Katarína Sedlačková

GaAs detectors irradiated by low doses of electrons

Semi-insulating (SI) GaAs detectors were irradiated by 5 MeV electrons up to a dose of 69 kGy, in order to test their radiation hardness. The electric and spectrometric stability of detectors was examined as a function of the absorbed dose. Investigated detectors showed a very good detector radiation resistance within a dose up to 40 kGy followed by deterioration of some spectrometric and electric properties. However, the reverse current and the detector charge collection efficiency showed minimum changes with the overall applied doses. The obtained results will be used as a preliminary study for further radiation-hardness investigations of GaAs detectors against high energy electrons. This will complete our previous studies of GaAs detector radiation hardness against fast neutrons and γ-rays.

MCNPX Monte Carlo simulations of particle transport in SiC semiconductor detectors of fast neutrons

The aim of this paper was to investigate particle transport properties of a fast neutron detector based on silicon carbide. MCNPX (Monte Carlo N-Particle eXtended) code was used in our study because it allows seamless particle transport, thus not only interacting neutrons can be inspected but also secondary particles can be banked for subsequent transport. Modelling of the fast-neutron response of a SiC detector was carried out for fast neutrons produced by 239Pu-Be source with the mean energy of about 4.3 MeV. Using the MCNPX code, the following quantities have been calculated: secondary particle flux densities, reaction rates of elastic/inelastic scattering and other nuclear reactions, distribution of residual ions, deposited energy and energy distribution of pulses. The values of reaction rates calculated for different types of reactions and resulting energy deposition values showed that the incident neutrons transfer part of the carried energy predominantly via elastic scattering on silicon and carbon atoms. Other fast-neutron induced reactions include inelastic scattering and nuclear reactions followed by production of α-particles and protons. Silicon and carbon recoil atoms, α-particles and protons are charged particles which contribute to the detector response. It was demonstrated that although the bare SiC material can register fast neutrons directly, its detection efficiency can be enlarged if it is covered by an appropriate conversion layer. Comparison of the simulation results with experimental data was successfully accomplished.

Semi-insulating GaAs detectors optimized for fast neutron detection

Semi-insulating (SI) GaAs detectors with a HDPE (High Density PolyEthylene) conversion layer were optimized for detection of fast neutrons (from 0.5 MeV to 12 MeV). Based on previous simulations of neutron transport in HDPE and SI GaAs carried out by the Monte Carlo radiation transport computer code MCNPX (Monte Carlo N-Particle eXtended, version 2.5.0) we used a SI GaAs wafer with a larger thickness of 270 μm. The area of a single AuZn Schottky contact was enlarged from 6.25 mm2 to 7.36 mm2. Thanks to the pixel structure of the new metallization the breakdown voltage increased from 60 V to 280 V as deduced from the measured I−V characteristics. Various thicknesses of HDPE layers in the range from 100 μm to 2000 μm were used with SI GaAs detectors for neutron conversion. The measured relative detection efficiency for fast neutrons using SI GaAs detectors with various HDPE thicknesses varied from 0.07 to 0.12% at lower applied voltages, with a maximum for a 500 μm thick conversion layer.

Detection of fast neutrons using detectors based on semi-insulating GaAs

Detectors with AuZn square Schottky contact of the area of 2.5 ? 2.5 mm2 were fabricated. On the back side, the whole area AuGeNi eutectic ohmic contact was evaporated. The thickness of the base material (semi-insulating GaAs) was 220 ?m. The connection of 4 detectors in parallel was tested to get the detection area of 25 mm2. The 239Pu-Be fast neutron source with energies between 0.5 and 12 MeV was used in experimental measurements. We have investigated the optimal thickness of HDPE (high-density polyethylene) conversion layer for fast neutron detection. The spectra of the neutrons were measured by detectors covered by HDPE converter of different thicknesses. The fast neutron detection efficiency proved experimentally was compared with results from simulations performed by MCNPX (Monte Carlo N-Particle eXtended) code.

GaAs detectors irradiated by electrons at different dose rates

The radiation hardness of Semi-Insulating (SI) GaAs detectors against high-energy electrons was investigated. The detectors were irradiated by 5 MeV electrons. The influence of two irradiation parameters, the total absorbed dose (up to 24 kGy) and the applied dose rate (20, 40 and 80 kGy/h), on their spectrometric properties was studied. An 241Am gamma-ray source was used to evaluate the spectrometric properties. The applied dose has negatively affected the detector CCE (Charge Collection Efficiency) and has influenced also the energy resolution. Nevertheless, a global increase of detection efficiency with the dose was observed. Three different dose rates used during irradiation did not affect the CCE, but in the range of doses from 4 to 16 kGy an influence of the applied dose rate upon two other parameters was observed. With higher dose rates, a steeper increase in the detection efficiency and significant worsening of energy resolution were achieved.

