakowski, Wladyslaw Skarbek Institute of Radioelectronics, Warsaw University of Technology, Nowowiejska 15/19, 00-665 Warszawa, [email protected] Received February 10, 2009; accepted March 27, 2009; published March 31, 2009 http://www.photonics.pl/PLP


Molecular Crystals and Liquid Crystals | 2014

Numerical Analysis of the Phase Birefringence of the Photonic Crystal Fibers Selectively Filled with Liquid Crystal

Karolina Milenko; Slawomir Ertman; Tomasz R. Wolinski

In this work, we present the theoretical investigation of the phase birefringence in a multi-component-glasses photonic crystal fiber, selectively infiltrated with various nematic liquid crystals. We compare the influence of different PCF infiltration patterns on the fiber phase birefringence. The ability to continuously tune birefringence up or down, depending on the direction of LC molecules tilt is also presented.

Collaboration


Dive into the Karolina Milenko's collaboration.

Top Co-Authors

Avatar

Tomasz R. Wolinski

Warsaw University of Technology

View shared research outputs
Top Co-Authors

Avatar

Andrzej W. Domanski

Warsaw University of Technology

View shared research outputs
Top Co-Authors

Avatar

Slawomir Ertman

Warsaw University of Technology

View shared research outputs
Top Co-Authors

Avatar

Marzena M. Tefelska

Warsaw University of Technology

View shared research outputs
Top Co-Authors

Avatar

Katarzyna A. Rutkowska

Warsaw University of Technology

View shared research outputs
Top Co-Authors

Avatar

Piotr Lesiak

Warsaw University of Technology

View shared research outputs
Top Co-Authors

Avatar

Perry Ping Shum

Nanyang Technological University

View shared research outputs
Top Co-Authors

Avatar

Anna Boczkowska

Warsaw University of Technology

View shared research outputs
Top Co-Authors

Avatar

Daniel Budaszewski

Warsaw University of Technology

View shared research outputs
Top Co-Authors

Avatar
Researchain Logo
Decentralizing Knowledge