Semiconductor detector based on 4H-SiC and analysis of its active region thickness

The 4H polytype silicon carbide is a promising material for radiation-resistant sensors of ionizing particles. The wide band gap of 3.26 eV offers operation at increased temperatures up to several hundred degrees of Celsius. In this work we focused on the analysis of active region thickness of detectors based on 4H-SiC. The detectors investigated are fabricated from a 105 ?m epitaxial layer grown on 350 ?m 4H-SiC substrate. The circular Schottky contacts with diameter of 1.4 mm using an Au/Ni double layer were evaporated onto both sides of the detector material. Three methods for determination of the active thickness were used. The capacitance-voltage measurements allowed us to estimate free carrier concentration profile. The second method was based on detection of ?-particles generated by an 241Am source. Using SRIM calculations and known Bragg curve absorbed energy in detector volume was estimated. The last method consists of measuring detection efficiency of ?-rays at reverse bias voltages up to 500 V.

Detector of fast neutrons based on silicon carbide epitaxial layers

High quality liquid phase epitaxial layer of 4H-SiC with a thickness of 105 μm was used for fabrication of detector with the circular Schottky contact formed by using Au/Ni double layer contact metallization. The detector structure was characterized by current-voltage measurements showing low reverse current density at room temperature. Following the detection of fast neutrons was studied using the 239Pu-Be source with the mean neutron energy of about 4 MeV. Detected spectrum revealed silicon and carbon-recoil ion continuum. The simulation of detection efficiency vs. thickness of the detector active layer shows linear dependence.

Semi-insulating GaAs based detector of fast neutrons produced by D–T nuclear reaction

We have examined semi-insulating (SI) GaAs detectors with high density polyethylene (HDPE) conversion layer by a mono-energetic neutrons with kinetic energy of 16.755 MeV generated by a deuterium—tritium nuclear reaction. First, the influence of HDPE layer thickness on the relative detection efficiency of fast neutrons was studied. The MCNPX (Monte Carlo N-particle eXtended) code has been used to support the analysis of the experiment. The theoretical optimum thickness of the conversion layer was determined to 1.9 mm using the MCNPX code. The HDPE conversion layers of various thicknesses, in the range from 50 μ m to 3200 μ m, were glued on the top Schottky contact of SI GaAs detector in the experiment. The neutron detection efficiency was evaluated from measured spectra and compared to results from simulations. The experimental data showed very good agreement with simulation results. Then the effect of active detector thickness modified by detector reverse bias on neutron detection efficiency was studied. Finally, the effect of the angle of irradiation on neutron detection efficiency was evaluated exhibiting decreasing tendency with increasing deviation from perpendicular direction of impinging neutrons.

Spectrometric properties of semi-insulating GaAs detectors irradiated by 5 MeV electrons at different dose rates

The radiation hardness of Semi-Insulating (SI) GaAs detectors against 5 MeV electrons is investigated in this paper. The influence of two parameters, the accumulative absorbed dose (from 1 to 120 kGy) and the applied dose rate (20, 40 or 80 kGy/h), on detector spectrometric properties was studied. The electron irradiation has negatively affected the detector CCE (Charge Collection Efficiency). Un-irradiated detectors exhibited the CCE of 79% at maximum operating reverse voltage of 300 V and reached the maximum CCE of 51% at 200 V after irradiation by a dose of 120 kGy. Relative energy resolution was also affected by electron irradiation. Its global degradation was observed in the range of doses from 24 up to 120 kGy, where an increase from 19% up to 39% at 200 V reverse voltage was noticed. On the other hand, a global increase of detection efficiency with dose, by about 30% at 120 kGy, was observed with all samples. We did not observe any significant influence of chosen dose rates applied during irradiation on investigated spectrometric properties of detectors.

The influence of high-energy electrons irradiation on the electrical properties of Schottky barrier detectors based on semi-insulating GaAs

In this work we fabricated detectors based on semi-insulating GaAs and studied their electrical properties (current-voltage characteristics, galvanomagnetic measurements) after irradiation with 5 MeV electrons from a linear accelerator up to a dose of 104 kGy. A series of detectors were prepared using Ti/Pt/Au Schottky contact with 1 mm diameter. The thickness of the base material was about 230 μm. A whole area Ni/AuGe/Au ohmic contact was evaporated on the back side. For galvanomagnetic measurements we used three samples from the same wafer. All samples were irradiated by a pulse beam of 5 MeV electrons using the linear accelerator in 11 steps, where the accumulative dose increased from 1 kGy up to 104 kGy. Also different dose rates (20, 40 and 80 kGy/h) were applied to the samples. After each irradiation step we performed electrical measurement of each sample. We analyze the electron Hall mobility, resistivity, electron Hall concentration, breakdown voltage and reverse current of samples before and after irradiation using different dose rates.